361 lines
9.8 KiB
C
361 lines
9.8 KiB
C
/* Copyright 2018 The Chromium OS Authors. All rights reserved.
|
|
* Use of this source code is governed by a BSD-style license that can be
|
|
* found in the LICENSE file.
|
|
*/
|
|
|
|
/* Ampton/Apel board-specific configuration */
|
|
|
|
#include "adc.h"
|
|
#include "adc_chip.h"
|
|
#include "button.h"
|
|
#include "charge_state.h"
|
|
#include "common.h"
|
|
#include "cros_board_info.h"
|
|
#include "driver/accel_kionix.h"
|
|
#include "driver/accelgyro_bmi160.h"
|
|
#include "driver/ppc/sn5s330.h"
|
|
#include "driver/sync.h"
|
|
#include "driver/tcpm/it83xx_pd.h"
|
|
#include "driver/tcpm/ps8xxx.h"
|
|
#include "driver/usb_mux/it5205.h"
|
|
#include "extpower.h"
|
|
#include "gpio.h"
|
|
#include "hooks.h"
|
|
#include "i2c.h"
|
|
#include "intc.h"
|
|
#include "keyboard_scan.h"
|
|
#include "lid_switch.h"
|
|
#include "motion_sense.h"
|
|
#include "power.h"
|
|
#include "power_button.h"
|
|
#include "spi.h"
|
|
#include "switch.h"
|
|
#include "system.h"
|
|
#include "tablet_mode.h"
|
|
#include "tcpci.h"
|
|
#include "temp_sensor.h"
|
|
#include "thermistor.h"
|
|
#include "uart.h"
|
|
#include "usb_mux.h"
|
|
#include "usbc_ppc.h"
|
|
#include "util.h"
|
|
|
|
static uint8_t sku_id;
|
|
|
|
static void ppc_interrupt(enum gpio_signal signal)
|
|
{
|
|
if (signal == GPIO_USB_C0_PD_INT_ODL)
|
|
sn5s330_interrupt(0);
|
|
else if (signal == GPIO_USB_C1_PD_INT_ODL)
|
|
sn5s330_interrupt(1);
|
|
}
|
|
|
|
int ppc_get_alert_status(int port)
|
|
{
|
|
if (port == 0)
|
|
return gpio_get_level(GPIO_USB_C0_PD_INT_ODL) == 0;
|
|
else
|
|
return gpio_get_level(GPIO_USB_C1_PD_INT_ODL) == 0;
|
|
}
|
|
|
|
#include "gpio_list.h" /* Must come after other header files. */
|
|
|
|
/******************************************************************************/
|
|
/* USB-C MUX Configuration */
|
|
|
|
#define USB_PD_PORT_ITE_0 0
|
|
#define USB_PD_PORT_ITE_1 1
|
|
|
|
static int tune_mux(int port);
|
|
|
|
struct usb_mux ampton_usb_muxes[CONFIG_USB_PD_PORT_COUNT] = {
|
|
[USB_PD_PORT_ITE_0] = {
|
|
/* Use PS8751 as mux only */
|
|
.port_addr = MUX_PORT_AND_ADDR(
|
|
I2C_PORT_USBC0, PS8751_I2C_ADDR1_FLAGS),
|
|
.flags = USB_MUX_FLAG_NOT_TCPC,
|
|
.driver = &ps8xxx_usb_mux_driver,
|
|
.hpd_update = &ps8xxx_tcpc_update_hpd_status,
|
|
.board_init = &tune_mux,
|
|
},
|
|
[USB_PD_PORT_ITE_1] = {
|
|
/* Use PS8751 as mux only */
|
|
.port_addr = MUX_PORT_AND_ADDR(
|
|
I2C_PORT_USBC1, PS8751_I2C_ADDR1_FLAGS),
|
|
.flags = USB_MUX_FLAG_NOT_TCPC,
|
|
.driver = &ps8xxx_usb_mux_driver,
|
|
.hpd_update = &ps8xxx_tcpc_update_hpd_status,
|
|
.board_init = &tune_mux,
|
|
}
|
|
};
|
|
|
|
/* Some external monitors can't display content normally (eg. ViewSonic VX2880).
|
|
* We need to turn the mux for monitors to function normally.
