Along with upstream kernel for Retimer firmware upgrade, coreboot
provides DFPx under host router where each DFP has its PLD and DSM. The
DFPx's functions encapsulates power control through GPIO, PD
suspend/resume and modes setting for Retimer firmware update under NDA
scenario.
BUG=b:186521258
TEST=Booted to kernel and validated host router's DFPx properties after
decomposing SSDT table.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I81bef80729f6df57119f5523358620cb015e5406
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52712
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
HSBIAS_SENSE_EN configures HSBIAS output current sense through
the external 2.21-k resistor. HSBIAS_SENSE is hardware feature to reduce
the potential pop noise during the headset plug out slowly. But on some
platforms ESD voltage will affect it causing test to fail, especially
with CTIA headset type. For different hardware setups, a designer might
want to tweak default behavior.
Signed-off-by: Vitaly Rodionov <vitaly.rodionov@cirrus.corp-partner.google.com>
Change-Id: I87c6f01af1bdb5b1cb8e399191519598d7fbe9ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52981
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
List of changes:
1. Make the FSP notify phases name prior in comments section.
2. Fix discrepancies in FSP notify before and after postcode comments.
3. Add FSP notify postcode macros for after pci enumeration(0xa2)
and ready to boot(0xa3) call.
Change-Id: Ib4c825d5f1f31f80ad2a03ff5d6006daa7104d23
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52894
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add backlight support in sn65dsi86bridge through the AUX channel using
eDP DPCD registers, which is needed on the GOOGLE_HOMESTAR board.
Change-Id: Ie700080f1feabe2d3397c38088a64cff27bfbe55
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52663
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The SN65DSI86 eDP bridge supports two ways to read the EDID: for now
we've been using "direct mode", which works by basically making the
bridge I2C device listen to another chip address besides its own and
proxy all requests received there directly to the eDP AUX channel. The
great part about that mode is that it is super easy and hassle-free to
use. The not so great part about it is that it doesn't work: for EDID
extensions, the last byte (which happens to contain the checksum) is
somehow always read as zero. We presume this is a hardware bug in the
bridge part.
The other, much more annoying way is "indirect mode", where each byte
transmitted over the AUX channel has to be manually set up in the I2C
registers of the bridge, just like we're already doing with DPCD
transactions. Thankfully, we can reuse most of the DPCD code for this so
it's not a lot of extra code. It's a bit slower but not as much as you'd
expect (26ms instead of 18ms on my board), and the difference is not
very relevant compared to common total times for display init.
Also, some of the (previously unused) enum definitions for the AUX_CMD
mode field of the bridge had just been plain wrong for some reason, and
needed to be fixed to make this work.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I65f80193380d3c3841f9f5c26897ed672f45e15a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52959
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
None of the options accessed within coreboot is a string, and there are
no guarantees that the code works as intended with them. Given that the
current option API only supports integers for now, do not try to access
options whose type is 's' (string).
Change-Id: Ib67b126d972c6d55b77ea5ecfb862b4e9c766fe5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The CMOS option system does not support negative integers. Thus, retype
and rename the option API functions to reflect this.
Change-Id: Id3480e5cfc0ec90674def7ef0919e0b7ac5b19b3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
When using a hardware assisted root of trust measurement, like Intel
TXT/CBnT, the TPM init needs to happen inside the bootblock to form a
proper chain of trust.
Change-Id: Ifacba5d9ab19b47968b4f2ed5731ded4aac55022
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51923
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The only use case for FSP-T in coreboot is for 'Intel Bootguard'
support at the moment. Bootguard can do verification FSP-T but there
is no verification on whether the FSP found by walkcbfs_asm is the one
actually verified as an IBB by Bootguard. A fixed pointer needs to be
used.
TESTED on OCP/Deltalake, still boots.
Change-Id: I1ec8b238384684dccf39e5da902d426d3a32b9db
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
In order for short circuit protection and over current protection to work, the
debug mode needs to be turned off.
BUG=b:185749961
TEST=build and test
Signed-off-by: Ben Chuang <benchuanggli@gmail.com>
Change-Id: Iacfa3c668a52d1bae15fe82f1c614d0ebd93a957
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
If device is supported as a wake source, _S0W should be set to D3hot.
This ensures that the device is put into D3hot by the OSPM.
Power resource(PRIC) for the device is listed in both _PR0 and _PR3. Thus, it ensures that the OSPM does not turn off power resource when device is put into D0 and D3hot. Hence, it is capable of waking the system from D3hot state. However, if it is put into D3cold, then the power resource is turned off by the OSPM.
The devices we are currently looking at for touchscreen/touchpad
do not really support auxiliary power and so do not support wake from D3cold.
