The QEMU XHCI driver does not implement the Port Change Detect bit
in the USBSTS register. As a result no devices are attached without
looking at each port individually.
Detect this as a quirk based on the QEMU XHCI controller PCI ID,
and apply it to the root hub quirk list so it can get used by the
generic hub driver to skip this check.
With this change an attached USB mass storage device is detected and
able to boot when supplied to qemu:
-drive if=none,id=usbmsc,format=raw,file=/tmp/disk.img
-device qemu-xhci,id-xhci
-device usb-storage,bus=xhci.0,drive=usbmsc
Change-Id: I6689cb1dbb24c93d45f5c5ef040b713925d07588
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39839
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
USB 3.1 GEN2 report speed type 4, add into speed enum.
BUG=b:139787920
BRANCH=N/A
TEST=Build libpayload and depthcharge on sarien and boot with
USB GEN2 HUB with USB disk. Check ultra speed device in cbmem log.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia0ef12b2f0d91bf0d0db766bbc9019de1614a4f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35023
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We're planning to have a use case with a custom USB device that
implements the USB mass storage protocol on its bulk endpoints, but does
not have the normal MSC class/protocol interface descriptors and does
not support class-specific control requests (Get Max LUN and Bulk-Only
Reset). We'd like to identify/enumerate the device via
usb_generic_create() in our payload but then reuse all the normal MSC
driver code. In order to make that possible, this patch factors a new
usb_msc_force_init() function out of usb_msc_init() which will
initialize an MSC device without checking its descriptors. It also adds
some "quirks" flags that allow devices registered this way to customize
behavior of the MSC stack.
Change-Id: I50392128409cb2a879954f234149a5e3b060a229
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Increase the timeout for USB requests to 5 seconds for all USB host
controllers.
Prior to this fix, the xCHI driver was detecting false timeouts during
SET ADDRESS requests when nested downstream hubs were connected to the
xHCI root hub.
BUG=b:124730179
BRANCH=sarien
TEST=Build libpayload and depthcharge on sarien/arcada.
TEST=Without change replicate USB set address timeouts in depthcharge
when dock and 4K monitor connected (which includes a total of 4 USB
hubs). With timeout fix, depthcharge boots OS with no USB errors and
the same USB topology. Note that this tests xHCI operation only.
Change-Id: I53e3e67d893420e7c9e8b52c47dd0edb979e5468
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
xhci_rh_port_speed return -1 if the port is disabled. The usb_speed enum
is unsigned so this results in a positive value which implies success.
Adding a -1 to the enum will make it signed so the >= 0 check will work
correctly.
BUG=b:76831439
TEST=verified on grunt that -1 is returned when port is disabled.
Change-Id: I98a373717d52dfb6ca4dcc53a00dc1b4c240a919
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
BUG=chrome-os-partner:49249
TEST=Compiles and boots and detect USB storage
BRANCH=none
Change-Id: I9007399e1f785e6f1d2258225e3f7cc602053aed
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1db43f53973d2124e41186777caa829aa346ace3
Original-Change-Id: I943d19a3a7d785bd075073b57ba6388662d7df90
Original-Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/333311
Original-Commit-Ready: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/14659
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some FSF addresses found their way back into our tree.
Change-Id: I34b465fc78734d818eca1d6962a1e62bf9d6e7f3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/11145
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
With split transaction, dwc2 host controller can handle full- and
low-speed devices on hub in high-speed mode. This commit adds support
for split control and interrupt transfers
BUG=None
TEST=Connect usb keyboard through hub, usb keyboard can work
BRANCH=None
Change-Id: If7a00db21c8ad4c635f39581382b877603075d1a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4fb514b7f7f7e414fa94bfce05420957b1c57019
Original-Change-Id: I07e64064c6182d33905ae4efb13712645de7cf93
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/283282
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/10956
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
dwc2 host core do not have a periodic schedule list, so try to send
an interrupt packet in poll_intr_queue() function and use frame
number read from usb core register to calculate time and schedule
transfers.
