2021-05-18 14:21:48 +02:00
|
|
|
---
|
|
|
|
|
title: Read/write 25XX NOR flash via SPI protocol
|
|
|
|
|
x-toc-enable: true
|
|
|
|
|
...
|
|
|
|
|
|
|
|
|
|
This guide will teach you how to use various tools for externally reprogramming
|
|
|
|
|
a 25xx NOR flash via SPI protocol. This is the most common type of flash IC for
|
|
|
|
|
computers that coreboot runs on. Almost every system currently supported by
|
|
|
|
|
Libreboot uses this type of boot flash; the only exception is ASUS KFSN4-DRE,
|
|
|
|
|
which uses LPC flash in a PLCC32 socket, which you can simply hot-swap after
|
|
|
|
|
booting the vendor firmware, and then flash internally. Simple!
|
|
|
|
|
|
|
|
|
|
We will be using
|
|
|
|
|
the [flashrom](https://flashrom.org/Flashrom) software which is written to
|
|
|
|
|
dump, erase and rewrite these flash chips.
|
|
|
|
|
|
|
|
|
|
Libreboot currently documents how to use these SPI programmers:
|
|
|
|
|
|
|
|
|
|
* Raspberry Pi (RPi)
|
|
|
|
|
* BeagleBone Black (BBB)
|
|
|
|
|
|
|
|
|
|
Many other SPI programmers exist. More of them will be documented on this page,
|
|
|
|
|
at a date in the future.
|
|
|
|
|
|
|
|
|
|
Most systems in Libreboot have to be re-flashed externally, using instructions
|
|
|
|
|
on this and similar guides, the first time you flash. However, on all currently
|
|
|
|
|
supported systems, it's possible that you can re-flash *internally* when
|
|
|
|
|
Libreboot is running.
|
|
|
|
|
|
|
|
|
|
*Internal* flashing means that the host CPU on your system can re-program the
|
|
|
|
|
SPI flash, using an on-board SPI programmer (which all boards have). You do this
|
|
|
|
|
from GNU+Linux, with flashrom.
|
|
|
|
|
|
|
|
|
|
*This* guide that you're reading now is for using an *external* programmer. It
|
|
|
|
|
is called *external* because it's not the *internal* one on your mainboard.
|
|
|
|
|
|
|
|
|
|
Do not use CH341A!
|
|
|
|
|
==================
|
|
|
|
|
|
|
|
|
|
NOR flashes on Libreboot systems run on 3.3V DC, and this includes data lines.
|
|
|
|
|
CH341A has 5V logic levels on data lines, which will damage your SPI flash and
|
|
|
|
|
also the southbridge that it's connected to, plus anything else that it's
|
|
|
|
|
connected to.
|
|
|
|
|
|
|
|
|
|
These ch341a programmers are unfortunately very popular. DO NOT use it unless
|
|
|
|
|
you have fixed the issue. You CAN fix it so that the data lines are 3.3v, if
|
|
|
|
|
you follow the notes here:
|
|
|
|
|
|
|
|
|
|
<https://www.eevblog.com/forum/repair/ch341a-serial-memory-programmer-power-supply-fix/>
|
|
|
|
|
|
|
|
|
|
In practise, most people will not fix their ch341a and instead just risk it,
|
|
|
|
|
so no documentation will be provided for ch341a on this website. It is best
|
|
|
|
|
to discourage use of that device.
|
|
|
|
|
|
|
|
|
|
In case it's not clear:
|
|
|
|
|
|
|
|
|
|
Please do not buy the ch341a! It is incorrectly engineered for the purpose of
|
|
|
|
|
ROM flashing on systems with 3.3v SPI (which is most coreboot systems). DO NOT
|
|
|
|
|
USE IT! This issue still isn't fixed by the manufacturer, and it doesn't look
|
|
|
|
|
like they will ever fix it.
|
|
|
|
|
|
|
|
|
|
If you see someone talking about CH341A, please direct them to this page and
|
|
|
|
|
tell them why the CH341A is bad.
|
|
|
|
|
|
|
|
|
|
Identify which flash type you have
|
|
|
|
|
==================================
|
|
|
|
|
|
|
|
|
|
In all of them, a dot or marking shows pin 1 (in the case of WSON8, pad 1).
|
|
|
|
|
|
|
|
|
|
Use the following photos and then look at your board. When you've figured out
|
|
|
|
|
what type of chip you have, use that knowledge and the rest of this guide, to
|
|
|
|
|
accomplish your goal, which is to read from and/or write to the boot flash.
|
|
|
|
|
|
|
|
|
|
SOIC8
|
|
|
|
|
-----
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SOIC16
|
|
|
|
|
------
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SOIC8 and SOIC16 are the most common types, but there are others:
|
|
|
|
|
|
|
|
|
|
WSON8
|
|
|
|
|
-----
|
|
|
|
|
|
|
|
|
|
It will be like this on an X200S or X200 Tablet:\
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
On T400S, it is in this location near the RAM:\
|
|
|
|
|
\
|
|
|
|
|
NOTE: in this photo, the chip has been replaced with SOIC8
|
|
|
|
|
|
|
|
|
|
DIP8
|
|
|
|
|
----
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Software configuration
|
|
|
|
|
======================
|
|
|
|
|
|
|
|
|
|
BeagleBone Black (BBB)
|
|
|
|
|
----------------------
|
|
|
|
|
|
|
|
|
|
SSH into your BeagleBone Black. It is assumed that you are running Debian 9 on
|
|
|
|
|
your BBB. You will run `flashrom` from your BBB.
|
|
|
|
|
|
|
|
|
|
NOTE: This section is out of date, because it is written for Debian 9 (running
|
|
|
|
|
on the BBB)
|
|
|
|
|
|
|
|
|
|
Run the following commands as root to enable spidev:
|
|
|
|
|
|
|
|
|
|
config-pin P9.17 spi_cs
|
|
|
|
|
config-pin P9.18 spi
|
|
|
|
|
config-pin P9.21 spi
|
|
|
|
|
config-pin P9.22 spi_sclk
|
|
|
|
|
|
|
|
|
|
Verify that the spidev devices now exist:
|
|
|
|
|
|
|
|
|
|
ls /dev/spidev*
|
|
|
|
|
|
|
|
|
|
Output:
|
|
|
|
|
|
|
|
|
|
/dev/spidev1.0 /dev/spidev1.1 /dev/spidev2.0 /dev/spidev2.1
|
|
|
|
|
|
|
|
|
|
Now the BBB is ready to be used for flashing. The following systemd service
|
|
|
|
|
file can optionally be enabled to make this persistent across reboots.