BUG=b:186070097
TEST=build and check device wake state _S0W set to 3 in ssdt table.
Change-Id: I34e4b2350875530d3337be700276bcc4fb1f810a
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Only SOC_INTEL_BRASWELL is using FSP1.1. It has too little CAR
available set up by FSP-T to have VBOOT_STARTS_IN_BOOTBLOCK and
therefore verstage is not possible either.
Change-Id: I54361c835055907c2a4414ec26a1495425d4ef09
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52785
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With the recent switch to SMM module loader v2, the size of the SMM for
module google/volteer increased to above 64K in size, and thus failed to
install the permanent SMM handler. Turns out, the devicetree is all
pulled into the SMM build because of elog, which calls
`pci_dev_is_wake_source`, and is the only user of `struct device` in
SMM. Changing this function to take a pci_devfn_t instead allows the
linker to remove almost the entire devicetree from SMM (only usage left
is when disabling HECI via SMM).
BUG=b:186661594
TEST=Verify loaded program size of `smm.elf` for google/volteer is
almost ~50% smaller.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4c39e5188321c8711d6479b15065e5aaedad8f38
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Inspired by discussion in CB:22822.
If I2C bus step response has not been measured, assume the layout to
have been designed with a minimal capacitance and SCL rise and fall
times of 0 ns. The calculations will add the required amount of
reference clocks for the host to drive SCL high or low, such that the
maximum bus frequency specification is met.
Change-Id: Icbafae22c83ffbc16c179fb5412fb4fd6b70813a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52723
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The procedure is identical for reads and writes. Factor it out.
Change-Id: I22b1d334270881734b34312f1fee01aa110a6db4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52636
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This driver uses the ACPI Device Property interface to generate
the required parameters into the _DSD table format expected by
the kernel
This was tested on the octopus/variants/fleex ainboard to ensure
that the SSDT contained the equivalent parameters that are provided
by the current DSDT object
Signed-off-by: Vitaly Rodionov <vitaly.rodionov@cirrus.corp-partner.google.com>
Change-Id: I7c3145b20a1ba743d91eb64b93cb001db3854c5d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
With this change, the type-unsafe {get,set}_option() API functions are
no longer used directly. The old API gets dropped in a follow-up.
Change-Id: Id3f3e172c850d50a7d2f348b1c3736969c73837d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52512
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We had the addrspace_32bit rdev in prog_loaders.c for a while to help
represent memory ranges as an rdev, and we've found it useful for a
couple of things that have nothing to do with program loading. This
patch moves the concept straight into commonlib/region.c so it is no
longer anchored in such a weird place, and easier to use in unit tests.
Also expand the concept to the whole address space (there's no real need
to restrict it to 32 bits in 64-bit environments) and introduce an
rdev_chain_mem() helper function to make it a bit easier to use. Replace
some direct uses of struct mem_region_device with this new API where it
seems to make sense.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie4c763b77f77d227768556a9528681d771a08dca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52533
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a new configuration low_power_probe to avoid camera privacy LED
blink during the boot.
Change-Id: I27d5c66fb380ae6cd76d04ee82b7736407dac1b0
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52189
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The selector component in Sound Open Firmware (SOF) can consume all the
mics and use the configuration in the Use Case Manager (UCM) to select
the right channel. Hence dmic select gpio configuration is optional.
BUG=b:182960979
TEST=Build and boot to OS in Guybrush. Ensure that the machine driver
ACPI object is populated without DMIC select GPIO.
Change-Id: Iba00b07c3656c487e33bab184fefee7037745e2d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52393
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
IPMI debug was extra spewy, so add a debug option as SPI and
other drivers have when they need to be debugged.
Change-Id: I788d67c242cac23bde9750aa3e95e3276c3f1fd7
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Traditionally, for each Intel platform using FSP, FSP-S has at some
point configured GPIOs differently than the mainboard configuration in
coreboot. This has resulted in various side-effects in coreboot,
payload and OS because of misconfigured GPIOs. On more recent Intel
platforms, a UPD `GpioOverride` is added that coreboot can use to
ensure that FSP does not touch any GPIO configuration.
This change adds a debug option `CHECK_GPIO_CONFIG_CHANGES` to fsp2_0
driver in coreboot that makes a platform callback `gpio_snapshot` to
snapshot GPIO configuration before making a call to FSP SiliconInit
and Notify phases. This snapshot is then compared against the GPIO
configuration using platform callback `gpio_verify_snapshot` after
returning from FSP. The callbacks are not added to romstage (FSP-M)
because mainboard configures all pads in ramstage.
This debug hook allows developers to dump information about any pads
that have a different configuration after call to FSP in ramstage. It
is useful to identify missed UPD configurations or bugs in FSP that
might not honor the UPDs set by coreboot.