BUG=None
TEST=Tested on RK3288 with two USB keyboards(connect to SoC without
USB hub), both work correctly.
BRANCH=None
Change-Id: I16f7977c45a84b37c32b7c495ca78ad76be9f0ce
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3d0206b86634bcfdbe03da3e2c8adf186470e157
Original-Change-Id: Ie54699162ef799f4d3d2a0abf850dbeb62417777
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/280750
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: http://review.coreboot.org/10774
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Found in rockchips rk3288 as used in google/veyron.
BUG=None
TEST=None
BRANCH=None
Change-Id: I2f2c36c5bea3986a8a37f84c75608b838a8782ae
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 59a0bcd97e8d0f5ce5ac1301910e11b01e2d24b1
Original-Change-Id: Ic89ed54c48d6f9ce125a93caf96471abc6e8cd9d
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/272108
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: http://review.coreboot.org/10689
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
BUG=chrome-os-partner:29778
TEST=emerge-veyron libpayload
Change-Id: I33f312a939e600b8f4e50a092bb61c5d6bc6d741
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 39ffe53336a2a3b2baa067cdd3dccca5ae93f68e
Original-Change-Id: Idad1ad165fd44df635a0cb13bfec6fada1378bc8
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/211053
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9453
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Fix pointer related casts since this can create a problem for 64-bit systems.
BUG=None
BRANCH=None
TEST=Compiled successfully for link, nyan using emerge-* libpayload
Original-Change-Id: I4cbd2d9f1efaaac87c3eba69204337fd6893ed66
Original-Reviewed-on: https://chromium-review.googlesource.com/199564
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Original-Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Original-Tested-by: Furquan Shaikh <furquan@chromium.org>
(cherry picked from commit 914b118a64b0691aeca463dff24252db9c24109e)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I11f070ed5d3eddd8b9be30c428cb24c8439e617b
Reviewed-on: http://review.coreboot.org/7905
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
I always thought the support for multiple logical SCSI units in the USB
mass storage class was a dead feature. Turns out that it's actually used
by SD card readers that provide multiple slots (e.g. one regular sized
and one micro-SD). Implementing perfect support for that would require a
major redesign of the whole MSC stack, since the one device -> one disk
assumption is deeply embedded in our data structures.
Instead, this patch implements a poor man's LUN support that will just
cycle through all available LUNs (in multiple calls to usb_msc_poll())
until it finds a connected device. This should be reasonable enough to
allow these card readers to be usable while only requiring superficial
changes.
Also removes the unused 'protocol' attribute of usb_msc_inst_t.
BRANCH=rambi?,nyan
BUG=chrome-os-partner:28437
TEST=Alternatively plug an SD or micro-SD card (or both) into my card
reader, confirm that one of them is correctly detected at all times.
Original-Change-Id: I3df4ca88afe2dcf7928b823aa2a73c2b0f599cf2
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/198101
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit 960534a20e4334772c29355bb0d310b3f41b31ee)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I39909fc96e32c9a5d76651d91c2b5c16c89ace9e
Reviewed-on: http://review.coreboot.org/7904
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
We recently changed the USB stack to detach devices aggressively that we
don't intend to use. This alone is not really a problem, but it
exarcerbates the fact that our device detachment itself is not very
good. We destroy any local info about the device, but we don't properly
disable the offending port. The device keeps thinking that it's active,
and if we later try to reuse that device address for another device
things become confused.
The real fix would be to properly disable all ports that we don't intend
to use. Unfortunately, this isn't really possible in our current
device/hub polymorphism structure, and I don't want to hack a new
disable_port() callback into usbdev_t that really doesn't belong there.
We will only be able to fix this cleanly after we ported all root hubs
to the generic_hub interface.