|
|
|
|
|
|
|
|
|
|
```
|
|
|
|
|
[Unit]
|
|
|
|
|
Description=Enable SPI function on pins
|
|
|
|
|
|
|
|
|
|
[Service]
|
|
|
|
|
Type=oneshot
|
|
|
|
|
ExecStart=config-pin P9.17 spi_cs
|
|
|
|
|
ExecStart=config-pin P9.18 spi
|
|
|
|
|
ExecStart=config-pin P9.21 spi
|
|
|
|
|
ExecStart=config-pin P9.22 spi_sclk
|
|
|
|
|
RemainAfterExit=yes
|
|
|
|
|
|
|
|
|
|
[Install]
|
|
|
|
|
WantedBy=multi-user.target
|
|
|
|
|
```
|
|
|
|
|
|
|
|
|
|
Now test flashrom:
|
|
|
|
|
|
|
|
|
|
./flashrom -p linux_spi:dev=/dev/spidev1.0,spispeed=512
|
|
|
|
|
|
|
|
|
|
It is important to use `spispeed=512` or a lower number such as 256 or 128,
|
|
|
|
|
because otherwise the BBB will be quite unstable.
|
|
|
|
|
|
|
|
|
|
Example output:
|
|
|
|
|
|
|
|
|
|
Calibrating delay loop... OK.
|
|
|
|
|
No EEPROM/flash device found.
|
|
|
|
|
Note: flashrom can never write if the flash chip isn't found automatically.
|
|
|
|
|
|
|
|
|
|
This means that it's working (the clip isn't connected to any flash
|
|
|
|
|
chip, so the error is fine).
|
|
|
|
|
|
|
|
|
|
Caution about BBB
|
|
|
|
|
-----------------
|
|
|
|
|
|
|
|
|
|
BeagleBone Black is not recommended, because it's very slow and unstable for
|
|
|
|
|
SPI flashing, and nowadays much better options exist. We used to mainly
|
|
|
|
|
recommend the BBB, because of the fact that it can be used with entirely Free
|
2021-07-28 06:04:22 +02:00
|
|
|
Software on it, but nowadays there are superior options.
|
2021-05-18 14:21:48 +02:00
|
|
|
|
2021-07-28 06:04:22 +02:00
|
|
|
TODO: document other SPI flashers
|
2021-05-18 14:21:48 +02:00
|
|
|
|
|
|
|
|
Rasberry Pi (RPi)
|
|
|
|
|
-----------------
|
|
|
|
|
|
|
|
|
|
SSH into your Raspberry Pi. You will run `flashrom` from your Raspberry Pi.
|
|
|
|
|
|
|
|
|
|
You must configure `spidev` on your Raspberry Pi. This is a special driver in
|
|
|
|
|
the Linux kernel; technically, the driver name is `spi-bcm2835`.
|
|
|
|
|
|
|
|
|
|
This page has info:\
|
|
|
|
|
<https://www.raspberrypi.org/documentation/hardware/raspberrypi/spi/README.md>
|
|
|
|
|
|
|
|
|
|
In your Raspberry Pi, which we assume you're running the latest Raspbian version
|
|
|
|
|
on, do this:
|
|
|
|
|
|
|
|
|
|
sudo raspi-config
|
|
|
|
|
|
|
|
|
|
Under the Interface section, you can enable SPI.
|
|
|
|
|
|
|
|
|
|
The device for communicating via SPI as at `/dev/spidev0.0`
|
|
|
|
|
|
2021-05-21 16:50:20 +02:00
|
|
|
Caution about RPi
|
|
|
|
|
-----------------
|
|
|
|
|
|
|
|
|
|
Basically, the Raspbian project, now called Raspberry Pi OS, put in their repo
|
|
|
|
|
an update that added a new "trusted" repository, which just so happened to be
|
|
|
|
|
a Microsoft software repository. They seem to have done this for VS Code, but
|
|
|
|
|
the problem here is that it gave Microsoft free reign to define whatever
|
|
|
|
|
dependencies they liked (as per apt-get rules), and every time you updated,
|
|
|
|
|
you would be pinging Microsoft servers. Do you think that is strange?
|
|
|
|
|
|
|
|
|
|
Microsoft shouldn't have *any* access to your GNU+Linux system! This was the
|
|
|
|
|
commit that Raspbian added to their distro, which added this what should rightly
|
2021-05-21 16:53:19 +02:00
|
|
|
be called a security vulnerability, intentionally:
|
2021-05-21 16:50:20 +02:00
|
|
|
|
|
|
|
|
* <https://github.com/RPi-Distro/raspberrypi-sys-mods/commit/655cad5aee6457b94fc2336b1ff3c1104ccb4351>
|
|
|
|
|
|
|
|
|
|
They then removed it, after a public backlash, via the following commits:
|
|
|
|
|
|
|
|
|
|
* <https://github.com/RPi-Distro/raspberrypi-sys-mods/commit/ed96790e6de281bc393b575c38aa8071ce39b555>
|
|
|
|
|
* <https://github.com/RPi-Distro/raspberrypi-sys-mods/commit/4d1afece91008f3787495b520ac03b53fef754c6>
|
|
|
|
|
|
|
|
|
|
For now, Raspbian / Raspberry Pi OS (which is based on Debian) should be safe,
|
|
|
|
|
but this whole episode proves that the distro can no longer be trusted to
|
|
|
|
|
respect its users. Therefore, it's now on the [tasks page](../../tasks/)
|
|
|
|
|
a TODO entry for recommending and documenting alternative GNU+Linux distros
|
|
|
|
|
on the Raspberry Pi, for the purposes of SPI flashing.
|
|
|
|
|
|
2021-05-18 14:21:48 +02:00
|
|
|
Install flashrom
|
|
|
|
|
----------------
|
|
|
|
|
|
|
|
|
|
If you're using a BBB or RPi, you will do this while SSH'd into those.
|
|
|
|
|
|
|
|
|
|
Flashrom is the software that you will use, for dumping, erasing and rewriting
|
|
|
|
|
the contents of your NOR flash.
