/* Copyright 2015 The Chromium OS Authors. All rights reserved. * Use of this source code is governed by a BSD-style license that can be * found in the LICENSE file. */ /* oak board configuration */ #ifndef __CROS_EC_BOARD_H #define __CROS_EC_BOARD_H /* board revision */ #include "board_revs.h" #if BOARD_REV >= OAK_REV5 #define CONFIG_ACCELGYRO_BMI160 #define CONFIG_ACCEL_KX022 #define CONFIG_CMD_ACCELS #define CONFIG_CMD_ACCEL_INFO #endif #define CONFIG_ADC #undef CONFIG_ADC_WATCHDOG #if BOARD_REV >= OAK_REV5 /* Add for Ambient Light Sensor */ #define CONFIG_ALS_OPT3001 #define CONFIG_CMD_ALS #endif /* Add for AC adaptor, charger, battery */ #define CONFIG_BATTERY_CUT_OFF #define CONFIG_BATTERY_PRESENT_GPIO GPIO_BAT_PRESENT_L #define CONFIG_BATTERY_REQUESTS_NIL_WHEN_DEAD #define CONFIG_BATTERY_SMART #define CONFIG_CHARGE_MANAGER #define CONFIG_CHARGER #define CONFIG_CHARGER_INPUT_CURRENT 512 #if BOARD_REV == OAK_REV1 #define CONFIG_CHARGER_BQ24773 #define CONFIG_CHARGER_MAX_INPUT_CURRENT 2150 #define CONFIG_CHARGER_SENSE_RESISTOR 10 #define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 #else #define CONFIG_CHARGE_RAMP_HW #define CONFIG_CHARGER_ISL9237 #define CONFIG_CHARGER_MAX_INPUT_CURRENT 2250 #define CONFIG_CHARGER_SENSE_RESISTOR 10 #define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 #endif /* BOARD_REV */ #define CONFIG_CHARGER_DISCHARGE_ON_AC #define CONFIG_CHIPSET_MT817X #define CONFIG_CMD_TYPEC #define CONFIG_EXTPOWER_GPIO #define CONFIG_FORCE_CONSOLE_RESUME #define CONFIG_CMD_CHARGER_ADC_AMON_BMON /* * EC_WAKE: PA0 - WKUP1 * POWER_BUTTON_L: PB5 - WKUP6 */ #define CONFIG_HIBERNATE #if BOARD_REV <= OAK_REV4 #define CONFIG_HIBERNATE_WAKEUP_PINS (STM32_PWR_CSR_EWUP6) #else #define CONFIG_HIBERNATE_WAKEUP_PINS (STM32_PWR_CSR_EWUP1) #define CONFIG_LID_ANGLE #define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL #define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL #define CONFIG_LID_ANGLE_UPDATE #endif /* BOARD_REV */ #define CONFIG_HOST_COMMAND_STATUS #define CONFIG_HOSTCMD_PD #define CONFIG_HOSTCMD_PD_PANIC #define CONFIG_I2C #define CONFIG_I2C_MASTER #define CONFIG_KEYBOARD_COL2_INVERTED #define CONFIG_KEYBOARD_PROTOCOL_MKBP #define CONFIG_LED_COMMON #define CONFIG_LID_SWITCH #define CONFIG_LOW_POWER_IDLE #define CONFIG_MKBP_EVENT #define CONFIG_MKBP_USE_GPIO #define CONFIG_POWER_BUTTON #define CONFIG_POWER_COMMON #define CONFIG_USB_CHARGER #define CONFIG_USBC_SS_MUX #define CONFIG_USBC_SS_MUX_DFP_ONLY #define CONFIG_USBC_VCONN #define CONFIG_USBC_VCONN_SWAP #define CONFIG_USB_POWER_DELIVERY #define CONFIG_USB_PD_ALT_MODE #define CONFIG_USB_PD_ALT_MODE_DFP #define CONFIG_USB_PD_DUAL_ROLE #define CONFIG_USB_PD_LOGGING #define CONFIG_USB_PD_PORT_COUNT 2 #define CONFIG_USB_PD_TCPM_TCPCI #define CONFIG_USB_PD_TRY_SRC #define CONFIG_USB_PD_VBUS_DETECT_TCPC #define CONFIG_SPI #define CONFIG_SPI_MASTER #define CONFIG_STM_HWTIMER32 #define CONFIG_VBOOT_HASH #undef CONFIG_WATCHDOG_HELP #define CONFIG_SWITCH #define CONFIG_BOARD_VERSION_GPIO #undef CONFIG_UART_CONSOLE #define CONFIG_UART_CONSOLE 1 #define CONFIG_TEMP_SENSOR #define CONFIG_TEMP_SENSOR_TMP432 #define CONFIG_DPTF /* UART DMA */ #undef CONFIG_UART_TX_DMA #undef CONFIG_UART_RX_DMA /* * Allow dangerous commands. * TODO: Remove this config before production. */ #define CONFIG_SYSTEM_UNLOCKED /* Optional features */ #define CONFIG_CMD_HOSTCMD /* Drivers */ /* USB Mux */ #define CONFIG_USB_MUX_PI3USB30532 #if BOARD_REV >= OAK_REV5 #define CONFIG_USB_MUX_PS8740 #endif /* BC 1.2 charger */ #define CONFIG_BC12_DETECT_PI3USB9281 #define CONFIG_BC12_DETECT_PI3USB9281_CHIP_COUNT 2 #ifndef __ASSEMBLER__ /* 48 MHz SYSCLK clock frequency */ #define CPU_CLOCK 48000000 /* Keyboard output port list */ #define KB_OUT_PORT_LIST GPIO_A, GPIO_B, GPIO_C, GPIO_D /* 2 I2C master ports, connect to battery, charger, pd and USB switches */ #define I2C_PORT_MASTER 0 #define I2C_PORT_ACCEL 0 #define I2C_PORT_ALS 0 #define I2C_PORT_BATTERY 0 #define I2C_PORT_CHARGER 0 #define I2C_PORT_PERICOM 0 #define I2C_PORT_THERMAL 0 #define I2C_PORT_PD_MCU 1 #define I2C_PORT_USB_MUX 1 #define I2C_PORT_TCPC 1 /* Enable Accel over SPI */ #define CONFIG_SPI_ACCEL_PORT 0 /* First SPI master port (SPI2) */ /* Ambient Light Sensor address */ #define OPT3001_I2C_ADDR_FLAGS OPT3001_I2C_ADDR1_FLAGS /* Timer selection */ #define TIM_CLOCK32 2 #define TIM_WATCHDOG 4 /* Define the host events which are allowed to wakeup AP in S3. */ #define CONFIG_MKBP_HOST_EVENT_WAKEUP_MASK \ (EC_HOST_EVENT_MASK(EC_HOST_EVENT_LID_OPEN) |\ EC_HOST_EVENT_MASK(EC_HOST_EVENT_POWER_BUTTON) |\ EC_HOST_EVENT_MASK(EC_HOST_EVENT_KEY_PRESSED) |\ EC_HOST_EVENT_MASK(EC_HOST_EVENT_KEYBOARD_RECOVERY) |\ EC_HOST_EVENT_MASK(EC_HOST_EVENT_KEYBOARD_FASTBOOT)) #include "gpio_signal.h" enum power_signal { MTK_POWER_GOOD = 0, MTK_SUSPEND_ASSERTED, /* Number of power signals */ POWER_SIGNAL_COUNT }; enum pwm_channel { PWM_CH_POWER_LED = 0, /* Number of PWM channels */ PWM_CH_COUNT }; enum adc_channel { ADC_PSYS = 0, /* PC1: STM32_AIN(2) */ ADC_AMON_BMON, /* PC0: STM32_AIN(10) */ ADC_VBUS, /* PA2: STM32_AIN(11) */ ADC_CH_COUNT }; enum temp_sensor_id { /* TMP432 local and remote sensors */ TEMP_SENSOR_I2C_TMP432_LOCAL, TEMP_SENSOR_I2C_TMP432_REMOTE1, TEMP_SENSOR_I2C_TMP432_REMOTE2, /* Battery temperature sensor */ TEMP_SENSOR_BATTERY, TEMP_SENSOR_COUNT }; enum sensor_id { #ifdef CONFIG_ACCELGYRO_BMI160 BASE_ACCEL, BASE_GYRO, #endif #ifdef CONFIG_ACCEL_KX022 LID_ACCEL, #endif SENSOR_COUNT, }; /* Light sensors */ enum als_id { ALS_OPT3001 = 0, ALS_COUNT }; /* TODO: determine the following board specific type-C power constants */ /* * delay to turn on the power supply max is ~16ms. * delay to turn off the power supply max is about ~180ms. */ #define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ #define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ /* delay to turn on/off vconn */ #define PD_VCONN_SWAP_DELAY 5000 /* us */ /* Define typical operating power and max power */ #define PD_OPERATING_POWER_MW 15000 #define PD_MAX_POWER_MW 60000 #define PD_MAX_CURRENT_MA CONFIG_CHARGER_MAX_INPUT_CURRENT #define PD_MAX_VOLTAGE_MV 20000 /* Reset PD MCU */ void board_reset_pd_mcu(void); /* Set AP reset pin according to parameter */ void board_set_ap_reset(int asserted); /* Control type-C DP route and hotplug detect signal */ void board_typec_dp_on(int port); void board_typec_dp_off(int port, int *dp_flags); void board_typec_dp_set(int port, int level); #endif /* !__ASSEMBLER__ */ #endif /* __CROS_EC_BOARD_H */