|
|
*/
|
|
static int tune_mux(int port)
|
|
{
|
|
/* Auto EQ disabled, compensate for channel lost up to 3.6dB */
|
|
mux_write(port, PS8XXX_REG_MUX_DP_EQ_CONFIGURATION, 0x98);
|
|
/* DP output swing adjustment +15% */
|
|
mux_write(port, PS8XXX_REG_MUX_DP_OUTPUT_CONFIGURATION, 0xc0);
|
|
|
|
return EC_SUCCESS;
|
|
}
|
|
/******************************************************************************/
|
|
/* ADC channels */
|
|
const struct adc_t adc_channels[] = {
|
|
/* Vbus C0 sensing (10x voltage divider). PPVAR_USB_C0_VBUS */
|
|
[ADC_VBUS_C0] = {.name = "VBUS_C0",
|
|
.factor_mul = 10 * ADC_MAX_MVOLT,
|
|
.factor_div = ADC_READ_MAX + 1,
|
|
.shift = 0,
|
|
.channel = CHIP_ADC_CH13},
|
|
/* Vbus C1 sensing (10x voltage divider). SUB_EC_ADC */
|
|
[ADC_VBUS_C1] = {.name = "VBUS_C1",
|
|
.factor_mul = 10 * ADC_MAX_MVOLT,
|
|
.factor_div = ADC_READ_MAX + 1,
|
|
.shift = 0,
|
|
.channel = CHIP_ADC_CH14},
|
|
/* Convert to raw mV for thermistor table lookup */
|
|
[ADC_TEMP_SENSOR_AMB] = {.name = "TEMP_AMB",
|
|
.factor_mul = ADC_MAX_MVOLT,
|
|
.factor_div = ADC_READ_MAX + 1,
|
|
.shift = 0,
|
|
.channel = CHIP_ADC_CH3},
|
|
/* Convert to raw mV for thermistor table lookup */
|
|
[ADC_TEMP_SENSOR_CHARGER] = {.name = "TEMP_CHARGER",
|
|
.factor_mul = ADC_MAX_MVOLT,
|
|
.factor_div = ADC_READ_MAX + 1,
|
|
.shift = 0,
|
|
.channel = CHIP_ADC_CH5},
|
|
};
|
|
BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT);
|
|
|
|
const struct temp_sensor_t temp_sensors[] = {
|
|
[TEMP_SENSOR_BATTERY] = {.name = "Battery",
|
|
.type = TEMP_SENSOR_TYPE_BATTERY,
|
|
.read = charge_get_battery_temp,
|
|
.action_delay_sec = 1},
|
|
[TEMP_SENSOR_AMBIENT] = {.name = "Ambient",
|
|
.type = TEMP_SENSOR_TYPE_BOARD,
|
|
.read = get_temp_3v3_51k1_47k_4050b,
|
|
.idx = ADC_TEMP_SENSOR_AMB,
|
|
.action_delay_sec = 5},
|
|
[TEMP_SENSOR_CHARGER] = {.name = "Charger",
|
|
.type = TEMP_SENSOR_TYPE_BOARD,
|
|
.read = get_temp_3v3_13k7_47k_4050b,
|
|
.idx = ADC_TEMP_SENSOR_CHARGER,
|
|
.action_delay_sec = 1},
|
|
};
|
|
BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT);
|
|
|
|
/* Motion sensors */
|
|
/* Mutexes */
|
|
static struct mutex g_lid_mutex;
|
|
static struct mutex g_base_mutex;
|
|
|
|
const mat33_fp_t lid_standard_ref = {
|
|
{ 0, FLOAT_TO_FP(-1), 0},
|
|
{ FLOAT_TO_FP(1), 0, 0},
|
|
{ 0, 0, FLOAT_TO_FP(1)}
|
|
};
|
|
|
|
const mat33_fp_t base_standard_ref = {
|
|
{ 0, FLOAT_TO_FP(-1), 0},
|
|
{ FLOAT_TO_FP(1), 0, 0},
|
|
{ 0, 0, FLOAT_TO_FP(1)}
|
|
};
|
|
|
|
const mat33_fp_t gyro_standard_ref = {
|
|
{ 0, FLOAT_TO_FP(-1), 0},
|
|
{ FLOAT_TO_FP(1), 0, 0},
|
|
{ 0, 0, FLOAT_TO_FP(1)}
|
|
};
|
|
|
|
/* sensor private data */
|
|
static struct kionix_accel_data g_kx022_data;
|
|
