and disable IO mapped UARTs on ARMV7 per default
Change-Id: I712c4677cbc8519323970556718f9bb6327d83c8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2021
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The oxpcie ramstage code calls uartmem_init after the PCI memory
allocation, but hte function was static and didn't have a prototype.
Change-Id: Iabc1a3d248aeaed29aaaa22504defac97c572326
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1285
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Use an int in CAR global data to store whether or not the OXPCIE serial card
is actually there. Also, time out if the card doesn't show up quickly enough,
don't continue initialization if it's not there, and don't make the
initialization routine default to a card if none is found.
Change-Id: I9c72d3abc6ee2867b77ab2f2180e6f01f647af8c
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/728
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Because it's included everywhere anyways.
Change-Id: I99a9e6edac08df57c50ef3a706fdbd395cad0abc
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/691
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add information about memory mapped/io mapped base addresses.
and fix up libpayload to use the same structures
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I5f7b5eda6063261b9acb7a46310172d4a5471dfb
Reviewed-on: http://review.coreboot.org/261
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The previous code does a full flush of the uart after every character.
Unfortunately, this can cause transmission delays on some serial
ports.
This patch changes the code so that it does a flush at the end of
every printk instead of at the end of every character. This reduces
the time it takes to transmit serial messages (up to 9% on my Asrock
e350m1 board). It also makes the transmission time more consistent
which is important when performing timing tests via serial
transmissions.
Change-Id: I6b28488b905da68c6d68d7c517cc743cde567d70
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Reviewed-on: http://review.coreboot.org/90
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-by: Sven Schnelle <svens@stackframe.org>
example.
This newer version reflects the recent changes to further simplify the console
code and partly gets rid of some hacks in the previous version.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6544 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and baudrate, not hardcoded in addition to that.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6538 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot made it kind of complicated to print a character on serial. Not quite
as complicated as UEFI, but too much for a good design. Fix it.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6191 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Reworked pnp superio device support. Now complete superio support is less than 100 lines.
- Added support for hard coding resource assignments in Config.lb
- Minor bug fixes to romcc
- Initial support for catching the x86 processor BIST error codes. I've only seen
this trigger once in production during a very suspcious reset but...
- added raminit_test to test the code paths in raminit.c for the Opteron
- Removed the IORESOURCE_SET bit and added IORESOURCE_ASSIGNED and IORESOURCE_STORED
so we can tell what we have really done.
- Added generic AGP/IOMMU setting code to x86
- Added an implementation of memmove and removed reserved identifiers from memcpy
- Added minimal support for booting on pre b3 stepping K8 cores
- Moved the checksum on amd8111 boards because our default location was on top of
extended RTC registers
- On the Hdama added support for enabling i2c hub so we can get at the temperature
sensors. Not that i2c bus was implemented well enough to make that useful.
- Redid the Opteron port so we should only need one reset and most of memory initialization
is done in cpu_fixup. This is much, much faster.
- Attempted to make the VGA IO region assigment work. The code seems to work now...
- Redid the error handling in amdk8/raminit.c to distinguish between a bad value
and a smbus error, and moved memory clearing out to cpufixup.
- Removed CONFIG_KEYBOARD as it was useless. See pc87360/superio.c for how to
setup a legacy keyboard properly.
- Reworked the register values for standard hardware, moving the defintions from
chip.h into the headers of the initialization routines. This is much saner
and is actually implemented.
- Made the hdama port an under clockers BIOS. I debuged so many interesting problems.
- On amd8111_lpc added setup of architectural/legacy hardware
- Enabled PCI error reporting as much as possible.
- Enhanded build_opt_tbl to generate a header of the cmos option locations so
that romcc compiled code can query the cmos options.
- In romcc gracefully handle function names that degenerate into function pointers
- Bumped the version to 1.1.6 as we are getting closer to 2.0
TODO finish optimizing the HT links of non dual boards
TODO make all Opteron board work again
TODO convert all superio devices to use the new helpers
TODO convert the via/epia to freebios2 conventions
TODO cpu fixup/setup by cpu type
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1390 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