|
|
|
|
|
|
|
|
|
|
In the Libreboot build system, from the Git repository, you can download and
|
|
|
|
|
install flashrom. Do this after downloading the
|
|
|
|
|
[lbmk Git repository](https://notabug.org/libreboot/lbmk):
|
|
|
|
|
|
|
|
|
|
cd lbmk
|
|
|
|
|
sudo ./build dependencies ubuntu2004
|
|
|
|
|
./download flashrom
|
|
|
|
|
./build module flashrom
|
|
|
|
|
|
|
|
|
|
If the `ubuntu2004` script complains about missing dependencies, just modify
|
|
|
|
|
the script and remove those dependencies. The script is located
|
|
|
|
|
at `resources/scripts/build/dependencies/ubuntu2004` and it is written for
|
|
|
|
|
Ubuntu 20.04, but it should work fine in other GNU+Linux distributions that use
|
|
|
|
|
the `apt-get` package manager.
|
|
|
|
|
|
|
|
|
|
A `flashrom/` directory will be present, with a `flashrom` executable inside
|
|
|
|
|
of it. If you got an error about missing package when running the dependencies
|
|
|
|
|
command above, tweak `resources/scripts/build/dependencies/ubuntu2004`. That
|
|
|
|
|
script downloads and installs build dependencies in apt-get and it is intended
|
|
|
|
|
for use on x86-64 systems running Ubuntu 20.04, but it should work in Raspbian
|
|
|
|
|
on the Raspberry Pi.
|
|
|
|
|
|
|
|
|
|
Alternatively, you may download flashrom directly from upstream
|
|
|
|
|
at <https://flashrom.org/Flashrom>
|
|
|
|
|
|
|
|
|
|
If you're flashing a Macronix flashchip on a ThinkPad X200, you will want to
|
|
|
|
|
use a special patched version of flashrom, which you can download here:
|
|
|
|
|
<https://vimuser.org/hackrom.tar.xz> - patched source code is available, and a
|
|
|
|
|
binary is also available that you can simply run. Pass the `--workaround-mx`
|
|
|
|
|
argument in flashrom. This mitigates stability issues.
|
|
|
|
|
|
|
|
|
|
If you downloaded the flashrom source code directly, you can go into the
|
|
|
|
|
directory and simply type `make`. In the Libreboot build system, build
|
|
|
|
|
dependencies are documented in script located
|
|
|
|
|
at `resources/scripts/build/dependencies/` which you can install
|
|
|
|
|
using the `apt-get` software.
|
|
|
|
|
|
|
|
|
|
How to use flashrom
|
|
|
|
|
===================
|
|
|
|
|
|
|
|
|
|
Read past these sections, further down this page, to learn about specific chip
|
|
|
|
|
types and how to wire them.
|
|
|
|
|
|
|
|
|
|
Reading
|
|
|
|
|
-------
|
|
|
|
|
|
|
|
|
|
Before flashing a new ROM image, it is highly advisable that you dump the
|
|
|
|
|
current chip contents to a file.
|
|
|
|
|
|
|
|
|
|
Run this command to see if 25xx flash is detected, with your RPi properly
|
|
|
|
|
wired.
|
|
|
|
|
|
|
|
|
|
sudo ./flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=32768
|
|
|
|
|
|
|
|
|
|
For BBB, you must use a lower speed and a different device path:
|
|
|
|
|
|
|
|
|
|
sudo ./flashrom -p linux_spi:dev=/dev/spidev1.0,spispeed=512
|
|
|
|
|
|
|
|
|
|
On BBB, never use a speed higher than `spispeed=512`. In some cases, you may
|
|
|
|
|
even need to go as low as `spispeed=128`. The BBB is highly unstable and
|
|
|
|
|
unreliable for SPI flashing. When you're reading, take multiple dumps and
|
|
|
|
|
verify that the checksums match, before you flash. You may have to flash your
|
|
|
|
|
chip several times!
|
|
|
|
|
|
|
|
|
|
NOTE: On some systems, higher speeds will be unstable. On those systems, try
|
|
|
|
|
lower speed like `spispeed=4096` or even `spispeed=2048` which should, in most
|
|
|
|
|
cases, work just fine but it will obviously be slower. The `spispeed=32768`
|
|
|
|
|
setting works just fine on most setups if you use short wires, within 10cm.
|
|
|
|
|
|
|
|
|
|
If flash chip is detected you may try reading (dumping) the flash contents now,
|
|
|
|
|
or you can try flashing it with a new ROM.
|
|
|
|
|
|
|
|
|
|
Dump it like so (RPi):
|
|
|
|
|
|
|
|
|
|
sudo ./flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=32768 -r dump.bin
|
|
|
|
|
|
|
|
|
|
For BBB, do this:
|
|
|
|
|
|
|
|
|
|
sudo ./flashrom -p linux_spi:dev=/dev/spidev1.0,spispeed=512 -r dump.bin
|
|
|
|
|
|
|
|
|
|
It is advisable to take a *2nd* dump, e.g. `dump2.bin`, and then check sha1sum:
|
|
|
|
|
|
|
|
|
|
sha1sum dump*.bin
|
|
|
|
|
|
|
|
|
|
If the checksums match, it indicates that you have a good dump. If they do not,
|
|
|
|
|
check your wiring. Wires should be within 10cm length for best stability, and
|
|
|
|
|
they should all be the same length (3.3V VCC and GND wires can be longer).
|
|
|
|
|
|
|
|
|
|
This advice is *especially* applicable to the BBB, which is highly unreliable.
|
|
|
|
|
|
|
|
|
|
Writing
|
|
|
|
|
-------
|
|
|
|
|
|
|
|
|
|
Next, run this command (RPi):
|
|
|
|
|
|
|
|
|
|
sudo ./flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=32768 -w /path/to/libreboot.rom
|
|
|
|
|
|
|
|
|
|
If using BBB:
|
|
|
|
|
|
|
|
|
|
sudo ./flashrom -p linux_spi:dev=/dev/spidev1.0,spispeed=512 -w /path/to/libreboot.rom
|
|
|
|
|
|
|
|
|
|
If using BBB, you may have to use a lower speed than 512. You may also have to
|
|
|
|
|
re-flash several times before it works fully.
|
|
|
|
|
|
|
|
|
|
Again, use a lower `spispeed` value if you need to, for stability.