Until then, an easy workaround is to just avoid reusing addresses as
long as possible. This is firmware, so the chance that we'll ever run
through 127 devices is really small in practice. Even if we ever fix the
underlying issue, it's probably a smart precaution to keep.
BRANCH=nyan,rambi
BUG=chrome-os-partner:28328
TEST=Boot from a hub that has an "unknown" device in an earlier port
than the stick you want to boot from, make sure you can still boot.
Original-Change-Id: I9b522dd8cbcd441e8c3b8781fcecd2effa0f23ee
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/197420
Original-Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit 28b48aa69b55a983226edf2ea616f33cd4b959e2)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Id4c5c92e75d6b5a7e8f0ee3e396c69c4efd13176
Reviewed-on: http://review.coreboot.org/7881
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch represents a major overhaul of the USB enumeration code in
order to make it cleaner and much more robust to weird or malicious
devices. The main improvement is that it correctly parses the USB
descriptors even if there are unknown descriptors interspersed within,
which is perfectly legal and in particular present on all SuperSpeed
devices (due to the SuperSpeed Endpoint Companion Descriptor).
In addition, it gets rid of the really whacky and special cased
get_descriptor() function, which would read every descriptor twice
whether it made sense or not. The new code makes the callers allocate
descriptor memory and only read stuff twice when it's really necessary
(i.e. the device and configuration descriptors).
Finally, it also moves some more responsibilities into the
controller-specific set_address() function in order to make sure things
are initialized at the same stage for all controllers. In the new model
it initializes the device entry (which zeroes the endpoint array), sets
up endpoint 0 (including MPS), sets the device address and finally
returns the whole usbdev_t structure with that address correctly set.
Note that this should make SuperSpeed devices work, but SuperSpeed hubs
are a wholly different story and would require a custom hub driver
(since the hub descriptor and port status formats are different for USB
3.0 ports, and the whole issue about the same hub showing up as two
different devices on two different ports might present additional
challenges). The stack currently just issues a warning and refuses to
initialize this part of the hub, which means that 3.0 devices connected
through a 3.0 hub may not work correctly.
Change-Id: Ie0b82dca23b7a750658ccc1a85f9daae5fbc20e1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170666
Reviewed-by: Kees Cook <keescook@chromium.org>
(cherry picked from commit ecec80e062f7efe32a9a17479dcf8cb678a4a98b)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6780
Tested-by: build bot (Jenkins)
This patch removes the confusing concept of a special "xhci_speed" with
a different numeric value from the usual speed used throughout the USB
core (except for the places directly interacting with the xHC, which are
explicitly marked). It also moves the MPS0 decoding function into the
core and moves some definitions around in preparation of later changes
that will make the stack SuperSpeed-ready. It makes both set_address
implementations share a constant for the specification-defined
SetAddress() recovery delay and removes pointless additional delays from
the non-XHCI version.
Change-Id: I422379d05d4a502b12dae183504e5231add5466a
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170664
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Ronald Minnich <rminnich@chromium.org>
(cherry picked from commit f160d4439c0d7cea1d2e6b97207935d61dcbb2f2)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6776
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The existing USB_MEMORY mechanism to instantiate non-PCI host
controllers is clunky and inflexible... most importantly, it doesn't
allow multiple host controllers of the same kind. This patch replaces it
with a function that allows payloads to directly instantiate as many
host controllers of whatever type they need.
Change-Id: Ic21d2016a4ef92c67fa420bdc0f0d8a6508b69e5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169454
Reviewed-by: Stefan Reinauer <reinauer@google.com>
(cherry picked from commit b6e95c39dd91f654f0a345f17b3196f56adf4891)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6644
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
being a good citizen on the box, libpayload tries to return to EHCI
mode on shutdown, so a non-XHCI capable USB driver after it (eg. in
the OS) finds something to work with.