static struct bmi160_drv_data_t g_bmi160_data;
|
|
|
|
/* Drivers */
|
|
struct motion_sensor_t motion_sensors[] = {
|
|
[LID_ACCEL] = {
|
|
.name = "Lid Accel",
|
|
.active_mask = SENSOR_ACTIVE_S0_S3,
|
|
.chip = MOTIONSENSE_CHIP_KX022,
|
|
.type = MOTIONSENSE_TYPE_ACCEL,
|
|
.location = MOTIONSENSE_LOC_LID,
|
|
.drv = &kionix_accel_drv,
|
|
.mutex = &g_lid_mutex,
|
|
.drv_data = &g_kx022_data,
|
|
.port = I2C_PORT_SENSOR,
|
|
.i2c_spi_addr_flags = KX022_ADDR1_FLAGS,
|
|
.rot_standard_ref = &lid_standard_ref,
|
|
.default_range = 4, /* g */
|
|
.config = {
|
|
/* EC use accel for angle detection */
|
|
[SENSOR_CONFIG_EC_S0] = {
|
|
.odr = 10000 | ROUND_UP_FLAG,
|
|
},
|
|
/* Sensor on for lid angle detection */
|
|
[SENSOR_CONFIG_EC_S3] = {
|
|
.odr = 10000 | ROUND_UP_FLAG,
|
|
},
|
|
},
|
|
},
|
|
[BASE_ACCEL] = {
|
|
.name = "Base Accel",
|
|
.active_mask = SENSOR_ACTIVE_S0_S3,
|
|
.chip = MOTIONSENSE_CHIP_BMI160,
|
|
.type = MOTIONSENSE_TYPE_ACCEL,
|
|
.location = MOTIONSENSE_LOC_BASE,
|
|
.drv = &bmi160_drv,
|
|
.mutex = &g_base_mutex,
|
|
.drv_data = &g_bmi160_data,
|
|
.port = I2C_PORT_SENSOR,
|
|
.i2c_spi_addr_flags = BMI160_ADDR0_FLAGS,
|
|
.rot_standard_ref = &base_standard_ref,
|
|
.default_range = 4, /* g */
|
|
.min_frequency = BMI160_ACCEL_MIN_FREQ,
|
|
.max_frequency = BMI160_ACCEL_MAX_FREQ,
|
|
.config = {
|
|
/* EC use accel for angle detection */
|
|
[SENSOR_CONFIG_EC_S0] = {
|
|
.odr = 13000 | ROUND_UP_FLAG,
|
|
.ec_rate = 100 * MSEC,
|
|
},
|
|
/* Sensor on for angle detection */
|
|
[SENSOR_CONFIG_EC_S3] = {
|
|
.odr = 10000 | ROUND_UP_FLAG,
|
|
.ec_rate = 100 * MSEC,
|
|
},
|
|
},
|
|
},
|
|
[BASE_GYRO] = {
|
|
.name = "Base Gyro",
|
|
.active_mask = SENSOR_ACTIVE_S0_S3,
|
|
.chip = MOTIONSENSE_CHIP_BMI160,
|
|
.type = MOTIONSENSE_TYPE_GYRO,
|
|
.location = MOTIONSENSE_LOC_BASE,
|
|
.drv = &bmi160_drv,
|
|
.mutex = &g_base_mutex,
|
|
.drv_data = &g_bmi160_data,
|
|
.port = I2C_PORT_SENSOR,
|
|
.i2c_spi_addr_flags = BMI160_ADDR0_FLAGS,
|
|
.default_range = 1000, /* dps */
|
|
.rot_standard_ref = &gyro_standard_ref,
|
|
.min_frequency = BMI160_GYRO_MIN_FREQ,
|
|
.max_frequency = BMI160_GYRO_MAX_FREQ,
|
|
},
|
|
[VSYNC] = {
|
|
.name = "Camera VSYNC",
|
|
.active_mask = SENSOR_ACTIVE_S0,
|
|
.chip = MOTIONSENSE_CHIP_GPIO,
|
|
.type = MOTIONSENSE_TYPE_SYNC,
|
|
.location = MOTIONSENSE_LOC_CAMERA,
|
|
.drv = &sync_drv,
|
|
.default_range = 0,
|
|
.min_frequency = 0,
|
|
.max_frequency = 1,
|
|
},
|
|
};
|
|
|
|
unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors);
|
|
|
|
static int board_is_convertible(void)
|
|
{
|
|
/* SKU IDs of Ampton & unprovisioned: 1, 2, 3, 4, 255 */
|
|
return sku_id == 1 || sku_id == 2 || sku_id == 3 || sku_id == 4
|
|
|| sku_id == 255;