|
|
|
|
|
|
|
|
|
|
Once that command outputs the following, the flash has completed
|
|
|
|
|
successfully. If not, just flash again.
|
|
|
|
|
|
|
|
|
|
Reading old flash chip contents... done.
|
|
|
|
|
Erasing and writing flash chip... Erase/write done.
|
|
|
|
|
Verifying flash... VERIFIED.
|
|
|
|
|
|
|
|
|
|
If it says "VERIFIED" or says that the chip contents are identical to the
|
|
|
|
|
requested image, then the chip is properly flashed.
|
|
|
|
|
|
|
|
|
|
Hardware configuration
|
|
|
|
|
======================
|
|
|
|
|
|
|
|
|
|
Refer to the above guidance about software configuration. The following advice
|
|
|
|
|
will teach you how to wire each type of flash chip.
|
|
|
|
|
|
|
|
|
|
WARNINGS
|
|
|
|
|
--------
|
|
|
|
|
|
|
|
|
|
Do not connect a 3.3V DC power source until your chip is otherwise properly
|
|
|
|
|
wired. For instance, do not connect a test clip that has 3.3V DC attached.
|
|
|
|
|
|
|
|
|
|
Do not *disconnect* your chip from the flasher until you've disconnected or
|
|
|
|
|
turned off the 3.3V DC power source.
|
|
|
|
|
|
|
|
|
|
BE CAREFUL that you are indeed supplying 3.3V DC to the chip. All SPI flashes
|
|
|
|
|
on all currently supported Libreboot hardware run on 3.3V DC and logic at that
|
|
|
|
|
level too.
|
|
|
|
|
|
|
|
|
|
It is important to CHECK that you are running on the current voltage, when you
|
|
|
|
|
do anything with these chips. Lower than 3.3V won't damage anything, but higher
|
|
|
|
|
will fry your chip (on most chips, the tolerated voltage range is between 2.7V
|
|
|
|
|
and 3.6V, but 3.3V is the most ideal level).
|
|
|
|
|
|
|
|
|
|
DO NOT connect more than 1 DC power source to your flash chip either!
|
|
|
|
|
Mixing voltages like that can easily cause damage to your equipment, and to
|
|
|
|
|
your chip/mainboard.
|
|
|
|
|
|
|
|
|
|
MISO/MOSI/CS/CLK lines
|
|
|
|
|
----------------------
|
|
|
|
|
|
|
|
|
|
You may want to add 47ohm series resistors on these lines, when flashing the
|
|
|
|
|
chips. Only do it on those lines (NOT the 3.3V or GND lines). This provides
|
|
|
|
|
some protection from over-current. On Intel platforms, the SPI flash is usually
|
|
|
|
|
connected via such resistors, directly to the Southbridge chipset.
|
|
|
|
|
|
|
|
|
|
ISP programming and VCC diode
|
|
|
|
|
-----------------------------
|
|
|
|
|
|
|
|
|
|
ISP means in-system programming. It's when you flash a chip that is already
|
|
|
|
|
mounted to the mainboard of your computer that you wish to install Libreboot
|
|
|
|
|
on.
|
|
|
|
|
|
|
|
|
|
It may be beneficial to modify the mainboard so that the SPI flash is powered
|
|
|
|
|
(on the VCC pin) through a diode, but please note: a diode will cause a voltage
|
|
|
|
|
drop. The tolerated range for VCC on these chips is 2.7V to 3.6V DC. If you do
|
|
|
|
|
this, please also ensure that the WP and HOLD pins are still held to a high
|
|
|
|
|
logic state; each via their own resistor (1K to 10K ohms) connected to the
|
|
|
|
|
*same* 3.3V DC source going through the diode.
|
|
|
|
|
|
|
|
|
|
The reason is simple: on most systems, the flash shares a common 3.3V DC rail
|
|
|
|
|
with many other components on the board, which draw a lot of current. Further,
|
|
|
|
|
if you accidentally provide too much voltage or cause an overcurrent, you could
|
|
|
|
|
fry those other components but if there is diode protection, you'll only fry
|
|
|
|
|
the boot flash (and it is very easy to replace, if you have good soldering
|
|
|
|
|
skills).
|
|
|
|
|
|
|
|
|
|
When you've placed the diode, ensure that VCC on the chip is isolated from all
|
|
|
|
|
other components on that board, which share the same 3.3V DC rail. Further,
|
|
|
|
|
ensure that the pull-up resistors for WP/HOLD are *only* connected to the side
|
|
|
|
|
of the diode that has continuity with the VCC pin (this is important because if
|
|
|
|
|
they're not, they won't be held high while doing ISP flashing, even if they're
|
|
|
|
|
still held high when the mainboard is fully powered on).
|
|
|
|
|
|
|
|
|
|
Furthermore: ensure that the SPI flash is operating at 2.7 to 3.6V when fully
|
|
|
|
|
powered on, after installing the diode.
|
|
|
|
|
|
|
|
|
|
If it's a desktop/workstation/server board (not a laptop), you could de-solder
|
|
|
|
|
the SOIC8/WSON8 if it uses that, and replace with an IC socket (for SOIC8,
|
|
|
|
|
WSON8 or DIP8, whatever you want), because then you could easily just insert
|
|
|
|
|
the flash into a breadboard when flashing.
|
|
|
|
|
|
|
|
|
|
TODO: Make a page on libreboot.org, showing how to do this on all mainboards
|
|
|
|
|
supported by Libreboot.
|
|
|
|
|
|
|
|
|
|
GPIO pins on BeagleBone Black (BBB)
|
|
|
|
|
-----------------------------------
|
|
|
|
|
|
|
|
|
|
Use this image for reference when connecting the pomona to the BBB:
|
|
|
|
|
<https://beagleboard.org/Support/bone101#headers> (D0 = MISO or connects
|
|
|
|
|
to MISO).
|
|
|
|
|
|
|
|
|
|
On that page, look at the *P9 header*. It is what you will use to wire up your
|
|
|
|
|
chip for flashing.
