/* Copyright 2016 The Chromium OS Authors. All rights reserved. * Use of this source code is governed by a BSD-style license that can be * found in the LICENSE file. */ /* Reef board configuration */ #ifndef __CROS_EC_BOARD_H #define __CROS_EC_BOARD_H /* * By default, enable all console messages excepted HC, ACPI and event: * The sensor stack is generating a lot of activity. */ #define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_LPC))) #undef CONFIG_HOSTCMD_DEBUG_MODE #define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF /* EC console commands */ #define CONFIG_CMD_ACCELS #define CONFIG_CMD_ACCEL_INFO #define CONFIG_CMD_BATT_MFG_ACCESS #define CONFIG_CMD_CHARGER_ADC_AMON_BMON #define CONFIG_CHARGER_SENSE_RESISTOR 10 #define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 #define BD9995X_IOUT_GAIN_SELECT \ BD9995X_CMD_PMON_IOUT_CTRL_SET_IOUT_GAIN_SET_20V #define CONFIG_CHARGER_PSYS_READ #define BD9995X_PSYS_GAIN_SELECT \ BD9995X_CMD_PMON_IOUT_CTRL_SET_PMON_GAIN_SET_02UAW #define CONFIG_CMD_I2C_STRESS_TEST #define CONFIG_CMD_I2C_STRESS_TEST_ACCEL #define CONFIG_CMD_I2C_STRESS_TEST_ALS #define CONFIG_CMD_I2C_STRESS_TEST_BATTERY #define CONFIG_CMD_I2C_STRESS_TEST_CHARGER #define CONFIG_CMD_I2C_STRESS_TEST_TCPC /* Battery */ #define CONFIG_BATTERY_DEVICE_CHEMISTRY "LION" #define CONFIG_BATTERY_CUT_OFF #define CONFIG_BATTERY_PRESENT_CUSTOM #define CONFIG_BATTERY_SMART /* Charger */ #define CONFIG_CHARGE_MANAGER #define CONFIG_CHARGE_RAMP_SW #define CONFIG_CHARGER #define CONFIG_CHARGER_BD9995X #define CONFIG_CHARGER_BD9995X_CHGEN #define CONFIG_CHARGER_DISCHARGE_ON_AC #define CONFIG_CHARGER_INPUT_CURRENT 512 #define CONFIG_CHARGER_LIMIT_POWER_THRESH_BAT_PCT 1 #define CONFIG_CHARGER_LIMIT_POWER_THRESH_CHG_MW 18000 #define CONFIG_CHARGER_MAINTAIN_VBAT #define CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON 1 #define CONFIG_USB_CHARGER #define CONFIG_CHARGER_PROFILE_OVERRIDE #define CONFIG_CHARGER_PROFILE_OVERRIDE_COMMON #undef CONFIG_CHARGER_PROFILE_VOLTAGE_RANGES #define CONFIG_CHARGER_PROFILE_VOLTAGE_RANGES 3 #define CONFIG_CHARGE_MANAGER_EXTERNAL_POWER_LIMIT /* USB-A config */ #define CONFIG_USB_PORT_POWER_SMART #define CONFIG_USB_PORT_POWER_SMART_DEFAULT_MODE USB_CHARGE_MODE_CDP #define CONFIG_USB_PORT_POWER_SMART_SIMPLE #undef CONFIG_USB_PORT_POWER_SMART_PORT_COUNT #define CONFIG_USB_PORT_POWER_SMART_PORT_COUNT 1 #define GPIO_USB1_ILIM_SEL GPIO_USB_A_CHARGE_EN_L #define GPIO_USB_CTL1 GPIO_EN_PP5000 #define CONFIG_TABLET_MODE /* USB PD config */ #define CONFIG_CMD_PD_CONTROL #define CONFIG_USB_PD_ALT_MODE #define CONFIG_USB_PD_ALT_MODE_DFP #define CONFIG_USB_PD_DUAL_ROLE #define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE #define CONFIG_USB_PD_DISCHARGE_TCPC #define CONFIG_USB_PD_LOGGING #define CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT TYPEC_RP_3A0 #define CONFIG_USB_PD_PORT_COUNT 2 #define CONFIG_USB_PD_VBUS_DETECT_CHARGER #define CONFIG_USB_PD_TCPC_LOW_POWER #define CONFIG_USB_PD_TCPM_MUX /* for both PS8751 and ANX3429 */ #define CONFIG_USB_PD_TCPM_ANX3429 #define CONFIG_USB_PD_TCPM_PS8751 #define CONFIG_USB_PD_TCPM_TCPCI #define CONFIG_USB_PD_TRY_SRC #define CONFIG_USB_POWER_DELIVERY #define CONFIG_USB_PD_COMM_LOCKED #define CONFIG_USBC_SS_MUX #define CONFIG_USBC_SS_MUX_DFP_ONLY #define CONFIG_USBC_VCONN #define CONFIG_USBC_VCONN_SWAP /* SoC / PCH */ #define CONFIG_HOSTCMD_LPC #define CONFIG_CHIPSET_APOLLOLAKE #define CONFIG_CHIPSET_RESET_HOOK #define CONFIG_POWER_BUTTON #define CONFIG_POWER_BUTTON_X86 #define CONFIG_POWER_COMMON #define CONFIG_POWER_S0IX #define CONFIG_POWER_TRACK_HOST_SLEEP_STATE /* EC */ #define CONFIG_ADC #define CONFIG_BOARD_VERSION_CUSTOM #define CONFIG_EXTPOWER_GPIO #undef CONFIG_EXTPOWER_DEBOUNCE_MS #define CONFIG_EXTPOWER_DEBOUNCE_MS 1000 #define CONFIG_FPU #define CONFIG_HOSTCMD_FLASH_SPI_INFO #define CONFIG_I2C #define CONFIG_I2C_MASTER #define CONFIG_KEYBOARD_BOARD_CONFIG #define CONFIG_KEYBOARD_PROTOCOL_8042 #define CONFIG_KEYBOARD_COL2_INVERTED #define CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI2 #define CONFIG_LED_COMMON #define CONFIG_LID_SWITCH #define CONFIG_LOW_POWER_IDLE #define CONFIG_LTO #define CONFIG_POWER_SIGNAL_INTERRUPT_STORM_DETECT_THRESHOLD 30 #define CONFIG_PWM #define CONFIG_TEMP_SENSOR #define CONFIG_THERMISTOR_NCP15WB #define CONFIG_STEINHART_HART_3V3_13K7_47K_4050B #define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B #define CONFIG_DPTF #define CONFIG_SCI_GPIO GPIO_PCH_SCI_L #define CONFIG_VOLUME_BUTTONS #define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL #define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL #define CONFIG_VBOOT_HASH #define CONFIG_BACKLIGHT_LID #define CONFIG_WIRELESS #define CONFIG_WIRELESS_SUSPEND EC_WIRELESS_SWITCH_WLAN_POWER #define CONFIG_WLAN_POWER_ACTIVE_LOW #define WIRELESS_GPIO_WLAN_POWER GPIO_WIRELESS_GPIO_WLAN_POWER #define CONFIG_PWR_STATE_DISCHARGE_FULL /* * During shutdown sequence TPS65094x PMIC turns off the sensor rails * asynchronously to the EC. If we access the sensors when the sensor power * rails are off we get I2C errors. To avoid this issue, defer switching * the sensors rate if in S3. By the time deferred function is serviced if * the chipset is in S5 we can back out from switching the sensor rate. * * Time taken by V1P8U rail to go down from S3 is 30ms to 60ms hence defer * the sensor switching after 60ms. */ #undef CONFIG_MOTION_SENSE_SUSPEND_DELAY_US #define CONFIG_MOTION_SENSE_SUSPEND_DELAY_US (MSEC * 60) #define CONFIG_FLASH_SIZE 524288 #define CONFIG_SPI_FLASH_REGS #define CONFIG_SPI_FLASH_W25Q40 /* FIXME: Should be GD25LQ40? */ /* * Enable 1 slot of secure temporary storage to support * suspend/resume with read/write memory training. */ #define CONFIG_VSTORE #define CONFIG_VSTORE_SLOT_COUNT 1 /* Optional feature - used by nuvoton */ #define NPCX_UART_MODULE2 1 /* 0:GPIO10/11 1:GPIO64/65 as UART */ #define NPCX_JTAG_MODULE2 0 /* 0:GPIO21/17/16/20 1:GPIOD5/E2/D4/E5 as JTAG*/ /* FIXME(dhendrix): these pins are just normal GPIOs on Reef. Do we need * to change some other setting to put them in GPIO mode? */ #define NPCX_TACH_SEL2 0 /* 0:GPIO40/73 1:GPIO93/A6 as TACH */ /* I2C ports */ #define I2C_PORT_GYRO NPCX_I2C_PORT1 #define I2C_PORT_LID_ACCEL NPCX_I2C_PORT2 #define I2C_PORT_ALS NPCX_I2C_PORT2 #define I2C_PORT_BARO