Change-Id: Id227d646e08a258b841c644263112f0815dd486c
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/4547
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Mass storage devices such as card readers show up as
as USB devices. However the media not be inserted. In those
situations the previous code would just fake a disk and
call usbcreate_disk. This is inappropriate because it forms
a 1:1 mapping of USB device to disk leading to the inability
to remove the disk and/or handle "hot plug" card insertion
and removals.
To alleviate this issue introduce the notion of ready to the
usbmsc structure. It tracks detached, not ready, and ready
states. The polling routine is then used to track not ready
to ready transitions thereby creating and removing disks
appropriately. This handles the case of inserting and removing
a card that shows up as a new disk.
Booted recovery mode. Able to observe inerstion and removal
of sdcard. Also able to insert valid USB flash drive to boot
as well.
Change-Id: I3eefbe537ec1b9c975744b8984b06c17ae236f40
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57948
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4226
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Restructure USB stack to not depend on PCI, and
make PCI stub available on x86, but provide fixed
BARs for ARM (Exynos 5)
Change-Id: Iee7c8b134c22b661a9a515e24943470c9dbadd1f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49970
Reviewed-on: http://review.coreboot.org/4175
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Read bInterval from endpoint descriptors and store it in our endpoint_t
struct. The interval is encoded dependently on the device' speed and the
endpoint's type. Therefore, it will be normalized to the binary logarithm
of the number of microframes, i.e.
t = 125us * 2^interval
The interval attribute will be used in the xHCI driver.
Change-Id: I65a8eda6145faf34666800789f0292e640a8141b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3449
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
xHCI requires special treatment of set_address since it determines
the device number itself (instead of the driver, as with the other
controllers). The controller also wants to validate a chosen device
configuration and we need to setup additional structures for the
device and the endpoints.
Therefore, we add three functions to the hci_t structure, namely:
set_address()
finish_device_config()
destroy_device()
Current implementation for the Set Address request moved into
generic_set_address() which is set_address() for the UHCI, OCHI and
EHCI drivers. The latter two are only provided as hooks for the xHCI
driver.
The Set Configuration request is moved after endpoint enumeration.
For all other controller drivers nothing changes, as there is no other
device communication between the lines where the set_configuration()
call moved.
Change-Id: I6127627b9367ef573aa1a1525782bc1304ea350d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3447
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These values are already used in this usb stack.
Change-Id: If96f1dc2b67fbc13dfc4ae2d84e8f9945aa03163
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3448
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It might be useful to provide a USB driver in the payload itself instead of in
libpayload. For example there are multiple payloads being built and linked
against the same libpayload, and they might not need or even want to have the
same set of drivers installed.
This change adds two new functions, usb_generic_create and usb_generic_remove,
which behave like the usbdisk_create and usbdisk_remove functions which are
defined for USB mass storage devices. If a USB device isn't recognized and
claimed by one of the built in USB class drivers (currently hub, hid, and msc)
and the create function is defined, then it will be called to give the payload
a chance to use the device. Once it's removed, if usb_generic_remove is
defined it will be called, effectively giving the payload notice.
Built and booted depthcharge on Link. Built depthcharge for Daisy. Built
a netbooting payload, called usb_poll() with those functions implemented, and
verified that they were called and that the devices they were told about were
reasonable and the same as what was reported by lsusb in the booted system.
Change-Id: Ief7c0a513b60849fbf2986ef4ae5c9e7825fef16
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2666
Tested-by: build bot (Jenkins)
Reviewed-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is so the user of libpayload can attach data to the device which it can
retrieve when the device is referred to later, for instance in usbdisk_remove.
Otherwise, there's no direct connection from the usbdev_t structure to any
bookkeeping in the host firmware.
Change-Id: I36fe693b0dcd2098e359c26744e376e73bd3a723
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2513
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
usb_controller_initialize() is not declared in any header file nor
called from outside of usbinit.c, so make it static.
set_configuration() looks like beeing non-static on purpose (like the
other helpers around it in usb.c), so put a prototype into usb.h.
