When the first CSW transfer failed, get_csw function will retry
CSW transfer again, but the return value is not updated.
Change-Id: I289916baa08d0a189d659164a0002347f6f435db
Signed-off-by: Changqi Hu <changqi.hu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
In interactive payloads, the USB stack's poll procedure is implicitly
called from the UI loop. Since all USB control transfers are handled
synchronously, polling hubs with these slows the UI significantly down.
So switch to interrupt transfers that are done asynchronously and only
perform control transfers when the hub reported a status change.
We use the interrupt endpoint's max packet size instead of the theo-
retical transfer length of `(bNrPorts + 1) / 8` as Linux' code mentions
hubs that return too much data.
Change-Id: I5af02d63e4b8e1451b160b77f3611b93658a7a48
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/18499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
USB 3.1 GEN2 report speed type 4, add into speed enum.
BUG=b:139787920
BRANCH=N/A
TEST=Build libpayload and depthcharge on sarien and boot with
USB GEN2 HUB with USB disk. Check ultra speed device in cbmem log.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia0ef12b2f0d91bf0d0db766bbc9019de1614a4f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35023
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We're planning to have a use case with a custom USB device that
implements the USB mass storage protocol on its bulk endpoints, but does
not have the normal MSC class/protocol interface descriptors and does
not support class-specific control requests (Get Max LUN and Bulk-Only
Reset). We'd like to identify/enumerate the device via
usb_generic_create() in our payload but then reuse all the normal MSC
driver code. In order to make that possible, this patch factors a new
usb_msc_force_init() function out of usb_msc_init() which will
initialize an MSC device without checking its descriptors. It also adds
some "quirks" flags that allow devices registered this way to customize
behavior of the MSC stack.
Change-Id: I50392128409cb2a879954f234149a5e3b060a229
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Some broken USB mass storage devices send another zero-length packet at
the end of the data part of a transfer if the amount of data was evenly
divisible by the packet size (which is pretty much always the case for
block reads). This packet will get interpreted as the CSW and screw up
the MSC state machine.
This patch works around this issue by retrying the CSW transfer when it
was received as exactly 0 bytes. This is the same mitigation the Linux
kernel uses and harmless for correctly behaving devices. Also tighten
validation of the CSW a little, making sure we verify the length before
we read any fields and checking the signature in addition to the tag.
Change-Id: I24f183f27b2c4f0142ba6c4b35b490c5798d0d21
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34485
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A typo introduced in commit bf2c693f89
made the driver not build: DWC_SLEEP_TIME_US instead of
DWC2_SLEEP_TIME_US.
Change-Id: I197b25fd4f568cce7a4bbcee8cc285b25b26afb1
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Keith Short <keithshort@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Increase the timeout for USB requests to 5 seconds for all USB host
controllers.
Prior to this fix, the xCHI driver was detecting false timeouts during
SET ADDRESS requests when nested downstream hubs were connected to the
xHCI root hub.
BUG=b:124730179
BRANCH=sarien
TEST=Build libpayload and depthcharge on sarien/arcada.
TEST=Without change replicate USB set address timeouts in depthcharge
when dock and 4K monitor connected (which includes a total of 4 USB
hubs). With timeout fix, depthcharge boots OS with no USB errors and
the same USB topology. Note that this tests xHCI operation only.
Change-Id: I53e3e67d893420e7c9e8b52c47dd0edb979e5468
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This patch is a raw application of
find payloads/ -type f | \
xargs sed -i -e 's/IS_ENABLED\s*(CONFIG_/CONFIG(/g'
Change-Id: I883b03b189f59b5d998a09a2596b0391a2d5cf33
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Fill reg_base with physical register base address.
Tested on Lenovo T500.
Change-Id: If42135c8e10b70d5ac9626521abd9cca3cf40053
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18600
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For debugging purposes always set the pciaddr attribute.
Tested on Lenovo T500.
