331 lines
8.8 KiB
C
331 lines
8.8 KiB
C
/* Copyright 2019 The Chromium OS Authors. All rights reserved.
|
|
* Use of this source code is governed by a BSD-style license that can be
|
|
* found in the LICENSE file.
|
|
*/
|
|
|
|
/* Bloog/Blooguard board-specific configuration */
|
|
|
|
#include "adc.h"
|
|
#include "adc_chip.h"
|
|
#include "battery.h"
|
|
#include "button.h"
|
|
#include "charge_manager.h"
|
|
#include "charge_state.h"
|
|
#include "common.h"
|
|
#include "console.h"
|
|
#include "cros_board_info.h"
|
|
#include "driver/accel_kionix.h"
|
|
#include "driver/accelgyro_lsm6dsm.h"
|
|
#include "driver/charger/bd9995x.h"
|
|
#include "driver/ppc/nx20p348x.h"
|
|
#include "driver/tcpm/anx7447.h"
|
|
#include "driver/tcpm/ps8xxx.h"
|
|
#include "driver/tcpm/tcpci.h"
|
|
#include "driver/tcpm/tcpm.h"
|
|
#include "extpower.h"
|
|
#include "gpio.h"
|
|
#include "hooks.h"
|
|
#include "i2c.h"
|
|
#include "keyboard_scan.h"
|
|
#include "lid_switch.h"
|
|
#include "motion_sense.h"
|
|
#include "power.h"
|
|
#include "power_button.h"
|
|
#include "switch.h"
|
|
#include "system.h"
|
|
#include "tablet_mode.h"
|
|
#include "tcpci.h"
|
|
#include "temp_sensor.h"
|
|
#include "thermistor.h"
|
|
#include "usb_mux.h"
|
|
#include "usbc_ppc.h"
|
|
#include "util.h"
|
|
|
|
#define CPRINTSUSB(format, args...) cprints(CC_USBCHARGE, format, ## args)
|
|
#define CPRINTFUSB(format, args...) cprintf(CC_USBCHARGE, format, ## args)
|
|
|
|
#define CPRINTS(format, args...) cprints(CC_SYSTEM, format, ## args)
|
|
|
|
#define USB_PD_PORT_ANX7447 0
|
|
#define USB_PD_PORT_PS8751 1
|
|
|
|
static uint8_t sku_id;
|
|
|
|
static void ppc_interrupt(enum gpio_signal signal)
|
|
{
|
|
switch (signal) {
|
|
case GPIO_USB_PD_C0_INT_ODL:
|
|
nx20p348x_interrupt(0);
|
|
break;
|
|
|
|
case GPIO_USB_PD_C1_INT_ODL:
|
|
nx20p348x_interrupt(1);
|
|
break;
|
|
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
/* Must come after other header files and GPIO interrupts*/
|
|
#include "gpio_list.h"
|
|
|
|
/* ADC channels */
|
|
const struct adc_t adc_channels[] = {
|
|
[ADC_TEMP_SENSOR_AMB] = {
|
|
"TEMP_AMB", NPCX_ADC_CH0, ADC_MAX_VOLT, ADC_READ_MAX+1, 0},
|
|
[ADC_TEMP_SENSOR_CHARGER] = {
|
|
"TEMP_CHARGER", NPCX_ADC_CH1, ADC_MAX_VOLT, ADC_READ_MAX+1, 0},
|
|
/* Vbus C0 sensing (10x voltage divider). PPVAR_USB_C0_VBUS */
|
|
[ADC_VBUS_C0] = {
|
|
"VBUS_C0", NPCX_ADC_CH9, ADC_MAX_VOLT*10, ADC_READ_MAX+1, 0},
|
|
/* Vbus C1 sensing (10x voltage divider). PPVAR_USB_C1_VBUS */
