/* Copyright 2019 The Chromium OS Authors. All rights reserved.
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

/* Intel BASEBOARD-RVP ITE EC specific configuration */

#include "common.h"
#include "it83xx_pd.h"
#include "keyboard_scan.h"
#include "pwm.h"
#include "pwm_chip.h"
#include "timer.h"
#include "usb_pd_tcpm.h"

/* USB-C TPCP Configuration */
const struct tcpc_config_t tcpc_config[CONFIG_USB_PD_PORT_COUNT] = {
	[TYPE_C_PORT_0] = {
		.bus_type = EC_BUS_TYPE_EMBEDDED,
		/* TCPC is embedded within EC so no i2c config needed */
		.drv = &it83xx_tcpm_drv,
#ifdef CONFIG_INTEL_VIRTUAL_MUX
		.usb23 = TYPE_C_PORT_0_USB2_NUM | (TYPE_C_PORT_0_USB3_NUM << 4),
#endif
	},
#ifdef HAS_TASK_PD_C1
	[TYPE_C_PORT_1] = {
		.bus_type = EC_BUS_TYPE_EMBEDDED,
		/* TCPC is embedded within EC so no i2c config needed */
		.drv = &it83xx_tcpm_drv,
#ifdef CONFIG_INTEL_VIRTUAL_MUX
		.usb23 = TYPE_C_PORT_1_USB2_NUM | (TYPE_C_PORT_1_USB3_NUM << 4),
#endif
	},
#endif /* HAS_TASK_PD_C1 */
};
BUILD_ASSERT(ARRAY_SIZE(tcpc_config) == CONFIG_USB_PD_PORT_COUNT);

/* Reset PD MCU */
void board_reset_pd_mcu(void)
{
	/* Not applicable for ITE TCPC */
}

uint16_t tcpc_get_alert_status(void)
{
	/*
	 * Since C0/C1 TCPC are embedded within EC, we don't need the
	 * PDCMD tasks. The (embedded) TCPC status since chip driver
	 * code handles its own interrupts and forward the correct
	 * events to the PD_C0 task. See it83xx/intc.c
	 */

	return 0;
}

/* Keyboard scan setting */
struct keyboard_scan_config keyscan_config = {
	.output_settle_us = 35,
	.debounce_down_us = 5 * MSEC,
	.debounce_up_us = 40 * MSEC,
	.scan_period_us = 3 * MSEC,
	.min_post_scan_delay_us = 1000,
	.poll_timeout_us = 100 * MSEC,
	.actual_key_mask = {
		0x14, 0xff, 0xff, 0xff, 0xff, 0xf5, 0xff,
		0xa4, 0xff, 0xfe, 0x55, 0xfa, 0xca  /* full set */
	},
};

/*
 * PWM HW channelx binding tachometer channelx for fan control.
 * Four tachometer input pins but two tachometer modules only,
 * so always binding [TACH_CH_TACH0A | TACH_CH_TACH0B] and/or
 * [TACH_CH_TACH1A | TACH_CH_TACH1B]
 */
const struct fan_tach_t fan_tach[] = {
	[PWM_HW_CH_DCR0] = {
		.ch_tach = TACH_CH_NULL,
		.fan_p = -1,
		.rpm_re = -1,
		.s_duty = -1,
	},
	[PWM_HW_CH_DCR1] = {
		.ch_tach = TACH_CH_NULL,
		.fan_p = -1,
		.rpm_re = -1,
		.s_duty = -1,
	},
	[PWM_HW_CH_DCR2] = {
		.ch_tach = TACH_CH_TACH1A,
		.fan_p = 2,
		.rpm_re = 1,
		.s_duty = 1,
	},
	[PWM_HW_CH_DCR3] = {
		.ch_tach = TACH_CH_NULL,
		.fan_p = -1,
		.rpm_re = -1,
		.s_duty = -1,
	},
	[PWM_HW_CH_DCR4] = {
		.ch_tach = TACH_CH_NULL,
		.fan_p = -1,
		.rpm_re = -1,
		.s_duty = -1,
	},
	[PWM_HW_CH_DCR5] = {
		.ch_tach = TACH_CH_NULL,
		.fan_p = -1,
		.rpm_re = -1,
		.s_duty = -1,
	},
	[PWM_HW_CH_DCR6] = {
		.ch_tach = TACH_CH_NULL,
		.fan_p = -1,
		.rpm_re = -1,
		.s_duty = -1,
	},
	[PWM_HW_CH_DCR7] = {
		.ch_tach = TACH_CH_NULL,
		.fan_p = -1,
		.rpm_re = -1,
		.s_duty = -1,
	},
};
BUILD_ASSERT(ARRAY_SIZE(fan_tach) == PWM_HW_CH_TOTAL);

/* PWM channels */
const struct pwm_t pwm_channels[] = {
	[PWM_CH_FAN] = {
		.channel = PWM_HW_CH_DCR2,
		.flags = PWM_CONFIG_HAS_RPM_MODE,
		.freq_hz = 30000,
		.pcfsr_sel = PWM_PRESCALER_C7,
	},
};
BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT);

#ifdef CONFIG_USBC_VCONN
void board_pd_vconn_ctrl(int port, enum usbpd_cc_pin cc_pin, int enabled)
{
	/*
	 * Setting VCONN low by disabling the power switch before
	 * enabling the VCONN on respective CC line
	 */
	gpio_set_level(tcpc_gpios[port].vconn.cc1_pin,
			!tcpc_gpios[port].vconn.pin_pol);
	gpio_set_level(tcpc_gpios[port].vconn.cc2_pin,
			!tcpc_gpios[port].vconn.pin_pol);

	if (enabled)
		gpio_set_level((cc_pin != USBPD_CC_PIN_1) ?
				tcpc_gpios[port].vconn.cc2_pin :
				tcpc_gpios[port].vconn.cc1_pin,
				tcpc_gpios[port].vconn.pin_pol);
}
#endif