This debug hook expects the platform to implement the callbacks
`gpio_snapshot` and `gpio_verify_snapshot`. These can be implemented
as part of the common GPIO driver for platforms using
FSP2.0+. Platforms that implement this support must select the config
`HAVE_GPIO_SNAPSHOT_VERIFY_SUPPORT` to make the debug config
`CHECK_GPIO_CONFIG_CHANGES` visible to user.
Proposal for the GPIO snapshot/verify support was discussed in the RFC
CB:50829.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I5326fc98b6eba0f8ba946842253b288c0d42c523
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50989
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This adds a driver for the TI TAS5825M smart amplifier [1].
The driver expects the mainboard using it to define tas5825m_setup(),
which uses the tas5825m_* functions to set configuration data. Each
mainboard may have very different configuration data, depending on
its audio hardware.
Tested on System76 addw1, bonw14, oryp5, and oryp6.
[1]: https://www.ti.com/product/TAS5825M
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Change-Id: I896e8f272f18e64bfc90f406e7d4163010800aaf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch changes the Intel MMA driver to use the new CBFS API.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Icc11d0c2a9ec1bd7a1d6af362f849dac16375433
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch ports the last remaining use of cbfs_boot_locate() in the
Intel FSP drivers to the new CBFS API. As a consequence, there is no
longer a reason for fsp_validate_component() to operate on rdevs, and
the function is simplified to take a direct void pointer and size to a
memory-mapping of the FSP blob instead.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If1f0239eefa4542e4d23f6e2e3ff19106f2e3c0d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52281
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
DPTF HIDs are different per-platform going forward, so refactor these
into SoC-specific structures which the DPTF driver can query at runtime
for platform-specific information.
Change-Id: I6307f9d28f4274b851323ad69180ff4ae35053da
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Rename the Kconfig parameter to more accurately reflect what it does.
TPM can be initialised in a different stage too, for instance with
VBOOT it is done in verstage.
Change-Id: Ic0126b356e8430c04c7c9fd46d4e20022a648738
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
This guards code accessing the vboot context which does not exist if
vboot starts after romstage.
Change-Id: I2a38daa00d6d18df9c5e22858530814e23bb3e00
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52157
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Add definitions to describe GPIOs in generated ACPI objects.
The method allow either write a GpioInt() or Interrupt() descriptor.
Signed-off-by: Seven Lee <wtli@nuvoton.com>
Change-Id: I37fec7b0b9324dbfb61b7a8bea80f45026c54409
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51922
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TPM_INIT depends on VBOOT but should also depend on
VENDORCODE_ELTAN_xBOOT.
Add dependency. TPM_INIT will be enable for measured boot only.
BUG = NA
TEST = Boot Facebook FB1701 with possible combinaties of VBOOT, measured
boot and eltan security.
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Change-Id: I03f8457731c73c653bd82b1042bda3fc2d797feb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
The only FSP 1.1 platform with MMA support is Skylake. As it now uses
Kaby Lake FSP 2.0, this code is no longer useful. Drop it.
Change-Id: I819c3152bdea0fdad629793d96136ef134429fbd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
The Intel FSP 2.0 driver contains a custom construct that basically
serves the same purpose as the new CBFS allocator concept: a callback
function to customize placement of a loaded CBFS file whose size is
initially unknown. This patch removes the existing implementation and
replaces it with a CBFS allocator.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I0b7b446a0d2af87ec337fb80ad54f2d404e69668
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Until now every AML package had to be closed using acpigen_pop_len().
This commit introduces set of package closing functions corresponding
with their opening function names. For example acpigen_write_if()
opens if-statement package, acpigen_write_if_end() closes it.
Now acpigen_write_else() closes previously opened acpigen_write_if(),
so acpigen_pop_len() is not required before it.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Icfdc3804cd93bde049cd11dec98758b3a639eafd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In pursuit of the eventual goal of removing cbfs_boot_locate() (and
direct rdev access) from CBFS APIs, this patch replaces all remaining
"simple" uses of the function call that can easily be replaced by the
newer APIs (like cbfs_load() or cbfs_map()). Some cases of
cbfs_boot_locate() remain that will be more complicated to solve.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Icd0f21e2fa49c7cc834523578b7b45b5482cb1a8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Since prog_locate() was eliminated, prog_rdev() only ever represents the
loaded program in memory now. Using the rdev API for this is unnecessary
if we know that the "device" is always just memory. This patch changes
it to be represented by a simple pointer and size. Since some code still
really wants this to be an rdev, introduce a prog_chain_rdev() helper to
translate back to that if necessary.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If7c0f1c5698fa0c326e23c553ea0fe928b25d202
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
IPMI OEM command set processor information has already been implemented
in u-root payload:
efdc3a30ec
Also this command has a higher chance to see BMC KCS timeout issue when
coreboot log level is 4, which can be avoided if this command is run at
a later stage such as LinuxBoot.
