152 lines
4.5 KiB
C
152 lines
4.5 KiB
C
/* Copyright 2016 The Chromium OS Authors. All rights reserved.
|
|
* Use of this source code is governed by a BSD-style license that can be
|
|
* found in the LICENSE file.
|
|
*/
|
|
|
|
/* Servo micro configuration */
|
|
|
|
#ifndef __CROS_EC_BOARD_H
|
|
#define __CROS_EC_BOARD_H
|
|
|
|
/* 48 MHz SYSCLK clock frequency */
|
|
#define CPU_CLOCK 48000000
|
|
|
|
#define CONFIG_BOARD_PRE_INIT
|
|
|
|
/* Enable USART1,3,4 and USB streams */
|
|
#define CONFIG_STREAM_USART
|
|
#define CONFIG_STREAM_USART2
|
|
#define CONFIG_STREAM_USART3
|
|
#define CONFIG_STREAM_USART4
|
|
#define CONFIG_STREAM_USB
|
|
#define CONFIG_CMD_USART_INFO
|
|
|
|
/* The UART console is on USART1 (PA9/PA10) */
|
|
#undef CONFIG_UART_CONSOLE
|
|
#define CONFIG_UART_CONSOLE 1
|
|
#undef CONFIG_UART_TX_DMA
|
|
#undef CONFIG_UART_RX_DMA
|
|
|
|
/* Optional features */
|
|
#define CONFIG_STM_HWTIMER32
|
|
#define CONFIG_HW_CRC
|
|
|
|
/* USB Configuration */
|
|
#define CONFIG_USB
|
|
#define CONFIG_USB_PID 0x501a
|
|
#define CONFIG_USB_CONSOLE
|
|
#define CONFIG_USB_UPDATE
|
|
|
|
#undef CONFIG_USB_MAXPOWER_MA
|
|
#define CONFIG_USB_MAXPOWER_MA 100
|
|
|
|
#define CONFIG_USB_SERIALNO
|
|
#define DEFAULT_SERIALNO "Uninitialized"
|
|
|
|
/* USB interface indexes (use define rather than enum to expand them) */
|
|
#define USB_IFACE_USART4_STREAM 0
|
|
#define USB_IFACE_UPDATE 1
|
|
#define USB_IFACE_SPI 2
|
|
#define USB_IFACE_CONSOLE 3
|
|
#define USB_IFACE_I2C 4
|
|
#define USB_IFACE_USART3_STREAM 5
|
|
#define USB_IFACE_USART2_STREAM 6
|
|
#define USB_IFACE_COUNT 7
|
|
|
|
/* USB endpoint indexes (use define rather than enum to expand them) */
|
|
#define USB_EP_CONTROL 0
|
|
#define USB_EP_USART4_STREAM 1
|
|
#define USB_EP_UPDATE 2
|
|
#define USB_EP_SPI 3
|
|
#define USB_EP_CONSOLE 4
|
|
#define USB_EP_I2C 5
|
|
#define USB_EP_USART3_STREAM 6
|
|
#define USB_EP_USART2_STREAM 7
|
|
#define USB_EP_COUNT 8
|
|
|
|
/* Enable console recasting of GPIO type. */
|
|
#define CONFIG_CMD_GPIO_EXTENDED
|
|
|
|
/* Enable control of SPI over USB */
|
|
#define CONFIG_USB_SPI
|
|
#define CONFIG_SPI_MASTER
|
|
#define CONFIG_SPI_FLASH_PORT 0 /* First SPI master port */
|
|
|
|
/* This is not actually an EC so disable some features. */
|
|
#undef CONFIG_WATCHDOG_HELP
|
|
#undef CONFIG_LID_SWITCH
|
|
|
|
/* Enable control of I2C over USB */
|
|
#define CONFIG_USB_I2C
|
|
#define CONFIG_I2C
|
|
#define CONFIG_I2C_MASTER
|
|
/*
|
|
* iteflash requires 256 byte reads for verifying ITE EC firmware. Without this
|
|
* the limit is CONFIG_I2C_CHIP_MAX_READ_SIZE which is 255 for STM32F0 due to an
|
|
* 8 bit field, per src/platform/ec/include/config.h comment.
|
|
*/
|
|
#define CONFIG_I2C_XFER_LARGE_READ
|
|
#define I2C_PORT_MASTER 0
|
|
|
|
/*
|
|
* As of 2018-11-27 the default for both is 60 bytes. These larger values allow
|
|
* for reflashing of ITE EC chips over I2C
|
|
* (https://issuetracker.google.com/79684405) in reasonably speedy fashion. If
|
|
* the EC firmware defaults are ever raised significantly, consider removing
|
|
* these overrides.
|
|
*
|
|
* As of 2018-11-27 the actual maximum write size supported by the I2C-over-USB
|
|
* protocol is (1<<12)-1, and the maximum read size supported is
|
|
* (1<<15)-1. However compile time assertions require that these values be
|
|
* powers of 2 after overheads are included. Thus, the write limit set here
|
|
* /should/ be (1<<12)-4 and the read limit should be (1<<15)-6, however those
|
|
* ideal limits are not actually possible because servo_micro lacks sufficient
|
|
* spare memory for them. With symmetrical limits, the maximum that currently
|
|
* fits is (1<<11)-4 write limit and (1<<11)-6 read limit, leaving 1404 bytes of
|
|
* RAM available.
|
|
*
|
|
* However even with a sufficiently large write value here, the maximum that
|
|
* actually works as of 2018-12-03 is 255 bytes. Additionally, ITE EC firmware
|
|
* image verification requires exactly 256 byte reads. Thus the only useful
|
|
* powers-of-2-minus-overhead limits to set here are (1<<9)-4 writes and
|
|
* (1<<9)-6 reads, leaving 6012 bytes of RAM available, down from 7356 bytes of
|
|
* RAM available with the default 60 byte limits.
|
|
*/
|
|
#undef CONFIG_USB_I2C_MAX_WRITE_COUNT
|
|
#undef CONFIG_USB_I2C_MAX_READ_COUNT
|
|
#define CONFIG_USB_I2C_MAX_WRITE_COUNT ((1<<9) - 4)
|
|
#define CONFIG_USB_I2C_MAX_READ_COUNT ((1<<9) - 6)
|
|
|
|
/*
|
|
* Allow dangerous commands all the time, since we don't have a write protect
|
|
* switch.
|
|
*/
|
|
#define CONFIG_SYSTEM_UNLOCKED
|
|
|
|
#ifndef __ASSEMBLER__
|
|
|
|
/* Timer selection */
|
|
#define TIM_CLOCK32 2
|
|
|
|
#include "gpio_signal.h"
|
|
|
|
/* USB string indexes */
|
|
enum usb_strings {
|
|
USB_STR_DESC = 0,
|
|
USB_STR_VENDOR,
|
|
USB_STR_PRODUCT,
|
|
USB_STR_SERIALNO,
|
|
USB_STR_VERSION,
|
|
USB_STR_I2C_NAME,
|
|
USB_STR_USART4_STREAM_NAME,
|
|
USB_STR_CONSOLE_NAME,
|
|
USB_STR_USART3_STREAM_NAME,
|
|
USB_STR_USART2_STREAM_NAME,
|
|
USB_STR_UPDATE_NAME,
|
|
|
|
USB_STR_COUNT
|
|
};
|
|
|
|
#endif /* !__ASSEMBLER__ */
|
|
#endif /* __CROS_EC_BOARD_H */
|