|
|
|
|
|
|
|
|
|
|
GPIO pins on Raspberry Pi (RPi)
|
|
|
|
|
-------------------------------
|
|
|
|
|
|
|
|
|
|
Diagram of the 26 GPIO Pins of the Raspberry Pi Model B (for the Model
|
|
|
|
|
B+ with 40 pins, start counting from the right and leave 14 pins):
|
|
|
|
|
|
|
|
|
|
 
|
|
|
|
|
|
|
|
|
|
Use this as a reference for the other sections in this page, seen below:
|
|
|
|
|
|
|
|
|
|
SOIC8/DIP8/WSON8 wiring diagram
|
|
|
|
|
-------------------------------
|
|
|
|
|
|
|
|
|
|
Refer to this diagram:
|
|
|
|
|
|
|
|
|
|
Pin \# 25xx signal RPi(GPIO) BBB(P9 header)
|
|
|
|
|
------ ----------- ---------- --------------
|
|
|
|
|
1 CS 24 17
|
|
|
|
|
2 MISO 21 21
|
|
|
|
|
3 *not used* *not used* *not used*
|
|
|
|
|
4 GND 25 1
|
|
|
|
|
5 MOSI 19 18
|
|
|
|
|
6 CLK 23 22
|
|
|
|
|
7 *not used* *not used* *not used*
|
|
|
|
|
8 3.3V 1 3
|
|
|
|
|
|
|
|
|
|
On your SOIC8, there will be a dot in one of the corners. The dot is pin 1.
|
|
|
|
|
|
|
|
|
|
NOTE: pins 3 and 7 are WP/HOLD pins. If flashing a chip on a breadboard, please
|
|
|
|
|
use pull-up resistors on those (see notes below), and decoupling capacitor on
|
|
|
|
|
pin 8 (VCC).
|
|
|
|
|
|
|
|
|
|
NOTE: On X60/T60 thinkpads, don't connect pin 8. Instead, plug in your the PSU
|
|
|
|
|
to the charging port on your mainboard, but do not power on the mainboard. This
|
|
|
|
|
will provide a stable 3.3V voltage, with adequate current levels. On those
|
|
|
|
|
laptops, this is necessary because the flash shares a common 3.3V DC rail with
|
|
|
|
|
many other ICs that all draw quite a lot of current.
|
|
|
|
|
|
|
|
|
|
SOIC16 wiring diagram (Raspberry Pi)
|
|
|
|
|
------------------------------------
|
|
|
|
|
|
|
|
|
|
RPi GPIO header:\
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
BBB P9 header:\
|
|
|
|
|
<https://beagleboard.org/static/images/cape-headers.png>
|
|
|
|
|
|
|
|
|
|
Refer to this diagram:
|
|
|
|
|
|
|
|
|
|
Pin \# 25xx signal RPi(GPIO) BBB(P9 header)
|
|
|
|
|
-------- -------------- ----------- --------------
|
|
|
|
|
1 *not used* *not used* *not used*
|
|
|
|
|
2 3.3V 1 3
|
|
|
|
|
3 *not used* *not used* *not used*
|
|
|
|
|
4 *not used* *not used* *not used*
|
|
|
|
|
5 *not used* *not used* *not used*
|
|
|
|
|
6 *not used* *not used* *not used*
|
|
|
|
|
7 CS\# 24 17
|
|
|
|
|
8 MISO 21 21
|
|
|
|
|
9 *not used* *not used* *not used*
|
|
|
|
|
10 GND 25 1
|
|
|
|
|
11 *not used* *not used* *not used*
|
|
|
|
|
12 *not used* *not used* *not used*
|
|
|
|
|
13 *not used* *not used* *not used*
|
|
|
|
|
14 *not used* *not used* *not used*
|
|
|
|
|
15 MOSI 19 18
|
|
|
|
|
16 SCLK 23 22
|
|
|
|
|
|
|
|
|
|
Refer to the RPi GPIO guide above, on this page.
|
|
|
|
|
|
|
|
|
|
On your SOIC16, there will be a dot in one of the corners. The dot is pin 1.
|
|
|
|
|
|
|
|
|
|
NOTE: pins 1 and 9 are WP/HOLD pins. If flashing a chip on a breadboard, please
|
|
|
|
|
use pull-up resistors on those (see notes below), and decoupling capacitor on
|
|
|
|
|
pin 2 (VCC).
|
|
|
|
|
|
|
|
|
|
Pull-up resistors and decoupling capacitors
|
|
|
|
|
-------------------------------------------
|
|
|
|
|
|
|
|
|
|
**Do this for chips mounted to a breadboard. Ignore this section if you're
|
|
|
|
|
flashing a chip that is already soldered to a mainboard.**
|
|
|
|
|
|
|
|
|
|
This section is only relevant if you're flashing a new chip that is not yet
|
|
|
|
|
mounted to a mainboard. You need pull-up resistors on the WP and HOLD pins,
|
|
|
|
|
and decoupling capacitors on the VCC pin. If the chip is already mounted to a
|
|
|
|
|
board, whether soldered or in a socket, these capacitors and resistors will
|
|
|
|
|
probably already exist on the board and you can just flash it without pulling
|
|
|
|
|
WP/HOLD high, and without capacitors(just connect your external 3.3V DC power
|
|
|
|
|
source).
|
|
|
|
|
|
|
|
|
|
The best way is as follows:
|
|
|
|
|
|
|
|
|
|
* Insert the DIP8 IC into a breadboard (2.54mm holes), if it's DIP8
|
|
|
|
|
* Insert WSON8 into a WSON8 socket and put on a breadboard, if WSON8
|
|
|
|
|
* Insert SOIC8 into a SOIC8 socket and put on a broadboard, if SOIN8
|
|
|
|
|
* Wire an SPI flasher, using 2.54mm dupont leads, to the breadboard, using
|
|
|
|
|
the correct wiring (see link to SPI flashing guides below)
|
|
|
|
|
|
|
|
|
|
SOIC8/WSON8/DIP8: pin 3 and 7 must be held to a high logic state, which means
|
|
|
|
|
that each pin
|
|
|
|
|
has its own pull-up resistor to VCC (from the 3.3v voltage plane that pin 8
|
|
|
|
|
connects to); anything from 1Kohm to 10Kohm will do. When you're flashing a chip
|
|
|
|
|
that's already on a laptop/desktop/server mainboard, pin 3 and 7 are likely
|
|
|
|
|
already held high, so you don't need to bother.