|
|
[ADC_VBUS_C1] = {
|
|
"VBUS_C1", NPCX_ADC_CH4, ADC_MAX_VOLT*10, ADC_READ_MAX+1, 0},
|
|
};
|
|
BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT);
|
|
|
|
const struct temp_sensor_t temp_sensors[] = {
|
|
[TEMP_SENSOR_BATTERY] = {.name = "Battery",
|
|
.type = TEMP_SENSOR_TYPE_BATTERY,
|
|
.read = charge_get_battery_temp,
|
|
.idx = 0,
|
|
.action_delay_sec = 1},
|
|
[TEMP_SENSOR_AMBIENT] = {.name = "Ambient",
|
|
.type = TEMP_SENSOR_TYPE_BOARD,
|
|
.read = get_temp_3v3_51k1_47k_4050b,
|
|
.idx = ADC_TEMP_SENSOR_AMB,
|
|
.action_delay_sec = 5},
|
|
[TEMP_SENSOR_CHARGER] = {.name = "Charger",
|
|
.type = TEMP_SENSOR_TYPE_BOARD,
|
|
.read = get_temp_3v3_13k7_47k_4050b,
|
|
.idx = ADC_TEMP_SENSOR_CHARGER,
|
|
.action_delay_sec = 1},
|
|
};
|
|
BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT);
|
|
|
|
/* Motion sensors */
|
|
/* Mutexes */
|
|
static struct mutex g_lid_mutex;
|
|
static struct mutex g_base_mutex;
|
|
|
|
/* Matrix to rotate accelrator into standard reference frame */
|
|
const mat33_fp_t lid_standrd_ref = {
|
|
{ FLOAT_TO_FP(-1), 0, 0},
|
|
{ 0, FLOAT_TO_FP(1), 0},
|
|
{ 0, 0, FLOAT_TO_FP(-1)}
|
|
};
|
|
|
|
const mat33_fp_t base_standard_ref = {
|
|
{ FLOAT_TO_FP(-1), 0, 0},
|
|
{ 0, FLOAT_TO_FP(-1), 0},
|
|
{ 0, 0, FLOAT_TO_FP(1)}
|
|
};
|
|
|
|
/* sensor private data */
|
|
static struct kionix_accel_data kx022_data;
|
|
static struct lsm6dsm_data lsm6dsm_data;
|
|
|
|
/* Drivers */
|
|
struct motion_sensor_t motion_sensors[] = {
|
|
[LID_ACCEL] = {
|
|
.name = "Lid Accel",
|
|
.active_mask = SENSOR_ACTIVE_S0_S3,
|
|
.chip = MOTIONSENSE_CHIP_KX022,
|
|
.type = MOTIONSENSE_TYPE_ACCEL,
|
|
.location = MOTIONSENSE_LOC_LID,
|
|
.drv = &kionix_accel_drv,
|
|
.mutex = &g_lid_mutex,
|
|
.drv_data = &kx022_data,
|
|
.port = I2C_PORT_SENSOR,
|
|
.i2c_spi_addr_flags = KX022_ADDR1_FLAGS,
|
|
.rot_standard_ref = &lid_standrd_ref,
|
|
.default_range = 2, /* g */
|
|
.config = {
|
|
/* EC use accel for angle detection */
|
|
[SENSOR_CONFIG_EC_S0] = {
|
|
.odr = 10000 | ROUND_UP_FLAG,
|
|
},
|
|
/* Sensor on for lid angle detection */
|
|
[SENSOR_CONFIG_EC_S3] = {
|
|
.odr = 10000 | ROUND_UP_FLAG,
|
|
},
|
|
},
|
|
},
|
|
|
|
[BASE_ACCEL] = {
|
|
.name = "Base Accel",
|
|
.active_mask = SENSOR_ACTIVE_S0_S3,
|
|
.chip = MOTIONSENSE_CHIP_LSM6DSM,
|
|
.type = MOTIONSENSE_TYPE_ACCEL,
|
|
.location = MOTIONSENSE_LOC_BASE,
|
|
.drv = &lsm6dsm_drv,
|
|
.mutex = &g_base_mutex,
|
|
.drv_data = LSM6DSM_ST_DATA(lsm6dsm_data,
|
|