Change-Id: I83a0e7f7196ed251fa0becc4e56bef3ca68f20f4
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18599
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=none
TEST=compiled on grunt and made sure USB still works in depthcharge
Change-Id: I972f4604bb5ff3838cb15f323c5a579ad890ecf5
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
If a port disconnects after a reset we should abort any initialization
on the port. This might mean the device has re-enumerated as a 3.0 device
so the hub should be scanned again.
BUG=b:76831439
TEST=Verified USB-C devices that get detected correctly in depthcharge.
Change-Id: Iad899544684312df1bef08d69b5c7f41eac3a21c
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Make it obvious that the command has failed.
BUG=b:76831439
TEST=Verified on grunt
Change-Id: Ifa0b2fb087f5f0a36ba017a774fc98b33ab035a4
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
xhci_rh_port_speed return -1 if the port is disabled. The usb_speed enum
is unsigned so this results in a positive value which implies success.
Adding a -1 to the enum will make it signed so the >= 0 check will work
correctly.
BUG=b:76831439
TEST=verified on grunt that -1 is returned when port is disabled.
Change-Id: I98a373717d52dfb6ca4dcc53a00dc1b4c240a919
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This makes it easier to know what offset each register references.
BUG=b:76831439
TEST=none
Change-Id: I92dcbd463ceb4dd8edbbd97b51a4e9aa32a983a6
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add a new method to retrieve active usb keyboard modifiers.
Change-Id: Ief6679ce782b58b9ced207f4f27504fb2a517b76
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18602
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The USBHID driver zero-initializes some but not all of the fields in its
usbhid_inst_t structure. This is a problem because under some
circumstances, some of the uninitialized fields may be read and lead to
incorrect behavior. Some (broken) USB keyboards keep sending reports
that contain all zeroes even when they have no new keys... these usually
get silently ignored, but if the usbhid_inst_t structure is in an
inconsistent state where 'previous' is zeroed out but 'lastkeypress'
is non-zero because it wasn't properly initialized, these reports will
be interpreted as keyrepeats of the bogus 'lastkeypress'. This patch
changes the code to just xzalloc() the whole structure so we won't have
to worry about initialization issues anymore.
Change-Id: Ic987de2daaceaad2ae401a1e12b1bee397f802ee
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/23766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
We have found a non-compliant USB hub (RealTek RTS 5413) that does not
set a port's Connect Status Change bit on its USB 3.0 half if the port
had already been connected while the hub was being reset. To work around
this bug, this patch adds code to initially request the status of every
port after a hub was enumerated, clear the Connect Status Change bit if
set, and then enumerate the port iff it is currently connected,
regardless of whether the change bit was set. A similar behavior can
also be found in the Linux kernel.
BRANCH=oak
BUG=b:35929438
TEST=Booted Elm with this change, my USB 3.0 sticks enumerate now even
if they had been plugged in since boot.
Change-Id: I8a28252eb94f005f04866d06e4fc61ea265cee89
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18729
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Currently we just disabled ohci interrupts when calling ohci_shutdown,
Which would not actually shutdown the ohci controller, for example it
may still written the increased HccaFrameNumber to Hcca buffer.
Perform a soft reset to ohci controller as the linux kernel ohci-hcd
driver does.
BUG=chrome-os-partner:60996
BRANCH=None
TEST=Checked on gru, no more "BUG: Bad page state" error in kernel.
Change-Id: I128ab6ba455ac5383a4d48be0bc12b8bb4533464
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4749fc82fdd1b74ca3f2ed3fdf0ef53a5e161087
Original-Change-Id: I3f192aea627ba2fa69533bc0a4270466ca18f2a7
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/426338
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/18125
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Chrome OS builds always have some inherent differences to "standard"
libpayload configurations: they don't want to use curses or things like
storage drivers, they always use the coreboot framebuffer and USB, etc.