Change-Id: I08d93b3769d8398bb43462d9afdfeec81fef93ec
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1894
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
uhci_reset() differs in semantics compared to the other HCI's reset()
implementations. uhci_reset() does some initialization work after a
controller reset. So move the initialization part to a new function,
uhci_reinit(), which get's exported through a new entry in hci_t:
hci_t.init().
Warning: This breaks code that relies on the current, special,
counterintuitive behaviour of uhci_reset(). If one wants a working host
controller after calling hci_t.reset(), he should call hci_t.init()
afterwards.
Change-Id: Ia7ce80865d12d11157645ce251f77f349f8e3c34
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1851
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The semantics of the controller functions, start(), stop(), reset() and
shutdown(), are not self-explanatory which let to some confusion. At
least the reset() functions of the different host controller drivers
were implemented following different interpretations. Let's make the
intended behaviour of these functions clear.
The stated inconsistencies will be addressed in following commits.
Change-Id: Id2e300f65c21039218b6ba3f87c0fcd4f0dda0a8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1848
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The "debug" macro used internally in the libpayload USB subsystem was very
generically named and would leak into consumers of the library that included
usb.h directly or indirectly. This change turns that #define from a macro into
a static inline function to move away from the preprocessor, and also renames
it to usb_debug so it's less likely to collide with something unrelated.
Change-Id: I18717df111aa9671495f8a2a5bdb2c6311fa7acf
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1738
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Add controller type (UHCI, OHCI, EHCI or XHCI)
into usbdev_hc (hci_t) struct, so now we know
which type selected controller have. It needed
to access controller specific data, if access
usb tree outside of libpayload (e.g. in payload
intself)
Change-Id: I7df947bbb56a50d0d792ccd4d3a6b021ee95e2ea
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/1145
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This lets the init of usb mass storage return if the device
configuration is unusable. Also add some checks for proper shutdown so
we don't free/remove an uninitialized device.
Change-Id: I6daf9b38e632b6e381bcd5a7717f0f1a3150b64a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1130
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This enables logical detachment of unresponsive usb devices (i.e.
devices not responding to control transfers) in the usb mass storage
driver. Without the detection of unresponsive devices we wait way too
long for the device to become ready.
Change-Id: I8b8cf327f49dde25afaca4d3066f16ea86b99d3d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1121
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
With split transactions, the EHCI host controller can handle full- and
low-speed devices on hubs in high-speed mode. This adds support for split
transactions for control and bulk transfers.
Change-Id: I30fa1ce25757f33b1e6ed34207949c9255f05d49
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1081
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This function will be used by the USB hub driver.
Change-Id: I4d1d2e94f4442cbb636ae989e8ffd543181c4357
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1079
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
We have fatal(), which is just as good.
Coccinelle script:
@@
expression E;
@@
-usb_fatal(E)
+fatal(E)
Change-Id: Iabecbcc7d068cc0f82687bf51d89c2626642cd86
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/395
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
The USB stack is pretty noisy. Reduce the output to a sane level.
Change-Id: I250949e5cf74a8c6d43822b2e7487143b2ae1c65
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Reviewed-on: http://review.coreboot.org/393
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Move controller specific data structures into private headers,
to avoid conflicts between controller drivers.
Factor out the USB PID ids, which are only exposed on UHCI. It's
of not much use on the other controllers.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5616 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- support MMC2 devices
- make usb stack more solid
- drop some unused functions
- fix lowspeed/speed naming
- add support for "quirks"
- improve usbhid driver
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5299 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
560bytes/controller)
- no need for the client of libpayload to implement
usbdisk_{create,remove}, just because USB was compiled in.
- usb hub support compiles, and works for some trivial cases (no device
detach, trivial power management)
- usb keyboard support works in qemu, though there are reports that it
doesn't work on real hardware yet.
- usb keyboard is integrated in both libc-getchar() and curses, if
CONFIG_USB_HID is enabled
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3662 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Duncan Laurie