serial supprt.

git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1152 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

src/mainboard/via/epia/auto.c

@@ -28,6 +28,7 @@ void udelay(int usecs) {
 #define MAXIMUM_CONSOLE_LOGLEVEL 9
 #define DEFAULT_CONSOLE_LOGLEVEL 9
 
+#include "southbridge/via/vt8231/vt8231_early_serial.c"
 static void memreset_setup(void)
 {
 }
@@ -53,6 +54,7 @@ static void main(void)
 {
   /*	init_timer();*/
 
+	enable_vt8231_serial();
 	uart_init();
 	console_init();
 	

src/southbridge/via/vt8231/vt8231_early_serial.c

@@ -0,0 +1,71 @@
+/*
+ * Enable the serial evices on the VIA
+ */
+
+
+/* The base address is 0x15c, 0x2e, depending on config bytes */
+
+#define SIO_BASE 0x3f0
+#define SIO_DATA  SIO_BASE+1
+
+static void
+vt8231_writesuper(uint8_t reg, uint8_t val) {
+  outb(reg, SIO_BASE);
+  outb(val, SIO_DATA);
+}
+
+static void
+vt8231_writesiobyte(uint16_t reg, uint8_t val) {
+  outb(val, reg);
+}
+
+static void
+vt8231_writesioword(uint16_t reg, uint16_t val) {
+  outw(val, reg);
+}
+
+
+/* regs we use: 85, and the southbridge devfn is defined by the
+   mainboard
+ */
+
+static void
+enable_vt8231_serial(void) {
+  device_t dev;
+
+  dev = pci_locate_device(PCI_ID(0x1106,0x3065), 0);
+  
+  if (dev == PCI_DEV_INVALID) {
+    die("Serial controller not found\r\n");
+  }
+  
+
+  /* first, you have to enable the superio and superio config. 
+     put a 3 in devfn 38 reg 85
+  */
+  pci_write_config8(dev, 0x85, 3);
+  // now go ahead and set up com1. 
+  // set address
+  vt8231_writesuper(0xf4, 0xfe);
+  // enable serial out
+  vt8231_writesuper(0xf2, 7);
+  // That's it for the sio stuff.
+  //	movl	$SUPERIOCONFIG, %eax
+  //	movb	$9, %dl
+  //	PCI_WRITE_CONFIG_BYTE
+  // set up reg to set baud rate.
+  vt8231_writesiobyte(0x3fb, 0x80);
+  // Set 115 kb
+  vt8231_writesioword(0x3f8, 1);
+  // Set 9.6 kb
+  //	WRITESIOWORD(0x3f8, 12)
+  // now set no parity, one stop, 8 bits
+  vt8231_writesiobyte(0x3fb, 3);
+  // now turn on RTS, DRT
+  vt8231_writesiobyte(0x3fc, 3);
+  // Enable interrupts
+  vt8231_writesiobyte(0x3f9, 0xf);
+  // should be done. Dump a char for fun.
+  vt8231_writesiobyte(0x3f8, 48);
+  
+}