This patch adds support for the Fintek F81866AD-I SuperIO,
which is very similar to the fintek/f81865f.
This code adds some fan control support, inspired by fintek/f71869ad.
Furthermore its possible to change the temp sensor type (thermistor or diode).
Datasheet: Name: F81866D/A-I, Release Date: Jan 2012, Version: V0.12P
Link: http://www.alldatasheet.com/datasheet-pdf/pdf/459085/FINTEK/F81866AD-I.html
Change-Id: Id2fc1119b37142f8101f71908e394ee69c45041d
Signed-off-by: Fabian Kunkel <fabi@adv.bruhnspace.com>
Reviewed-on: http://review.coreboot.org/10287
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Initialization for the Winbond W631GG6KB part using Synopsys
DDR uMCTL and DDR Phy.
This code adds a separate function for DDR3 initialization
and moves all the necessary defines in a separate header file.
The programming procedure that is executed at power up to bring
up the uMCTL, PHY and memories into a state where reads and
writes to the memory can be performed is the following:
1. uPCTL (Universal DDR protocol controller) initialization
The timining registers TOGCNT1U, TINIT, TOGCNT100N and TRSTH
needed for driving the memory power-up sequence are programmed
as a function of the internal timers clock frequency.
Organization (memory chip specific) values are set
(column/bank/row address width and number of ranks), together
with other static values (latency, timing, power up configuration).
All these values are static, provided by the datasheet,
being determined by the memory type, size and frequency.
2. PHY initialization
The PHY is programmed with datasheet provided values,
specifying the initialization values for it to send to the
external memory (timing parameters).
Also, delay lines (DLL) and strength of drive pads are
calibrated (based on external conditions: temperature,
voltage, noise) and locked. After that, the PHY goes
through a trainig process (also dependent on the
current conditions at boot time) to establish precise
timing configuration between the DDR clock and DQS (data strobe)
and between DQS and DQ (data).
3. Memory power up
4. Switch from configuration state to access state.
It was tested on Pistachio bring up board where DDR was initialized
properly and ramstage executed correctly
Change-Id: I3bcbce2044327a22fce09b184d85ee11228a6b2b
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/10529
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Switching from active windowing DQS gating scheme to
passive windowing mode resolves boot stability issues
on chips found to have memory corruption issues during
boot or memory tests.
It was tested on Pistachio bring up board where DDR is
initialized properly and ramstage executed correctly;
We have cycled units over 12,000 times with no boot errors.
This option was chosen over the alternative of using
passive windowing mode for DQS training and after switching
back to active mode, as this option was recommended by
Synopsys. Using the alternative would give different
timing values during training that were not longer accurate
during normal activity.
Change-Id: Ie604eddc0a9a982b2f89198f44deb88a01b7b322
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/10528
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix by checking the actual function return value (the search
address pointer), rather than the search length value (which isn't
guaranteed to be sane or useful).
Change-Id: I226c635ddbbc916b02494fcd97df27d141cc2c7f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: http://review.coreboot.org/10516
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
The precise phrase returned by 'type' differs between locales and shells.
It also doesn't matter because it returns an error code when it hasn't found a
match.
Let's simply assume there's no build_$OneOfOurPackages commands around that
could also match.
Change-Id: I44f021243149701e8da9dd74c368ca2ad4509419
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Tested-on: linux bash, linux dash, solaris sh, solaris ksh.
Reviewed-on: http://review.coreboot.org/10517
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ic6ce697af6102da7d8c53947c9d3b5ac39817d7c
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10333
Tested-by: build bot (Jenkins)
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Commit 899d13d (cbfs: new API and better program loading) broke
panther's lan init when no vpd.bin present from which to read
the MAC address. Fix this by checking the validity of the search
address pointer, rather than the search length.
Change-Id: I8c7ca410d8ce5c5d92242a21c4c2ff4c001a68bd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: http://review.coreboot.org/10509
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
libpayload is the only Kconfig based project under
the coreboot umbrella that is using Config.in as its
name for Kconfig config files. Rename that to Kconfig
as on the other projects for consistency.
Change-Id: I1c69ec13582d88409384b492484535dcc5e1ad20
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10520
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
using grep is an extra process invocation, but it's not a bashism.
