169 lines
7.8 KiB
C
169 lines
7.8 KiB
C
/* -*- mode:c -*-
|
|
*
|
|
* Copyright 2018 The Chromium OS Authors. All rights reserved.
|
|
* Use of this source code is governed by a BSD-style license that can be
|
|
* found in the LICENSE file.
|
|
*/
|
|
|
|
/* Declare symbolic names for all the GPIOs that we care about.
|
|
* Note: Those with interrupt handlers must be declared first. */
|
|
|
|
/* Wake Source interrupts */
|
|
GPIO_INT(LID_OPEN, PIN(D, 2), GPIO_INT_BOTH |
|
|
GPIO_HIB_WAKE_HIGH, lid_interrupt)
|
|
/*
|
|
* High-to-low transition on POWER_BUTTON_L is treated as a wake event from
|
|
* hibernate. Absence of GPIO_HIB_WAKE_HIGH flag is treated as wake on
|
|
* high-to-low edge.
|
|
*/
|
|
GPIO_INT(POWER_BUTTON_L, PIN(0, 1), GPIO_INT_BOTH, power_button_interrupt) /* MECH_PWR_BTN_ODL */
|
|
GPIO_INT(AC_PRESENT, PIN(0, 0), GPIO_INT_BOTH |
|
|
GPIO_HIB_WAKE_HIGH, extpower_interrupt) /* ACOK_OD */
|
|
|
|
/* USB-C interrupts */
|
|
GPIO_INT(USB_C0_MUX_INT_ODL, PIN(6, 1), GPIO_INT_FALLING, tcpc_alert_event)
|
|
GPIO_INT(USB_C1_MUX_INT_ODL, PIN(F, 5), GPIO_INT_FALLING, tcpc_alert_event)
|
|
GPIO_INT(USB_PD_C0_INT_ODL, PIN(E, 0), GPIO_INT_FALLING, ppc_interrupt)
|
|
GPIO_INT(USB_PD_C1_INT_ODL, PIN(F, 1), GPIO_INT_FALLING, ppc_interrupt)
|
|
|
|
/* Power State interrupts */
|
|
#ifdef CONFIG_POWER_S0IX
|
|
GPIO_INT(PCH_SLP_S0_L, PIN(A, 4), GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S0_L */
|
|
#endif
|
|
GPIO_INT(PCH_SLP_S4_L, PIN(A, 3), GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S4_L */
|
|
GPIO_INT(PCH_SLP_S3_L, PIN(A, 6), GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S3_L */
|
|
GPIO_INT(SUSPWRDNACK, PIN(D, 5), GPIO_INT_BOTH, power_signal_interrupt) /* SUSPWRDNACK */
|
|
GPIO_INT(RSMRST_L_PGOOD, PIN(E, 2), GPIO_INT_BOTH, power_signal_interrupt) /* PMIC_EC_RSMRST_ODL */
|
|
GPIO_INT(ALL_SYS_PGOOD, PIN(F, 4), GPIO_INT_BOTH, power_signal_interrupt) /* PMIC_EC_PWROK_OD */
|
|
|
|
/* Other interrupts */
|
|
GPIO_INT(WP_L, PIN(A, 1), GPIO_INT_BOTH, switch_interrupt) /* EC_WP_ODL */
|
|
|
|
/* Define PCH_SLP_S0_L after all interrupts if CONFIG_POWER_S0IX not defined. */
|
|
#ifndef CONFIG_POWER_S0IX
|
|
GPIO(PCH_SLP_S0_L, PIN(A, 4), GPIO_INPUT) /* SLP_S0_L */
|
|
#endif
|
|
|
|
/*
|
|
* PLT_RST_L isn't used since there is a Virtual Wire on eSPI for it. It is here
|
|
* only for debugging purposes.
