101 lines
3.5 KiB
Markdown
101 lines
3.5 KiB
Markdown
|
# SiFive HiFive Unleashed
|
||
|
|
||
|
This page describes how to run coreboot on the [HiFive Unleashed] development
|
||
|
board from [SiFive], the first RISC-V board on the market with enough resources
|
||
|
to run a multiuser operating system.
|
||
|
|
||
|
For general setup instructions, please refer to the [Getting Started Guide].
|
||
|
|
||
|
|
||
|
## TODO
|
||
|
|
||
|
The following things are still missing from this coreboot port:
|
||
|
|
||
|
- Support running romstage from flash (fix stack) to support boot mode 1
|
||
|
- Starting the U54 cores
|
||
|
- FU540 PIN configuration and GPIO access macros
|
||
|
- Provide serial number to payload (e.g. in device tree)
|
||
|
- Implement instruction emulation
|
||
|
- Support for booting Linux on RISC-V
|
||
|
- SMP support in trap handler
|
||
|
|
||
|
## Configuration
|
||
|
|
||
|
Run `make menuconfig` and select _SiFive_/_HiFive Unleashed_ in the _Mainboard_
|
||
|
menu.
|
||
|
|
||
|
|
||
|
### Boot modes
|
||
|
|
||
|
A total of 16 boot modes can be configured using the switches labeled `MSEL0`
|
||
|
through `MSEL3`. The most important ones are as follows:
|
||
|
|
||
|
- **MSEL=1**: Jump directly into the SPI flash, bypassing ROM1
|
||
|
- **MSEL=11**: Load FSBL from SD-card
|
||
|
- **MSEL=15**: Default boot mode; Load FSBL/coreboot from a GPT partition on
|
||
|
SPI flash
|
||
|
|
||
|
|
||
|
## Flashing coreboot
|
||
|
|
||
|
The HiFive Unleashed has an 32 MiB SPI flash (**ISSI IS25WP256D**), that can be
|
||
|
programmed from within Linux running on the board, via USB/JTAG, or directly
|
||
|
with an SPI programmer.
|
||
|
|
||
|
### Internal programming
|
||
|
|
||
|
The SPI flash can be accessed as `/dev/mtd0` from Linux.
|
||
|
|
||
|
### USB/JTAG
|
||
|
|
||
|
To program the flash via USB/JTAG, connect the USB port to a computer. If the
|
||
|
board is powered on, two new serial ports, for example `/dev/ttyUSB0` and
|
||
|
`/dev/ttyUSB1` will appear. The first is JTAG, and the second is connected to
|
||
|
the SoC's UART.
|
||
|
|
||
|
- Download and build the [RISC-V fork of OpenOCD].
|
||
|
- Download the [OpenOCD script] for Freedom Unleashed.
|
||
|
- Start OpenOCD with `openocd -f openocd.cfg`
|
||
|
- Connect to OpenOCD's command interface (via telnet) and enter the line
|
||
|
marked with `> `:
|
||
|
```
|
||
|
> flash write_image erase unlock build/coreboot.rom 0x20000000
|
||
|
auto erase enabled
|
||
|
auto unlock enabled
|
||
|
wrote 33554432 bytes from file build/coreboot.rom in 1524.943848s (21.488 KiB/s)
|
||
|
```
|
||
|
Note that programming the whole flash with OpenOCD isn't fast. In this
|
||
|
example it took just over 25 minutes. This process can be sped up
|
||
|
considerably by building/flashing a smaller image; OpenOCD does not check if
|
||
|
the image and the flash have the same size.
|
||
|
|
||
|
|
||
|
### External programming
|
||
|
|
||
|
External programming with an SPI adapter and [flashrom] may work, but has not
|
||
|
been tested. Please study the [schematics] before going this route.
|
||
|
|
||
|
|
||
|
## Error codes
|
||
|
|
||
|
The zeroth-stage bootloader (ZSBL) in ROM1 can print error codes on the serial
|
||
|
console in certain situations.
|
||
|
|
||
|
```
|
||
|
// Error codes are formatted as follows:
|
||
|
// [63:60] [59:56] [55:0]
|
||
|
// bootstage trap errorcode
|
||
|
// If trap == 1, then errorcode is actually the mcause register with the
|
||
|
// interrupt bit shifted to bit 55.
|
||
|
```
|
||
|
(--- from the [SiFive forum](https://forums.sifive.com/t/loading-fsbl-from-sd/1156/4))
|
||
|
|
||
|
|
||
|
[HiFive Unleashed]: https://www.crowdsupply.com/sifive/hifive-unleashed
|
||
|
[SiFive]: https://www.sifive.com/
|
||
|
[Getting Started Guide]: https://sifive.cdn.prismic.io/sifive%2Ffa3a584a-a02f-4fda-b758-a2def05f49f9_hifive-unleashed-getting-started-guide-v1p1.pdf
|
||
|
[RISC-V fork of OpenOCD]: https://github.com/riscv/riscv-openocd
|
||
|
[OpenOCD script]: https://github.com/sifive/freedom-u-sdk/blob/057a47f657fa33e2c60df7f183884a68e90381cc/bsp/env/freedom-u500-unleashed/openocd.cfg
|
||
|
[flashrom]: https://flashrom.org/Flashrom
|
||
|
[schematics]: https://sifive.cdn.prismic.io/sifive%2Ff7173056-bf37-4407-87cb-d5ab76abf61a_hifive-unleashed-a00-schematics.pdf
|