NPCX_I2C_PORT2 #define I2C_PORT_BATTERY NPCX_I2C_PORT3 #define I2C_PORT_CHARGER NPCX_I2C_PORT3 /* Accelerometer and Gyroscope are the same device. */ #define I2C_PORT_ACCEL I2C_PORT_GYRO /* Sensors */ #define CONFIG_MKBP_EVENT #define CONFIG_MKBP_USE_HOST_EVENT #define CONFIG_ACCELGYRO_BMI160 #define CONFIG_ACCEL_INTERRUPTS #define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) #define CONFIG_MAG_BMI160_BMM150 #define CONFIG_ACCELGYRO_SEC_ADDR_FLAGS BMM150_ADDR0_FLAGS #define CONFIG_MAG_CALIBRATE #define CONFIG_ACCEL_KX022 #define CONFIG_ALS_OPT3001 #define CONFIG_BARO_BMP280 #define CONFIG_LID_ANGLE #define CONFIG_LID_ANGLE_UPDATE #define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL #define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL /* Enable sensor fifo, must also define the _SIZE and _THRES */ #define CONFIG_ACCEL_FIFO /* FIFO size is in power of 2. */ #define CONFIG_ACCEL_FIFO_SIZE 512 /* Depends on how fast the AP boots and typical ODRs */ #define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) #ifndef __ASSEMBLER__ #include "gpio_signal.h" #include "registers.h" /* ADC signal */ enum adc_channel { ADC_TEMP_SENSOR_CHARGER, /* ADC0 */ ADC_TEMP_SENSOR_AMB, /* ADC1 */ ADC_BOARD_ID, /* ADC2 */ ADC_CH_COUNT }; enum pwm_channel { PWM_CH_LED_GREEN = 0, PWM_CH_LED_RED, /* Number of PWM channels */ PWM_CH_COUNT }; enum temp_sensor_id { TEMP_SENSOR_BATTERY = 0, TEMP_SENSOR_AMBIENT, TEMP_SENSOR_CHARGER, TEMP_SENSOR_COUNT }; /* * For backward compatibility, to report ALS via ACPI, * Define the number of ALS sensors: motion_sensor copy the data to the ALS * memmap region. */ #define CONFIG_ALS #define ALS_COUNT 1 /* * Motion sensors: * When reading through IO memory is set up for sensors (LPC is used), * the first 2 entries must be accelerometers, then gyroscope. * For BMI160, accel, gyro and compass sensors must be next to each other. */ enum sensor_id { LID_ACCEL = 0, BASE_ACCEL, BASE_GYRO, BASE_MAG, BASE_BARO, LID_ALS, SENSOR_COUNT, }; enum reef_board_version { BOARD_VERSION_UNKNOWN = -1, BOARD_VERSION_1, BOARD_VERSION_2, BOARD_VERSION_3, BOARD_VERSION_4, BOARD_VERSION_5, BOARD_VERSION_6, BOARD_VERSION_7, BOARD_VERSION_8, BOARD_VERSION_COUNT, }; /* TODO: determine the following board specific type-C power constants */ /* FIXME(dhendrix): verify all of the below PD_* numbers */ /* * delay to turn on the power supply max is ~16ms. * delay to turn off the power supply max is about ~180ms. */ #define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ #define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ /* delay to turn on/off vconn */ #define PD_VCONN_SWAP_DELAY 5000 /* us */ /* Define typical operating power and max power */ #define PD_OPERATING_POWER_MW 15000 #define PD_MAX_POWER_MW 45000 #define PD_MAX_CURRENT_MA 3000 #define PD_MAX_VOLTAGE_MV 20000 /* Reset PD MCU */ void board_reset_pd_mcu(void); int board_get_version(void); void board_set_tcpc_power_mode(int port, int mode); /* Sensors without hardware FIFO are in forced mode */ #define CONFIG_ACCEL_FORCE_MODE_MASK \ (BIT(LID_ACCEL) | BIT(BASE_BARO) | BIT(LID_ALS)) #endif /* !__ASSEMBLER__ */ #endif /* __CROS_EC_BOARD_H */