MOTIONSENSE_TYPE_ACCEL),
|
|
.int_signal = GPIO_BASE_SIXAXIS_INT_L,
|
|
.flags = MOTIONSENSE_FLAG_INT_SIGNAL,
|
|
.port = I2C_PORT_SENSOR,
|
|
.i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS,
|
|
.rot_standard_ref = &base_standard_ref,
|
|
.default_range = 2, /* g */
|
|
.min_frequency = LSM6DSM_ODR_MIN_VAL,
|
|
.max_frequency = LSM6DSM_ODR_MAX_VAL,
|
|
.config = {
|
|
/* EC use accel for angle detection */
|
|
[SENSOR_CONFIG_EC_S0] = {
|
|
.odr = 13000 | ROUND_UP_FLAG,
|
|
.ec_rate = 100 * MSEC,
|
|
},
|
|
/* Sensor on for angle detection */
|
|
[SENSOR_CONFIG_EC_S3] = {
|
|
.odr = 10000 | ROUND_UP_FLAG,
|
|
.ec_rate = 100 * MSEC,
|
|
},
|
|
},
|
|
},
|
|
|
|
[BASE_GYRO] = {
|
|
.name = "Base Gyro",
|
|
.active_mask = SENSOR_ACTIVE_S0_S3,
|
|
.chip = MOTIONSENSE_CHIP_LSM6DSM,
|
|
.type = MOTIONSENSE_TYPE_GYRO,
|
|
.location = MOTIONSENSE_LOC_BASE,
|
|
.drv = &lsm6dsm_drv,
|
|
.mutex = &g_base_mutex,
|
|
.drv_data = LSM6DSM_ST_DATA(lsm6dsm_data,
|
|
MOTIONSENSE_TYPE_GYRO),
|
|
.int_signal = GPIO_BASE_SIXAXIS_INT_L,
|
|
.flags = MOTIONSENSE_FLAG_INT_SIGNAL,
|
|
.port = I2C_PORT_SENSOR,
|
|
.i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS,
|
|
.default_range = 1000 | ROUND_UP_FLAG, /* dps */
|
|
.rot_standard_ref = &base_standard_ref,
|
|
.min_frequency = LSM6DSM_ODR_MIN_VAL,
|
|
.max_frequency = LSM6DSM_ODR_MAX_VAL,
|
|
},
|
|
};
|
|
|
|
unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors);
|
|
|
|
/*
|
|
* Returns 1 for boards that are convertible into tablet mode, and zero for
|
|
* clamshells.
|
|
*/
|
|
int board_is_convertible(void)
|
|
{
|
|
/*
|
|
* Bloog: 33, 34, 35, 36
|
|
* Blooguard: 49, 50, 51, 52
|
|
* Unprovisioned: 255
|
|
*/
|
|
return sku_id == 33 || sku_id == 34 || sku_id == 35 || sku_id == 36
|
|
|| sku_id == 49 || sku_id == 50 || sku_id == 51 || sku_id == 52
|
|
|| sku_id == 255;
|
|
}
|
|
|
|
static void board_update_sensor_config_from_sku(void)
|
|
{
|
|
if (board_is_convertible()) {
|
|
motion_sensor_count = ARRAY_SIZE(motion_sensors);
|
|
/* Enable Base Accel interrupt */
|
|
gpio_enable_interrupt(GPIO_BASE_SIXAXIS_INT_L);
|
|
} else {
|
|
motion_sensor_count = 0;
|
|
gmr_tablet_switch_disable();
|
|
/* Base accel is not stuffed, don't allow line to float */
|
|
gpio_set_flags(GPIO_BASE_SIXAXIS_INT_L,
|
|
GPIO_INPUT | GPIO_PULL_DOWN);
|
|
}
|
|
}
|
|
|
|
static void cbi_init(void)
|
|
{
|
|
uint32_t val;
|
|
|
|
if (cbi_get_sku_id(&val) == EC_SUCCESS)
|
|
sku_id = val;
|
|
ccprints("SKU: 0x%04x", sku_id);
|
|