|
|
*/
|
|
GPIO(PLT_RST_L, PIN(C, 7), GPIO_INPUT) /* Platform Reset from SoC */
|
|
GPIO(SYS_RESET_L, PIN(3, 4), GPIO_ODR_HIGH) /* SYS_RST_ODL */
|
|
GPIO(PCH_RTCRST, PIN(7, 6), GPIO_OUT_LOW) /* EC_PCH_RTCRST */
|
|
|
|
GPIO(ENTERING_RW, PIN(E, 1), GPIO_OUT_LOW) /* EC_ENTERING_RW */
|
|
GPIO(PCH_WAKE_L, PIN(7, 4), GPIO_ODR_HIGH) /* EC_PCH_WAKE_ODL */
|
|
GPIO(PCH_PWRBTN_L, PIN(C, 1), GPIO_ODR_HIGH) /* EC_PCH_PWR_BTN_ODL */
|
|
|
|
GPIO(EN_PP5000, PIN(7, 3), GPIO_OUT_LOW) /* EN_PP5000_A */
|
|
GPIO(PP5000_PG, PIN(C, 0), GPIO_INPUT) /* PP5000_PG_OD */
|
|
GPIO(EN_PP3300, PIN(D, 4), GPIO_OUT_LOW) /* EN_PP3300_A */
|
|
GPIO(PP3300_PG, PIN(6, 0), GPIO_INPUT) /* PP3300_PG_OD */
|
|
GPIO(PMIC_EN, PIN(7, 2), GPIO_OUT_LOW) /* Enable A Rails via PMIC */
|
|
GPIO(PCH_RSMRST_L, PIN(C, 2), GPIO_OUT_LOW) /* RSMRST# to SOC. All _A rails now up. */
|
|
GPIO(PCH_SYS_PWROK, PIN(B, 7), GPIO_OUT_LOW) /* EC_PCH_PWROK. All S0 rails now up. */
|
|
|
|
/* Peripheral rails */
|
|
GPIO(ENABLE_BACKLIGHT, PIN(D, 3), GPIO_ODR_HIGH |
|
|
GPIO_SEL_1P8V) /* EC_BL_EN_OD */
|
|
GPIO(EN_P3300_TRACKPAD_ODL, PIN(3, 3), GPIO_ODR_HIGH)
|
|
|
|
GPIO(EC_BATT_PRES_L, PIN(E, 5), GPIO_INPUT)
|
|
|
|
/*
|
|
* EC_RST_ODL acts as a wake source from PSL hibernate mode. However, it does
|
|
* not need to be an interrupt for normal EC operations. Thus, configure it as
|
|
* GPIO_INPUT with wake on low-to-high edge using GPIO_HIB_WAKE_HIGH so that PSL
|
|
* common code can configure PSL_IN correctly.
|
|
*
|
|
* Reason for choosing low-to-high edge for waking from hibernate is to avoid
|
|
* the double reset - one because of PSL_IN wake and other because of VCC1_RST
|
|
* being asserted. Also, it should be fine to have the EC in hibernate when H1
|
|
* or servo wants to hold the EC in reset since VCC1 will be down and so entire
|
|
* EC logic (except PSL) as well as AP will be in reset.
|
|
*/
|
|
GPIO(EC_RST_ODL, PIN(0, 2), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH)
|
|
|
|
/*
|
|
* PCH_PROCHOT_ODL is primarily for monitoring the PROCHOT# signal which is
|
|
* normally driven by the PMIC. The EC can also drive this signal in the event
|
|
* that the ambient or charger temperature sensors exceeds their thresholds.
|
|
*/
|
|
GPIO(CPU_PROCHOT, PIN(3, 7), GPIO_INPUT | GPIO_SEL_1P8V) /* PCH_PROCHOT_ODL */
|
|
|
|
/* I2C pins - Alternate function below configures I2C module on these pins */
|
|
GPIO(I2C0_SCL, PIN(B, 5), GPIO_INPUT) /* EC_I2C_BATTERY_3V3_SCL */
|
|
GPIO(I2C0_SDA, PIN(B, 4), GPIO_INPUT) /* EC_I2C_BATTERY_3V3_SDA */
|
|
GPIO(I2C1_SCL, PIN(9, 0), GPIO_INPUT) /* EC_I2C_USB_C0_MUX_SCL */
|
|
GPIO(I2C1_SDA, PIN(8, 7), GPIO_INPUT) /* EC_I2C_USB_C0_MUX_SDA */
|
|
GPIO(I2C2_SCL, PIN(9, 2), GPIO_INPUT) /* EC_I2C_USB_C1_MUX_SCL */
|
|
GPIO(I2C2_SDA, PIN(9, 1), GPIO_INPUT) /* EC_I2C_USB_C1_MUX_SDA */
|
|
GPIO(I2C3_SCL, PIN(D, 1), GPIO_INPUT) /* EC_I2C_EEPROM_SCL */
|
|
GPIO(I2C3_SDA, PIN(D, 0), GPIO_INPUT) /* EC_I2C_EEPROM_SDA */
|
|
GPIO(I2C4_SCL, PIN(F, 3), GPIO_INPUT) /* EC_I2C_CHARGER_3V3_SCL */
|
|
GPIO(I2C4_SDA, PIN(F, 2), GPIO_INPUT) /* EC_I2C_CHARGER_3V3_SDA */
|
|
|
|