|
|
|
|
|
|
|
|
|
|
SOIC8/WSON8/DIP8: pin 8, which is 3.3v VCC, will already have decoupling capacitors on it
|
|
|
|
|
if the chip is on a mainboard, but lone chip flashing means that these capacitors
|
|
|
|
|
do not exist. A capacitor passes AC but blocks DC. Due to electromagnetic
|
|
|
|
|
indunctance, and RF noise from high-speed switching ICs, a DC voltage line isn't
|
|
|
|
|
actually straight (when viewed on an oscilloscope), but actually has low voltage
|
|
|
|
|
AC mixed in; on a particularly noisy line under high load, noise of around 300mV
|
|
|
|
|
or more is common. To smooth out that noise, you wire capacitors from the DC
|
|
|
|
|
line to ground, with the side of the capacitor on VCC as close to the IC's VCC
|
|
|
|
|
pin as possible. We recommend that you use ceramic capacitors for this purpose.
|
|
|
|
|
The recommended capacitors for this are: 100nF and 4.7uF ceramic capacitors.
|
|
|
|
|
Electrolytic capacitors are inferior for this, because they have higher ESR
|
|
|
|
|
(ceramic capacitors have super low ESR, which is very good for decoupling).
|
|
|
|
|
|
|
|
|
|
The result of using a decoupling capacitor is that some of the noise on the DC
|
|
|
|
|
line is filtered to ground, making the DC signal much cleaner/straighter (when
|
|
|
|
|
seen on an oscilloscope).
|
|
|
|
|
|
|
|
|
|
SOIC16: same as above, but use a SOIC16 socked on a breadboard. On SOIC16,
|
|
|
|
|
WP/HOLD are not pin 3/7 like above, but instead pins 1 and 9, so wire your
|
|
|
|
|
pull-up resistors on those. 3.3v VCC on SOIC16 is pin 2, so wire your
|
|
|
|
|
decoupling capacitors up on that.
|
|
|
|
|
|
|
|
|
|
SOIC8/WSON8/DIP8/SOIC16 not mounted to a mainboard
|
|
|
|
|
--------------------------------------------------
|
|
|
|
|
|
|
|
|
|
If your system has lower capacity SPI flash, you can upgrade. On *most* systems,
|
|
|
|
|
SPI flash is memory mapped and the maximum (in practise) that you can use is a
|
|
|
|
|
16MiB chip. For example, KGPE-D16 and KCMA-D8 mainboards in Libreboot have
|
|
|
|
|
2MiB flash by default, but you can easily upgrade these. Another example is the
|
|
|
|
|
ThinkPad X200S, X200 Tablet and T400S, all of which have WSON8 where the best
|
|
|
|
|
course of action is to replace it with a SOIC8 flash chip.
|
|
|
|
|
|
|
|
|
|
In all such cases, flashing a new chip should be done using a breadboard, not
|
|
|
|
|
a test clip. You will use 2.54mm dupont leads to connect your Raspberry Pi.
|
|
|
|
|
For data lines, make sure that all wires are the same length, and about 10cm
|
|
|
|
|
in length (don't use longer lengths than this).
|
|
|
|
|
|
|
|
|
|
Some advice:
|
|
|
|
|
|
|
|
|
|
* DIP8: Strong choice is Winbond W25Q128FVIQ. It is a direct drop-in replacement
|
|
|
|
|
* SOIC8 is possible: Winbond W25Q128FVSIG is a strong choice.
|
|
|
|
|
* DIP8 using adapter and SOIC8 is also possible. Use a 208-mil 1.27mm SOP8/SOIC8
|
|
|
|
|
to DIP8 adapter PCB with a
|
|
|
|
|
2.54mm 4-pin header on each side (square pins), then you can slot that in as
|
|
|
|
|
though it were a normal P-DIP 8 IC. This page shows a perfect example:
|
|
|
|
|
<https://coolcomponents.co.uk/products/soic-to-dip-adapter-8-pin>
|
|
|
|
|
* The above SOP8/DIP8 adapter is actually what we recommend, if you're going
|
|
|
|
|
that route. It's made by Sparkfun and widely available; you don't have to buy
|
|
|
|
|
from that particular website. The part number is: BOB-13655
|
|
|
|
|
* If you use a SOP/DIP adapter with a SOIC8 IC, you'll have to solder it
|
|
|
|
|
obviously. K tip is a nice choice for soldering ICs like these. Use good
|
|
|
|
|
flux and 60/40 leaded solder (or 63/37), none of that Rohs lead-free crap.
|
|
|
|
|
|
|
|
|
|
If you go for a SOIC8, mounted it to the SOP to DIP adapter (208mil 1.27mm one)
|
|
|
|
|
and solder 2.54mm headers to it. You could put the 2.54mm pins in a breadboard,
|
|
|
|
|
then solder the chip to the adapter PCB and mount that to the pins on the
|
|
|
|
|
breadboard, to keep it aligned, and solder that. Whith the PCB on the pins, and
|
|
|
|
|
the pins in the breadboard, push the pins inwards a little bit.
|
|
|
|
|
|
|
|
|
|
This is for a new SOIC8 chip, but you can get sockets similar to the one in the
|
|
|
|
|
video, but for WSON8. Sometimes they are called DFN8 or QFN8 sockets. Get one
|
|
|
|
|
that is 1.27mm pitch.
|
|
|
|
|
|
|
|
|
|
If you're flashing/dumping a lone WSON8, get a WSON8/QFN8/DFN8 socket (1.27mm
|
|
|
|
|
pitch) and mount it to a breadboard for flashing. If your mainboard's landing
|
|
|
|
|
pads for the flash IC can take a SOIC8, we recommend that you use a SOIC8
|
|
|
|
|
instead because a test clip is possible later on when you wish to re-flash it,
|
|
|
|
|
however you may be dealing with a board where replacing existing WSON8 with
|
|
|
|
|
SOIC8 is desirable; in that case, you might still want to dump the contents of
|
|
|
|
|
the original WSON8.
|
|
|
|
|
|
|
|
|
|
Here is a SOIC8 in a socket, mounted to a breadboard, for flashing:\
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Here is a photo of a DIP8 IC:\
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Here is a photo of a SOIC8 in 1.27mm 208mil SOP to DIP adapter:\
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Here is a video of that SOIC8 (in socket) being flashed:\
|
2021-07-19 18:00:09 +02:00
|
|
|
<https://vid.puffyan.us/watch?v=tguch_iPBZQ>\
|
2021-05-18 14:21:48 +02:00
|
|
|
NOTE: DIP8 and WSON8-in-socket, and SOIC16-in-socket, are basically the same,
|
|
|
|
|
just adapt accordingly.