Also match precisely, so AGCC doesn't trigger on GCC (we don't have collisions
right now, but we won't have to deal with them in the future)
Change-Id: I242833c350b7f1e6a6793f288c1aae0b50d57a26
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10518
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The proper log level for any given printk statement is up to the
interpretation of the developer. This results in console output with
somewhat inconsistent levels of verbosity. This patch clearly defines each
log level and its use case, hopefully resulting in less ambiguity for
developers.
The concern with this patch might be that it leaves a lot of preexisting
printk statements using a log level that is inconsistent with the
description. I think that *most* statements map to these extended
definitions very nicely. The most discrepancies are between debug and
spew, but I'm willing to say that 95% of statements with a level lower than
debug are correct by these definitions.
There was some discussion dating back to 2010 on the mailing list about
renaming these constants to lose the 'BIOS_' prefix and to consolidate
some of them into a single constant. I disagree that it is necessary
to merge any of them, I think they all have unique use cases. But I do
think that if you all agree with these definitions, it might be useful to
rename them to reflect their use cases.
I also will add that I believe removing BIOS_NEVER is a good idea. I do
not see the use case, and it's used in only 4 files.
Change-Id: I8aefdd9dee4cb4ad2fc78ee7133a93f8ddf0720b
Signed-off-by: Nicky Sielicki <nlsielicki@wisc.edu>
Reviewed-on: http://review.coreboot.org/10444
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
New marker includes:
3d5af98 microcode: Update Broadwell to MC0306D4_0000001F
349fd55 microcode: Update Baytrail to M0C30678_000082D
9077293 Add BLOBs to support AMD Embedded "Merlin Falcon" processor
Change-Id: I53f8f95079c6436ad316a11d432fcf92c03332b5
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/10506
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Locales differ in the order in which they sort entries. This ensures
predictable behavior.
Change-Id: I4ceec90a56bbc368a847d14298db0a21cc21e77c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10510
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It's derived from EEPROM on Lenovo machines and not from user config
which is ignored.
Change-Id: I54fb76a3160e47cd36d33d2937c4bfaddcd36a69
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7055
Tested-by: build bot (Jenkins)
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
This change adds cache management after loading stages.
Before jumping to a new stage we should flush the data
caches to memory and invalidate instruction cache.
After all segments are loaded CBFS cache is also
flushed.
With this change all stages of coreboot are now executed
successfully. This was tested on Pistachio bring up board,
also known as Urara.
Change-Id: I86e07432c21a803ef1cfc41b633c5df42b99de90
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/10456
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The coreboot table address is passed as an argument when jumping
to payload.
With this change depthcharge is loaded and executed properly on urara.
Change-Id: I230d474a91b8d38aff070aa4aac623b6c8f0809c
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/10460
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Place included header files in alphabetical order.
Change-Id: Ice23178d1f07e2cb0178efbc7ce487d54bf3f708
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/10459
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Use cbmem_initialize_empty() after DDR configuration so that
cbmem is always initialized from scratch on each boot.
Change-Id: Ic9ca34867b26aab82cf3154280694b6fb61ee11f
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/10458
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
sata.asl and superio.asl are empty files. Remove them.
Change-Id: Icd3e990aa713281e46dcbd8e0847166c77656b1c
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Reviewed-on: http://review.coreboot.org/10505
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The default ordering for the base kconfig entries has the CPU
directory coming before the SOC directory, which means that the
values in the CPU Kconfig take precedence.
The first visible consequence of this is that CONFIG_SMM_TSEG_SIZE
will be set to 0 on all SOC implementations.
BUG=chrome-os-partner:40635
BRANCH=none
TEST=build and boot on glados
Change-Id: Ifd56a2ceb73ab335a86126e48d35ff4c749990ac
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0cddae37d3de1cbf3dd6afcf4a0707b7af9436fa
Original-Change-Id: I98e3bf249650b50667dde62b6be9c1bf587ad0b2
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/276189
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10478
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Copy the Peppy directory. No changes.