/* USB pins */
|
|
GPIO(EN_USB_A0_5V, PIN(6, 7), GPIO_OUT_LOW) /* Enable A0 5V Charging */
|
|
GPIO(EN_USB_A1_5V, PIN(9, 6), GPIO_INPUT | GPIO_PULL_DOWN) /* NC */
|
|
GPIO(USB_A0_CHARGE_EN_L, PIN(A, 2), GPIO_OUT_HIGH) /* Enable A0 1.5A Charging */
|
|
GPIO(USB_A1_CHARGE_EN_L, PIN(A, 0), GPIO_INPUT | GPIO_PULL_DOWN) /* NC */
|
|
|
|
GPIO(USB_C0_PD_RST_ODL, PIN(8, 3), GPIO_ODR_HIGH) /* C0 PD Reset */
|
|
GPIO(USB_C0_BC12_VBUS_ON, PIN(6, 3), GPIO_OUT_LOW) /* C0 BC1.2 Power */
|
|
GPIO(USB_C0_BC12_CHG_DET_L, PIN(9, 5), GPIO_INPUT) /* C0 BC1.2 Detect */
|
|
GPIO(USB_C0_HPD_1V8_ODL, PIN(C, 5), GPIO_INPUT | /* C0 DP Hotplug Detect */
|
|
GPIO_SEL_1P8V)
|
|
GPIO(USB_C1_PD_RST_ODL, PIN(7, 0), GPIO_ODR_HIGH) /* C1 PD Reset */
|
|
GPIO(USB_C1_BC12_VBUS_ON, PIN(B, 1), GPIO_OUT_LOW) /* C1 BC1.2 Power */
|
|
GPIO(USB_C1_BC12_CHG_DET_L, PIN(E, 4), GPIO_INPUT) /* C1 BC1.2 Detect */
|
|
GPIO(USB_C1_HPD_1V8_ODL, PIN(C, 6), GPIO_INPUT | /* C1 DP Hotplug Detect */
|
|
GPIO_SEL_1P8V)
|
|
|
|
/* LED */
|
|
GPIO(BAT_LED_RED_L, PIN(C, 3), GPIO_OUT_HIGH)
|
|
GPIO(BAT_LED_GREEN_L, PIN(C, 4), GPIO_OUT_HIGH)
|
|
GPIO(PWR_LED_BLUE_L, PIN(D, 7), GPIO_OUT_HIGH)
|
|
|
|
/* MKBP event synchronization */
|
|
GPIO(EC_INT_L, PIN(9, 4), GPIO_ODR_HIGH) /* EC_AP_INT_ODL */
|
|
|
|
/* Not implemented in hardware */
|
|
UNIMPLEMENTED(KB_BL_PWR_EN)
|
|
|
|
/* Overcurrent event to host */
|
|
GPIO(USB_C_OC, PIN(3, 6), GPIO_ODR_HIGH | GPIO_SEL_1P8V)
|
|
|
|
/* Strap pins */
|
|
GPIO(GPO66_NC, PIN(6, 6), GPIO_INPUT | GPIO_PULL_UP)
|
|
GPIO(GPOB6_NC, PIN(B, 6), GPIO_INPUT | GPIO_PULL_UP)
|
|
|
|
/* Misc. */
|
|
GPIO(CCD_MODE_ODL, PIN(E, 3), GPIO_INPUT)
|
|
|
|
/* Keyboard pins */
|
|
ALTERNATE(PIN_MASK(3, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_INPUT) /* KSI_00-01 */
|
|
ALTERNATE(PIN_MASK(2, 0xFC), 0, MODULE_KEYBOARD_SCAN, GPIO_INPUT) /* KSI_02-07 */
|
|
ALTERNATE(PIN_MASK(2, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_00-01 */
|
|
ALTERNATE(PIN_MASK(1, 0x7F), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_03-09 */
|
|
ALTERNATE(PIN_MASK(0, 0xF0), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_10-13 */
|
|
ALTERNATE(PIN_MASK(8, 0x04), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_14 */
|
|
GPIO(KBD_KSO2, PIN(1, 7), GPIO_OUT_LOW) /* KSO_02 inverted */
|
|
|
|
/* Alternate functions GPIO definitions */
|
|
/* Cr50 requires no pull-ups on UART pins. */
|
|
ALTERNATE(PIN_MASK(6, 0x30), 0, MODULE_UART, 0) /* UART from EC to Servo */
|
|
ALTERNATE(PIN_MASK(B, 0x30), 0, MODULE_I2C, 0) /* I2C0 */
|
|
ALTERNATE(PIN_MASK(9, 0x07), 0, MODULE_I2C, 0) /* I2C1 SCL / I2C2 */
|
|
ALTERNATE(PIN_MASK(8, 0x80), 0, MODULE_I2C, 0) /* I2C1 SDA */
|
|
ALTERNATE(PIN_MASK(D, 0x03), 0, MODULE_I2C, 0) /* I2C3 */
|
|
ALTERNATE(PIN_MASK(F, 0x0C), 0, MODULE_I2C, 0) /* I2C4 */
|
|
ALTERNATE(PIN_MASK(4, 0x30), 0, MODULE_ADC, 0) /* ADC0-1 */
|
|
|
|
/* Power Switch Logic (PSL) inputs */
|
|
ALTERNATE(PIN_MASK(D, 0x04), 0, MODULE_PMU, 0) /* GPIOD2 = LID_OPEN */
|
|
ALTERNATE(PIN_MASK(0, 0x07), 0, MODULE_PMU, 0) /* GPIO00 = ACOK_OD,
|
|
GPIO01 = MECH_PWR_BTN_ODL
|
|
GPIO02 = EC_RST_ODL */
|