|
|
|
|
|
|
|
|
|
|
If you're replacing a DIP8 but using SOIC8 on an adapter, solder it to the
|
|
|
|
|
adapter first, then insert 2.54mm headers (square pins) into a breadboard to
|
|
|
|
|
keep them aligned. Put the SOIC8 on the PCB, onto the pins, and push the pins
|
|
|
|
|
inwards a little bit, and solder that. Alternatively to the breadboard, you
|
|
|
|
|
can just put the 2.54mm pins directly in the DIP8 socket and mount the SOIC8 +
|
|
|
|
|
adapter onto that, and solder that. Use quality rosin flux (not acid based)
|
|
|
|
|
and good 60/40 or 63/37 leaded solder (don't use lead-free):
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SOIC8/SOIC16 soldered to a mainboard
|
|
|
|
|
------------------------------------
|
|
|
|
|
|
|
|
|
|
This is an example of *in-system programming* or *ISP* for short.
|
|
|
|
|
|
|
|
|
|
SOIC8:\
|
2021-07-29 06:54:25 +02:00
|
|
|
Pomona 5250 is a SOIC8 test clip. There are others available, but this is the
|
2021-05-18 14:21:48 +02:00
|
|
|
best one. Use that. Use the SOIC8 diagram (see above) to wire up your Raspberry
|
|
|
|
|
Pi.
|
|
|
|
|
Your mainboard likely already pulls WP/HOLD (pins 3 and 7) high, so don't
|
|
|
|
|
connect these. 3.3v VCC on SOIC8's pin 8 probably already has decoupling
|
|
|
|
|
capacitors on the mainboard, so just hook that up without using a capacitor.
|
|
|
|
|
|
|
|
|
|
SOIC16:\
|
2021-07-29 06:54:25 +02:00
|
|
|
Pomona 5252 is a SOIC16 test clip. There are others available, but this is the
|
2021-05-18 14:21:48 +02:00
|
|
|
best one. Use that. Use the SOIC16 diagram (see above) to wire up your Raspberry
|
|
|
|
|
Pi. WP/HOLD pins are pins 1 and 9, and likely already held high, so no pull-up
|
|
|
|
|
resistors needed. You do not need a decoupling capacitor for pin 2 (VCC) either
|
|
|
|
|
because the mainboard will already have one.
|
|
|
|
|
|
|
|
|
|
Here is an example of a test clip connected for SOIC16:\
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
And here is an example photo for SOIC8:\
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DIP8 soldered to the mainboard
|
|
|
|
|
------------------------------
|
|
|
|
|
|
|
|
|
|
It is extremely cursed for DIP8 to be soldered directly to the mainboard. It is
|
|
|
|
|
usually mounted to a socket.
|
|
|
|
|
|
|
|
|
|
The pins are large enough that you can just use test hooks to wire up your chip
|
|
|
|
|
for flashing. You might want to de-solder the chip, using a solder vacuum
|
|
|
|
|
(extractor) tool, and then you can install a socket in its place. You can then
|
|
|
|
|
insert the DIP8 IC into the socket.
|
|
|
|
|
|
|
|
|
|
In the Libreboot project, we have never heard of a board where the DIP8 is
|
|
|
|
|
directly soldered. It is almost always mounted in a socket.
|
|
|
|
|
|
|
|
|
|
Your DIP8 IC has the same pinout as a SOIC8 IC.
|
|
|
|
|
|
|
|
|
|
Replace WSON8 IC with SOIC8
|
|
|
|
|
---------------------------
|
|
|
|
|
|
|
|
|
|
You *can* connect a SOIC8 test clip, but you will struggle to get good
|
|
|
|
|
connections and it will be extremely unreliable. DO NOT solder to the pads of
|
|
|
|
|
the WSON8 directly; some people do this, but you shouldn't do it, because you
|
|
|
|
|
can easily damage the pads that way.
|
|
|
|
|
|
|
|
|
|
WSON8 has the same pinout as SOIC8, but it's a ball mounted QFN (quad flat
|
|
|
|
|
pack, no leads). There are no clips for it. Sometimes referred to as QFN8
|
|
|
|
|
|
|
|
|
|
On all currently supported Libreboot hardware, boards that have WSON8 can also
|
|
|
|
|
have a SOIC8 because the pads are long enough to accomodate either type of
|
|
|
|
|
chip.
|
|
|
|
|
|
|
|
|
|
A good choice of soldering iron would be a T12-D08 or T12-K tip, on a T12
|
|
|
|
|
soldering station. KSGER makes nice soldering stations:\
|
2021-07-19 18:00:09 +02:00
|
|
|
<https://vid.puffyan.us/watch?v=w0nZCK7B-0U>
|
2021-05-18 14:21:48 +02:00
|
|
|
|
|
|
|
|
The case on that KSGER station is not grounded by default, so you should
|
|
|
|
|
modify it to ground the case, in case of an electrical fault. This is for your
|
|
|
|
|
safety. This video shows how to do it:\
|
2021-07-19 18:00:09 +02:00
|
|
|
<https://vid.puffyan.us/watch?v=-6IZ_sBgw8I>
|
2021-05-18 14:21:48 +02:00
|
|
|
|
|
|
|
|
Use quality 60/40 or 63/37 lead+tin solder. Do not use lead-free! Lead-free is
|
|
|
|
|
not suitable for hobbyist use such as this. Use quality *rosin* flux. Fluxes
|
|
|
|
|
with an acid base should never be used. Amtech and MG Chemicals make good flux
|
|
|
|
|
pastes. Use it in a dispenser tube. Some of these fluxes will contain adapic
|
|
|
|
|
acid which has a low pH level, and it is simply used as a mild activator. So
|
|
|
|
|
long as you clean the flux afterwards, you should be fine.
|
|
|
|
|
|
|
|
|
|
Make sure to have a copper wire brush and a wet sponge handy. You wipe the iron
|
|
|
|
|
on the wire brush and tap it on the wet sponge(to remove oxides) to keep it
|
|
|
|
|
clean. Always clean your tip constantly. Also, after cleaning it, always re-tin
|
|
|
|
|
the tip with fresh solder, to prevent the tip from oxidizing!