Change-Id: I3fa382eaa40f642df8bc09ab69be67cbe9f3671a
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/10499
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Build with bfd and gold linker, but use bfd linker per default
and make sure that lto is enabled in both binutils and gcc
Change-Id: I0584396b4580674cfdca24fbed0d8eeb1ee38806
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10496
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Instead of building IASL and GDB implicitly when building
GCC, this patch changes buildgcc to let you explicitly specify
what you want to build.
This will prevent IASL from building over and over again, when
all you need is GDB.
The new command line option is -P | --package <package> where
package is one of the following: GCC, GDB, CLANG, IASL
If no package is specified, buildgcc will default to GCC.
Change-Id: I8836bed16fc2bc39e0951199143581cc6d71cb4d
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10492
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The type1 family setting from chromium was mis-merged into the
type2 function. Move it to the correct type1 function.
Bad commit: 51bdc47816
Change-Id: I72e6ef80bbf185a39fcf169c8247dc16462e6bc3
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/10498
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
IASL was broken when compiling without GCC.
Change-Id: Ib859ce41c1dda10181781c025fc378504f5ebb91
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10495
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
GDB stopped building ever since we updated from version 7.6
but nobody noticed ;)
Update from 7.9 to 7.9.1 and bring the required patches forward.
Change-Id: I2f357525a46d5540e9f57b80d830943bbd5dfcaf
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10494
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
This groups all tasks happening in the main program,
orders them according to their dependencies and adds
comments on the various tasks.
Change-Id: Ib62bd213977cbc3307ef62e9a7e64515563968c1
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10490
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins)
- don't capture build_$package in a subshell by piping it
- move HOSTCFLAGS to build_GMP
- only create a build directory if a build happens
- automatically collect packages to build
Change-Id: Ic5a9f3f222faecd3381b413e5f25dff87262a855
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10475
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins)
The type of a resource is really an enumeration but our implementation
is as a bitmask. Compare all relevant bits and remove the shadowed
declarations of IORESOURCE bits.
Change-Id: I7f605d72ea702eb4fa6019ca1297f98d240c4f1a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8891
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
No board in the tree selects this and it looks like the implementation
was done at chipset level while it should be part of PCI subsystem.
When enabled, at least AMD K8 and f14, f15tn and f16kb fail build test.
Feature of placing prefetchable PCI memory above 4GB may not work if
there is any 32-bit only prefetchable PCI BARs in the system.
Change-Id: I40ded2c7d6d05f461423721aa5d78a78f9f9ce1e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8705
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
On modern mainboards with multiple PCI-e devices and a single
graphics card the default MMIO hole size of 512M is inadequate,
leading to resource-hungry PCI-e devices (such as an external
graphics card) being assigned invalid MMIO ranges. This, in
turn, causes the entire PCI subsystem to become unavailable,
leading to a failure to boot.
TEST: Booted KGPE-D16 with NVIDIA 7300LE and verified proper
operation of PCI/PCI-e devices, including text mode VGA operation
via the add-on card and its VGA option ROM.
Change-Id: I8d25f4b19f2d0860644ab1ee002c15041437121f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/10428
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add a savedefconfig target and the help for it to the kconfig
makefile.
The main advantage I found for using defconfigs instead of the full
.config is that they require less maintenence, so long as reasonable
default values are set when adding new config options. When the
defconfig is expanded, it will use default values for all options not
saved in the defconfig. This cuts the size of a saved config from
500ish lines to roughly 20 lines.
savedefconfig was added to the linux kernel in commit id
7cf3d73b4360e91b14326632ab1aeda4cb26308d
Change-Id: I45f3dc87b773fb6e9ee53e32fdcafff1f53074d2
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10462
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Bring gdb in sync with all other build targets.
Change-Id: I9c478947a00f044edf910a91d876bbf486a791cf
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10488
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Otherwise one could end up with what they think is a coreboot toolchain
but in fact it'd be missing some patches.
Change-Id: Ic451f7061b822d0f4b64acc9976ba81fd544e85b
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10487
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
gcc and binutils fixed their upstream tar balls, and running
autoconf created more problems than it solved
Change-Id: I0003dd597f521701405ff35923214435136b262d
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10486
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Change-Id: I29fe23e377045f08b8212742d84c2ee2b4a61b15
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10485
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Change-Id: I7a095470d408d013a4a915e010c59ea99ca1f1c8
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10484
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Fabian Kunkel