This patch reintroduces CONFIG_LP_CHROMEOS as an option that only
affects Kconfig defaults. This allows Chrome OS builds to select most of
what they need in one go and reduces board-specific .config files to
only the options that are really specific to that board.
Also restricts the 8250_SERIAL_CONSOLE Kconfig to only default to yes on
x86 boards, which probably makes sense for all of libpayload (some but
far from all ARM boards use 8250-compatible UARTs, and we should
probably not default a platform option unless it's going to be correct
with very high probability).
BRANCH=None
BUG=None
TEST=Built and booted Jerry and Oak.
Change-Id: Ie0c0593ffd399608d2cbfb83d20891f6f1864914
Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Id: e558f59
Original-Change-Id: I609637cd2ea7dfb4558aa3c04c90b64038c9ab57
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/347970
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17024
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
All but ga-g41m-es2l/cmos.default had multiple final newlines.
ga-g41m-es2l/cmos.default had no final newline.
Change-Id: Id350b513d5833bb14a2564eb789ab23b6278dcb5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16361
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Antonello Dettori <dev@dettori.io>
Move the configuration of the timer, storage and USB drivers from the
main Kconfig to three separate ones stored in the respective
directories.
This reduces the LOC of Kconfig and makes it more manageable.
Change-Id: I0786dbc1d5d8317c8ccb600f5de9ef4a8243d035
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/15914
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
1. Make the xHCI driver to support xHCI controller v1.1
2. And a new function xhci_ring_doorbell(), it aims to
add a memory barrier before ringing the doorbell, to ensure
all TRB changes are written to memory.
BRANCH=none
BUG=chrome-os-partner:52684
TEST=boot from USB on Kevin rk3399 platform
Change-Id: Ife1070d1265476d0f5b88e2acf3299fc84af5832
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 0c21e92
Original-Change-Id: I4e38e04dc3c7d32ee4bb424a473c70956a3c3ea9
Original-Signed-off-by: Liangfeng Wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/346831
Original-Commit-Ready: Brian Norris <briannorris@chromium.org>
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15111
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
BUG=chrome-os-partner:49249
TEST=Compiles and boots and detect USB storage
BRANCH=none
Change-Id: I9007399e1f785e6f1d2258225e3f7cc602053aed
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1db43f53973d2124e41186777caa829aa346ace3
Original-Change-Id: I943d19a3a7d785bd075073b57ba6388662d7df90
Original-Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/333311
Original-Commit-Ready: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/14659
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Existing Intel xHCI controllers require a delay of 1 ms,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.
Verified CherryView / Braswell platforms go through over
1000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang in depthcharge.
BRANCH=None
BUG=None
TEST=Verified CherryView / Braswell platforms go through
over 1000 warm reboot cycles, without any xHCI reset hang
in depthcharge.
Change-Id: I8eff5115ca52738bdcf8bc65fbfb2a5f60a0abe1
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3e7ea70df36e3bf35a6ee1297640900ee76bfdac
Original-Change-Id: Id681a19d0eedb0e2c29e259c5467bcde577e3460
Original-Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/310022
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/12325
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We found that some SanDisk Cruizer Glide CZ60 sticks (confirmed on 16GB
and 64GB versions) have a problem responding to our first GET_MAX_LUNS
request right after they received their SET_CONFIGURATION. They will
continually return a NAK until the host gives up (which is 2
user-noticable seconds for us). Adding a small delay of about 15us seems
to be enough to fix the issue, but let's do 50 to be save.
Confirmed with both MT8173 and Intel LynxPoint XHCI controllers.
BRANCH=None
BUG=chrome-os-partner:45473
TEST=No notable delay before detecting stick on Oak and Falco.
Change-Id: Ib03944d6484de0ccecbb9922d22666f54c9d53dd
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 589f19a901275fb8b00de4595763a7d577bed524
Original-Change-Id: I95c79fe40d3ad79f37ce2eb586836e5de55be454
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/308980
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/12229
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Certain Lexar USB disks may fail during the first calls to
get_descriptor(..., DT_CFG, ...) for unknown reasons. Therefore, make
several attempts before giving up.