|
|
|
|
|
|
|
|
|
|
Make sure to buy 99.9% isopropyl alcohol. Don't buy weaker solutions because
|
|
|
|
|
they contain water, and don't use other chemicals because most other chemicals
|
|
|
|
|
are corrosive. You use the isopropyl to clean the area you're soldering, before
|
|
|
|
|
soldering it, and then soak up the wet alcohol with a cloth. You will also use
|
|
|
|
|
it to clean off any flux that you used.
|
|
|
|
|
|
|
|
|
|
Use of flux is very important, to get a good solder joint, because it removes
|
|
|
|
|
oxides and prevents further oxidation during soldering, ensuring that the solder
|
|
|
|
|
flows properly, otherwise the solder will ball up and you won't get a good
|
|
|
|
|
joint.
|
|
|
|
|
|
|
|
|
|
In case you're not comfortable with soldering, we have some excellent videos
|
|
|
|
|
linked on the [FAQ page](../../faq.md) which you can watch.
|
|
|
|
|
|
|
|
|
|
Here is a video example for ThinkPad X200 Tablet:\
|
2021-07-19 18:00:09 +02:00
|
|
|
<https://vid.puffyan.us/watch?v=oUYHzOQXx80>\
|
2021-05-18 14:21:48 +02:00
|
|
|
(X200S and T400S also require this)
|
|
|
|
|
|
|
|
|
|
Alternatively, here are photos:
|
|
|
|
|
|
|
|
|
|
WSON8 IC:\
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Surround a large area around the chip with layers of kapton tape, and then
|
|
|
|
|
aluminium foil. This will act as a heat shield, to reduce the risk of re-flowing
|
|
|
|
|
other solder joints (which can make them turn into cold joints, and you risk
|
|
|
|
|
knocking them off of the board):\
|
|
|
|
|
\
|
|
|
|
|
Notice that the kapton+foil does not cover the chip itself, or the solder pads.
|
|
|
|
|
It's important that these are exposed to the heat.
|
|
|
|
|
|
|
|
|
|
Use a hot air rework station, set to about 330-340C. The reason for the higher
|
|
|
|
|
temperature is because air doesn't conduct heat as efficiently as an iron, so
|
|
|
|
|
you must use a higher temperature. You should put lots of rosin flux above the
|
|
|
|
|
IC. Do not hold the nozel too close to the board. The diameter of the nozel
|
|
|
|
|
should be slightly higher than the length of the chip. Apply even heat, at high
|
|
|
|
|
air flow.
|
|
|
|
|
|
|
|
|
|
While blasting the chip with hot air, hold the chip with tweezers but do not
|
|
|
|
|
use any real force. Do not try to forcefully pry off the chip. Simply hold the
|
|
|
|
|
chip with your tweezers, gently nudging it until it feels like the chip can
|
|
|
|
|
move freely. While in this state, the solder is fully melted and the chip can
|
|
|
|
|
be lifted off with ease.
|
|
|
|
|
|
|
|
|
|
If you're doing it correctly, the chip will come off within 1 minute, like so:\
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Add fresh solder to the pads, including the thermal pad:\
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Now wick it out using a copper braid, dunked in rosin flux:\
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ensure that all of the solder is removed:\
|
|
|
|
|
\
|
|
|
|
|
You will notice that one of the pads doesn't have all of the solder removed.
|
|
|
|
|
The pad on the top-left in this photo. This is intentional, to show you a
|
|
|
|
|
comparison for reference. The other pads are free of solder.
|
|
|
|
|
|
|
|
|
|
You *can* simply solder the chip unflashed, and flash it using a test clip.
|
|
|
|
|
Alternatively, you can put the SOIC8 in a socket on a breadboard, and flash it
|
|
|
|
|
before soldering it. If you wish to dump the contents of the WSON8, you can
|
|
|
|
|
put the removed WSON8 in a socket on a breadboard and dump it using your
|
|
|
|
|
SPI flasher.
|
|
|
|
|
|
|
|
|
|
Align the new SOIC8, and tack it in the corner pins. Then solder it fully. Use
|
|
|
|
|
lots of flux!\
|
|
|
|
|
\
|
|
|
|
|
A T12-D08 tip is being used in this photo, but a mini chisel, mini hoof or
|
|
|
|
|
knife (e.g. T12-K) tip would be ideal.
|
|
|
|
|
|
|
|
|
|
Ensure that all the joints are perfect. A good solder joint is shiny, and with
|
|
|
|
|
concave fillets where the solder has flowed. Observe:\
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
After you're done, use a soft bristle brush and 99.9% isopropyl alcohol to
|
|
|
|
|
break up the remaining flux, then soak up the flux using a cloth, while the
|
|
|
|
|
alcohol is still wet. 99.9% isopropyl is the best liquid to use, because it
|
|
|
|
|
evaporates quickly and it does not leave a corrosive residue.
|
|
|
|
|
|
|
|
|
|
-------------------------------------------------------------------------------
|
|
|
|
|
|
|
|
|
|
LICENSING
|
|
|
|
|
=========
|
|
|
|
|
|
|
|
|
|
This page is released under different copyright terms than most other pages
|
|
|
|
|
on this website.
|
|
|
|
|
|
|
|
|
|
This page and the photos on it are available under
|
|
|
|
|
[CC BY SA 4.0](https://creativecommons.org/licenses/by-sa/4.0/legalcode.txt)
|
|
|
|
|
Check the Git repository for history of who owns what part of the document.
|
|
|
|
|
|
|
|
|
|
Photos showing a BeagleBone Black are under the normal GNU Free Documentation
|
|
|
|
|
license like other pages and images on this website, or you can use them under
|
|
|
|
|
the CC-BY-SA 4.0 license if you wish (I, Leah Rowe, own all BBB photos shown
|
|
|
|
|
on this page, except for the one on the beaglebone website, and that one is
|
|
|
|
|
merely linked here, instead of being hosted on the av.libreboot.org server).
|
|
|
|
|
|
|
|
|
|
This version of the page is hosted in the `lbwww` git repository, with images
|
|
|
|
|
for it hosted in the `lbwww-img` repository. Images and this page were both
|
|
|
|
|
forked from the *old* Libreboot git repository, which was available here:
|
|
|
|
|
<https://notabug.org/libreboot/libreboot/> (you can still download it but this
|
|
|
|
|
repository is no longer worked on. You can find both the website and images
|
|
|
|
|
under the `www/` and/or `docs/` directory, in that repository)
|