|
|
board_update_sensor_config_from_sku();
|
|
}
|
|
DECLARE_HOOK(HOOK_INIT, cbi_init, HOOK_PRIO_INIT_I2C + 1);
|
|
|
|
void board_hibernate_late(void)
|
|
{
|
|
int i;
|
|
|
|
const uint32_t hibernate_pins[][2] = {
|
|
/* Turn off LEDs before going to hibernate */
|
|
{GPIO_LED_WHITE_C0_L, GPIO_INPUT | GPIO_PULL_UP},
|
|
{GPIO_LED_AMBER_C0_L, GPIO_INPUT | GPIO_PULL_UP},
|
|
{GPIO_LED_WHITE_C1_L, GPIO_INPUT | GPIO_PULL_UP},
|
|
{GPIO_LED_AMBER_C1_L, GPIO_INPUT | GPIO_PULL_UP},
|
|
};
|
|
|
|
for (i = 0; i < ARRAY_SIZE(hibernate_pins); ++i)
|
|
gpio_set_flags(hibernate_pins[i][0], hibernate_pins[i][1]);
|
|
}
|
|
|
|
#ifndef TEST_BUILD
|
|
/* This callback disables keyboard when convertibles are fully open */
|
|
void lid_angle_peripheral_enable(int enable)
|
|
{
|
|
/*
|
|
* If the lid is in tablet position via other sensors,
|
|
* ignore the lid angle, which might be faulty then
|
|
* disable keyboard.
|
|
*/
|
|
if (tablet_get_mode())
|
|
enable = 0;
|
|
|
|
if (board_is_convertible())
|
|
keyboard_scan_enable(enable, KB_SCAN_DISABLE_LID_ANGLE);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_KEYBOARD_FACTORY_TEST
|
|
/*
|
|
* Map keyboard connector pins to EC GPIO pins for factory test.
|
|
* Pins mapped to {-1, -1} are skipped.
|
|
* The connector has 24 pins total, and there is no pin 0.
|
|
*/
|
|
const int keyboard_factory_scan_pins[][2] = {
|
|
{-1, -1}, {0, 5}, {1, 1}, {1, 0}, {0, 6},
|
|
{0, 7}, {1, 4}, {1, 3}, {1, 6}, {1, 7},
|
|
{3, 1}, {2, 0}, {1, 5}, {2, 6}, {2, 7},
|
|
{2, 1}, {2, 4}, {2, 5}, {1, 2}, {2, 3},
|
|
{2, 2}, {3, 0}, {-1, -1}, {-1, -1}, {-1, -1},
|
|
};
|
|
|
|
const int keyboard_factory_scan_pins_used =
|
|
ARRAY_SIZE(keyboard_factory_scan_pins);
|
|
#endif
|
|
|
|
void board_overcurrent_event(int port, int is_overcurrented)
|
|
{
|
|
/* Sanity check the port. */
|
|
if ((port < 0) || (port >= CONFIG_USB_PD_PORT_COUNT))
|
|
return;
|
|
|
|
/* Note that the level is inverted because the pin is active low. */
|
|
gpio_set_level(GPIO_USB_C_OC, !is_overcurrented);
|
|
}
|
|
|
|
uint32_t board_override_feature_flags0(uint32_t flags0)
|
|
{
|
|
/*
|
|
* Remove keyboard backlight feature for devices that don't support it.
|
|
*/
|
|
if (sku_id == 33 || sku_id == 36 || sku_id == 51 ||
|
|
sku_id == 52 || sku_id == 66 || sku_id == 68)
|
|
return (flags0 & ~EC_FEATURE_MASK_0(EC_FEATURE_PWM_KEYB));
|
|
else
|
|
return flags0;
|
|
}
|
|
|
|
uint32_t board_override_feature_flags1(uint32_t flags1)
|
|
{
|
|
return flags1;
|
|
}
|