BUG=chromium:466758
TEST=Manual on Samus. Go to recovery mode, verify that Lexar LJDS70 USB
stick is bootable.
BRANCH=None
Change-Id: I476ac22f9c4f844c60ebc6e53af8c144d70bb9d4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 93a0570b343479dd22506ad4d7961f0ea4251f8c
Original-Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Original-Change-Id: Ie581c7c71c53816065c7f59202581888a79e445e
Original-Reviewed-on: https://chromium-review.googlesource.com/302403
Original-Commit-Ready: Shawn N <shawnn@chromium.org>
Original-Tested-by: Shawn N <shawnn@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/12133
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
If the device has already been disconnected then we shouldn't enable
host channel to start any transfer, otherwise this channel goes into
an odd state the channel is enabled but can not be disabled by set
hcchar.chdis=1. So we need check the device connect status before
enable channel.
BRANCH=None
BUG=chrome-os-partner:44534
TEST=None
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ae3e690b2cd4a9ea8b5766ac873b0e00bf3a23de
Original-Change-Id: Ib3ecf486649ca11b302144f9c00a5e88424e90fa
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/298402
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-(cherry picked from commit ea96f947b5304fdde2e0991d23febaeba209dde1)
Original-Reviewed-on: https://chromium-review.googlesource.com/299398
Original-Commit-Ready: David Hendricks <dhendrix@chromium.org>
Original-Tested-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Change-Id: Idf48ffbc4c2794900e09dec6b2e34e33b21f87b4
Reviewed-on: http://review.coreboot.org/11662
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
When disconnect is detected in dwc2_split_transfer() the split
configuration registers should be cleared before return.
BRANCH=None
BUG=chrome-os-partner:44534
TEST=On Jerry, usb hot plug works with devices behind hubs
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 37594d8b4490b6d393d19d17d8e497db7de8817d
Original-Change-Id: Ie1eecec067305874513c6ceb95df4240dc393cd6
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/295625
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-(cherry picked from commit d543e14cdc73bd549dd553c8d1d07672a1307981)
Original-Reviewed-on: https://chromium-review.googlesource.com/299700
Original-Commit-Ready: David Hendricks <dhendrix@chromium.org>
Original-Tested-by: David Hendricks <dhendrix@chromium.org>
Change-Id: Ib4604097743f2f9d763b29ee27f3bc1788a85a62
Reviewed-on: http://review.coreboot.org/11661
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Seems like our transferred bytes calculation for OUT transfers that span
more than one packet had been wrong, and we just got lucky that we never
noticed it before. The HCTSIZ.xfersize register field we're reading only
counts bytes transferred by the last packet we sent.
OUT endpoints cannot have short transfers -- every transfer should
either finish all bytes we wanted to send or end in a proper error
condition. Therefore, in the absence of an error we can just conclude
that all input bytes have been transferred.
BRANCH=veyron
BUG=chrome-os-partner:35525
TEST=SMSC95xx netboot on Jerry now works.
Change-Id: I57349e697c428df6b56e2f6f62e87652ef1e7a94
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Original-Commit-Id: 0abee13b6d89dec12c6fff581ece1836393c7703
Original-Change-Id: Id0a127e6919f5786ba05218277705dda1067b8c3
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/293956
Original-Reviewed-by: yunzhi li <lyz@rock-chips.com>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/11404
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Check device connect status while waiting for usb transfer complete
Avoid coreboot get stuck when usb device unplugged
BUG=chrome-os-partner:35525
TEST=None
BRANCH=None
Original-Change-Id: Id103501aa0d8b31b0b81bef773679c0fad79f689
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/292630
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/292966
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Tested-by: David Hendricks <dhendrix@chromium.org>
Original-Commit-Queue: David Hendricks <dhendrix@chromium.org>
Change-Id: I49396b74131dbfda505d9d3de5adbdc87eb92ce1
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Reviewed-on: http://review.coreboot.org/11236
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The xhci_rh_port_status_changed() function tries to always clear all
port status bits, even though most of them don't interest us. This is
generally a smart thing to do since not clearing a status bit may cause
the controller to not generate any more Port Status Change Events.