|
|
}
|
|
|
|
static int board_with_ar_cam(void)
|
|
{
|
|
/* SKU ID of Ampton with AR Cam: 3, 4 */
|
|
return sku_id == 3 || sku_id == 4;
|
|
}
|
|
|
|
static void board_update_sensor_config_from_sku(void)
|
|
{
|
|
if (board_is_convertible()) {
|
|
motion_sensor_count = ARRAY_SIZE(motion_sensors);
|
|
/* Enable Base Accel interrupt */
|
|
gpio_enable_interrupt(GPIO_BASE_SIXAXIS_INT_L);
|
|
} else {
|
|
motion_sensor_count = 0;
|
|
gmr_tablet_switch_disable();
|
|
|
|
/* Base accel is not stuffed, don't allow line to float */
|
|
gpio_set_flags(GPIO_BASE_SIXAXIS_INT_L,
|
|
GPIO_INPUT | GPIO_PULL_DOWN);
|
|
}
|
|
|
|
if (board_with_ar_cam()) {
|
|
/* Enable interrupt from camera */
|
|
gpio_enable_interrupt(GPIO_WFCAM_VSYNC);
|
|
} else {
|
|
/* Camera isn't stuffed, don't allow line to float */
|
|
gpio_set_flags(GPIO_WFCAM_VSYNC, GPIO_INPUT | GPIO_PULL_DOWN);
|
|
}
|
|
}
|
|
|
|
static void board_customize_usbc_mux(uint32_t board_version)
|
|
{
|
|
if (board_version > 0) {
|
|
/* not proto, override the mux setting */
|
|
memcpy(usb_muxes, ampton_usb_muxes, sizeof(ampton_usb_muxes));
|
|
}
|
|
}
|
|
|
|
/* Read CBI from i2c eeprom and initialize variables for board variants */
|
|
static void cbi_init(void)
|
|
{
|
|
uint32_t val;
|
|
|
|
if (cbi_get_sku_id(&val) != EC_SUCCESS)
|
|
return;
|
|
sku_id = val;
|
|
ccprints("SKU: %d", sku_id);
|
|
|
|
board_update_sensor_config_from_sku();
|
|
|
|
if (cbi_get_board_version(&val) != EC_SUCCESS)
|
|
return;
|
|
ccprints("Board version: %d", val);
|
|
board_customize_usbc_mux(val);
|
|
}
|
|
DECLARE_HOOK(HOOK_INIT, cbi_init, HOOK_PRIO_INIT_I2C + 1);
|
|
|
|
void board_hibernate_late(void)
|
|
{
|
|
/*
|
|
* Set KSO/KSI pins to GPIO input function to disable keyboard scan
|
|
* while hibernating. This also prevent leakage current caused
|
|
* by internal pullup of keyboard scan module.
|
|
*/
|
|
gpio_set_flags_by_mask(GPIO_KSO_H, 0xff, GPIO_INPUT);
|
|
gpio_set_flags_by_mask(GPIO_KSO_L, 0xff, GPIO_INPUT);
|
|
gpio_set_flags_by_mask(GPIO_KSI, 0xff, GPIO_INPUT);
|
|
}
|
|
|
|
void board_overcurrent_event(int port, int is_overcurrented)
|
|
{
|
|
/* TODO(b/78344554): pass this signal upstream once hardware reworked */
|
|
cprints(CC_USBPD, "p%d: overcurrent!", port);
|
|
}
|
|
|
|
#ifndef TEST_BUILD
|
|
/* This callback disables keyboard when convertibles are fully open */
|
|
void lid_angle_peripheral_enable(int enable)
|
|
{
|
|
/*
|
|
* If the lid is in tablet position via other sensors,
|
|
* ignore the lid angle, which might be faulty then
|
|
* disable keyboard.
|
|
*/
|
|
if (tablet_get_mode())
|
|
enable = 0;
|
|
if (board_is_convertible())
|
|
keyboard_scan_enable(enable, KB_SCAN_DISABLE_LID_ANGLE);
|
|
}
|
|
#endif
|