Signed-off-by: JingleHsuWiwynn <jingle_hsu@wiwynn.com>
Change-Id: If0081e5195cbd605e062723c197ac74343f79a13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51276
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that SAR support in VPD is deprecated in coreboot, there is no
need for a separate Kconfig `WIFI_SAR_CBFS` as the SAR table is only
supported as a CBFS file. This change drops the config `WIFI_SAR_CBFS`
from drivers/wifi/generic/Kconfig and its selection in
mb/google/.../Kconfig.
wifi_sar_defaults.hex is added to CBFS only if
CONFIG_WIFI_SAR_CBFS_FILEPATH is not empty because current mainboards
do not provide a default SAR file in
coreboot. Thus, CONFIG_WIFI_SAR_CBFS_FILEPATH is updated to have a
default value of "".
BUG=b:173465272
Cq-Depend: chromium:2757781
Change-Id: I0bb8f6e2511596e4503fe4d8c34439228ceaa3c7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch rewrites the last few users of prog_locate() to access CBFS
APIs directly and removes the call. This eliminates the double-meaning
of prog_rdev() (referring to both the boot medium where the program is
stored before loading, and the memory area where it is loaded after) and
makes sure that programs are always located and loaded in a single
operation. This makes CBFS verification easier to implement and secure
because it avoids leaking a raw rdev of unverified data outside the CBFS
core code.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I7a5525f66e1d5f3a632e8f6f0ed9e116e3cebfcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
From ALSA reviewer suggest to change the name to RTL1015.
Details in below threads:
https://www.spinics.net/lists/alsa-devel/msg123395.html
BUG=b:177971830
TEST=: ALC1015P driver can probe properly.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I2762852bdc3164346e3618c373aa4d3336415653
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Missing acpi_dp_write and correct the name from sdb to sdb-gpios for
driver.
BUG=b:177971830
TEST: ALC1015P driver can get sdb-gpio properly.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I2728a7dad695d5c97e85c5d86b1effea1595da65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51379
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
EFI_PEI_MP_SERVICES_STARTUP_ALL_APS passes in a boolean flag singlethread
which indicates whether the work should be scheduled in a serially on all APs
or in parallel. Current implementation of this function mp_startup_all_aps
always schedules work in parallel on all APs. This implementation ensures
mp_startup_all_aps honors to run serialized request.
BUG=b:169114674
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I4d85dd2ce9115f0186790c62c8dcc75f12412e92
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51085
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The current driver is using chip registers map to configure the SAR
sensor, which is opaque, especially when the datasheet is not published
widely.
Use more descriptive names, as defined in Linux kernel documentation at
https://www.kernel.org/doc/Documentation/devicetree/bindings/iio/proximity/semtech%2Csx9310.yaml
BUG=b:173341604
BRANCH=volteer
TEST=Dump all tables, check semtech property:
for i in $(find /sys/firmware/acpi/tables/ -type f) ; do
f=$(basename $i); cat $i > /tmp/$f.dat ; iasl -d /tmp/$f.dat
done
In SSDT.dsl, we have:
Package (0x06)
{
Package (0x02)
{
"semtech,cs0-ground",
Zero
},
Package (0x02)
{
"semtech,startup-sensor",
Zero
},
Package (0x02)
{
"semtech,proxraw-strength",
Zero
},
Package (0x02)
{
"semtech,avg-pos-strength",
0x0200
},
Package (0x02)
{
"semtech,combined-sensors",
Package (0x03)
{
Zero,
One,
0x02
}
},
Package (0x02)
{
"semtech,resolution",
"finest"
}
}
Change-Id: I8d1c81b56eaeef1dbb0f73c1d74c3a20e8b2fd7b
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch pulls control of the memory pool serving allocations from the
CBFS_CACHE memlayout area into cbfs.c and makes it a core part of the
CBFS API. Previously, platforms would independently instantiate this as
part of boot_device_ro() (mostly through cbfs_spi.c). The new cbfs_cache
pool is exported as a global so these platforms can still use it to
directly back rdev_mmap() on their boot device, but the cbfs_cache can
now also use it to directly make allocations itself. This is used to
allow transparent decompression support in cbfs_map().
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I0d52b6a8f582a81a19fd0fd663bb89eab55a49d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Use lowercase `port` in both the spec and the body.
Change-Id: I3d1e2abe03eedcaf57716af444a3e3b8a61b60d4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