However, the bitmask we currently use doesn't cover bit 23 (Port Config
Error Change) and instead covers bit 16 (Port Link State Write Strobe)
which is not really related to this and not a W1C bit. Probably a typo,
so let's fix that.
BRANCH=None
BUG=None
TEST=Plugged/unplugged a bunch of USB devices on an XHCI Falco.
Original-Change-Id: Ia83f5b72cce094859c0f0e730752d7b5cfa6e1c6
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/291842
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I11f5fe38cb70055daf6e866a8ee84ca80488e3bf
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/11194
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The 1.1 revision of the XHCI specification added an extra 5 bits to the
Max Scratchpad Bufs field of HCSPARAMS2 that newer controllers make use
of. Not honoring these bits means we're not allocating as many
scratchpad buffers as the controller expects, which means it will
interpret some uninitialized values from the end of the pointer array as
scratchpad buffer pointers, which obviously doesn't end well. Let's fix
that.
BRANCH=none
BUG=chrome-os-partner:42279
TEST=Makes a USB-related memory corruption issue disappear.
Original-Change-Id: I7c907492339262bda31cdd2b5c0b588de7df8544
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/291681
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Iba1007bfebffe1f564f78bb875fff9ba0fe11a38
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/11189
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
If short packet detected, stop this transfer and return the actual
transferred size
BUG=chrome-os-partner:42817
TEST=Netboot could run well
BRANCH=None
Original-Change-Id: Icb4317f48aa04ac15bb1886b81d2e3c472d123d0
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/288215
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-(cherry picked from commit d372343b4e3d664ce2d76dbf55a5061b5d496bba)
Original-Reviewed-on: https://chromium-review.googlesource.com/291064
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Change-Id: I43d9edffe2074c037f2df203621863e54d2597fa
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Reviewed-on: http://review.coreboot.org/11187
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch re-adds a few fixes that originally went into the
chromeos-2013.04 tree. I kinda seem to have slipped them into the
backport of Nico's original XHCI patch (crosreview.com/168097) instead
of making a new change, which was not very clever and caused them to be
forgotten in the later upstreaming wave.
Changing internal XHCI error numbers is just a cosmetic change to make
them uniquely identifyable in debug output. Bumping the timeout to 3
seconds is an actually important fix since we have seen mass storage
devices needing that much in the past.
BRANCH=None
BUG=None
TEST=Diffed payloads/libpayload/drivers/usb between chromeos-2013.04 and
chromeos-2015.07, confirmed that no serious differences remain.
Original-Change-Id: I03d865dbe536072d23374a49a0136e9f28568f8e
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/290423
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I5d773d3a23683fb2164916cc046f4a711b8d259e
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/11178
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Before the controller's destroy_device() could interrogate
the usbdev_t object usb_detach_device() was freeing and
NULLing out the pointer. That results in all callers who
needed that object to start accessing random bits of memory.
This eventually led into free()ing memory it shouldn't which
corrupted the allocator's state. Eventually, all forward
progress was lost by way of a single ended linked list
turning into a circular list.
The culprit seems to be a bad merge in commit e00ba21.
BUG=chrome-os-partner:43419
BRANCH=None
TEST=Can boot into OS now w/o "hanging" on glados.
Original-Change-Id: I86dcaa1dbaf112ac6782e90dad40f0932f273a1f
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/290048
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9135eb0f798bf7dbeccc7a033c3f8471720a0de5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11173
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Changqi Hu