gnuboot/website/README

== Introduction ==
This directory contains both the website in pages/ and build code to
easily build and deploy the GNU Boot website with very few commands.

== Dependencies ==

If you don't want to install Guix just to test the website, you will
need to install the following dependencies:

* autoconf
* automake
* coreutils
* gawk
* git
* graphviz
* grep
* gzip
* lighttpd
* make
* pandoc
* sed
* tar

$ ./autogen.sh
$ ./configure --disable-guix
$ make serve

And if you want to use Guix instead you only need the following
dependencies instead:

* autoconf
* automake
* coreutils
* guix
* make
* tar

For making sure that the build doesn't take days, you will also need
to make sure that bordeaux.guix.gnu.org is in the list of substitutes
(binary packages servers).

This is needed because some older Guix packages (like the ones on
Trisquel 11 or PureOS) don't have bordeaux enabled while installation
through the guix-install.sh instead have it enabled if you enable
substitutes (binary packages), and without it Guix will start to build
haskell (which is a dependency of pandoc) and this takes a few days to
complete on a ThinkPad X200.

If your Guix installation is recent enough it should already have it
and the following command should print 'bordeaux.guix.gnu.org is
enabled':
$ guix repl force-bordeaux-substitute.scm check

If instead you need to add it, it will print 'bordeaux.guix.gnu.org is
disabled'.

You can add bordeaux.guix.gnu.org with the following command:
$ guix pull
$ sudo guix archive --authorize < ~/.config/guix/current/share/guix/bordeaux.guix.gnu.org.pub

You will also need to make it possible for the build system to check
if it is enabled as some people might want to bulid everything
themselves for security reasons, so we don't use bordeaux if it is not
already authorized:
$ sudo chmod +r /etc/guix/acl

Once bordeaux is enabled you can use the following commands to build
the website:
$ ./autogen.sh
$ ./configure
$ make serve

== Testing the website ==

Here's how to deploy the website in a local webserver:
$ ./autogen.sh
$ ./configure
$ make serve

If you don't use Guix, remember to do ./configure --disable-guix instead.

Then you can point a browser to http://localhost:8086/software/gnuboot/web/ or
to http://localhost:PORT/software/gnuboot/web/ if you changed the port through
./configure options.

The GNU Boot website build system takes care of some of the
dependencies for you (for instance the static website generator that
is not packaged in any distributions) so you have less work to do to
install or use them on your side.

If you want to test your own modifications to the dependencies of this
build code, you either need to use the configure options to use
external repositories that have your modifications, or you could also
modify the build.sh script to use different git repositories and/or
revisions.

== Deployment on https://gnu.org/software/gnuboot/ ==

The deployment to https://gnu.org/software/gnuboot/ uses rsync. As
gnu.org machine is behind a firewall, so you need to workaround
that.

A way to do that is to get a shell account on fencepost.gnu.org, and
use SSH to forward the connection to gnu.org. This can be done with
something like that in your SSH configuration:

    Host fencepost.gnu.org
       User USERNAME

    Host gnu.org
       User wwwcvs
       ProxyJump fencepost.gnu.org

In the example above you will need to adjust the fencepost USERNAME,
and modify it to suit your SSH setup if needed (for instance if you
use keys in different locations, etc). Of course, you'll have to get
access to gnu.org ssh server too.

See https://www.gnu.org/software/README.accounts.html for more details
about Fencepost accounts, the SSH fingerprints, etc.

For gnu.org, it's easier if you use an ED25519 key for gnu.org as I
have the fingerprints below. See [1] for other options.

To check that everything is setup you can then SSH into gnu.org:
    $ ssh gnu.org
    The authenticity of host '[127.0.0.1]:2224 ([127.0.0.1]:2224)' can't be established.
    ED25519 key fingerprint is SHA256:pmCf0NrBzSSYfg6DdgmlMzPWZzGpXXcPEz6LP1+o5Jc.
    This host key is known by the following other names/addresses:
        ~/.ssh/known_hosts:306: [127.0.0.1]:4444
    Are you sure you want to continue connecting (yes/no/[fingerprint])?

You can then confirm by pasting the fingerprint like that[2]:
    Are you sure you want to continue connecting (yes/no/[fingerprint])? SHA256:pmCf0NrBzSSYfg6DdgmlMzPWZzGpXXcPEz6LP1+o5Jc
    Warning: Permanently added '[127.0.0.1]:2224' (ED25519) to the list of known hosts.

Note that it is normal for the connection to gnu.org to block at this
point. You can exit it with the Ctrl+D or Ctrl+C key combinations.

At this point everything is setup.

To deploy the website, use the following commands from the website
directory:
    $ ./autogen.sh
    $ ./configure
    $ make publish

Then you can point a browser to https://gnu.org/software/gnuboot/web/

References:
-----------
[1]If you want to use RSA the easiest way is probably to contact the
   FSF system administrator that will install your key on #fsfsys and
   also ask that person for the server fingerprint. In that case it
   would be a good idea to also contribute a patch to add the
   fingerprint here.
[2]The 'SHA256:pmCf0NrBzSSYfg6DdgmlMzPWZzGpXXcPEz6LP1+o5Jc'
   fingerprint was confirmed to me the 24 October 2023 on the #fsfsys
   IRC channel on liberachat by Ian Kelling, a system administrator
   that has access to the gnu.org machine: "18:07 < iank> i see that
   SHA256:pmCf0NrBzSSYfg6DdgmlMzPWZzGpXXcPEz6LP1+o5Jc exists on the
   server".


== License ==
This project is free software:
- For the files that are in website/pages and the the site.cfg file in
  the same directory than this README see website/pages/license.md for
  the license.
- For all the other files in the same directory than this README, you
  can redistribute them and/or modify them under the terms of the GNU
  General Public License as published by the Free Software Foundation,
  either version 3 of the License, or (at your option) any later
  version.