W83627DHG:
- Add proper "virtual LDN" handling for the LDNs that need it (i.e., those
that don't have their "enable" bit in bit 0 of the 0x30 register).
- Fix various I/O masks in the pnp_dev_info[] array as per
datasheet. Add missing PNP_IRQ0 to the W83627DHG_ACPI LDN.
W83627EHG:
- Similar to W83627DHG, improve the "virtual LDN" setup a bit (it was
mostly implemented already, though).
- Add missing PNP_IRQ0 to the W83627EHG_ACPI LDN.
Also: Fix up devicetree.cb of all boards using W83627DHG/W83627EHG to adapt
for the virtual LDNs.
include/device/pnp.h: Add comment that 'function' (which refers to the
LDN and should probably be renamed later) has to be at least 16 bits
wide. In theory LDNs could use u8, but due to the virtual LDN info being
encoded in the "high byte" of 'function' it must be at least u16.
asrock/939a785gmh/romstage.c: Drop unused GPIO6_DEV.
ibase/mb899/romstage.c: Use DUMMY_DEV instead of a specific LDN (serial
port 1 in this case) to avoid confusion. The global registers
manipulated there are accessible from any LDN.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6140 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Whitespace and indentation fixes in various places.
- Fix various typos.
- Use u8, u16 etc. everywhere.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5962 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- drop include/part and move files to include/
- get rid lots of warnings
- make resource allocator happy with w83627thg
- trivial cbmem resume fix
- fix payload and log level settings in abuild
- fix kontron mptable for virtual wire mode
- drop some dead includes and dead code.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5136 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Use the (almost) same strict CFLAGS in v2 that we use on v3. And fix a few
include files and missing prototypes. Also, fix up the Config-abuild.lb files
to properly work for cross compiling.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4000 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Reworked pnp superio device support. Now complete superio support is less than 100 lines.
- Added support for hard coding resource assignments in Config.lb
- Minor bug fixes to romcc
- Initial support for catching the x86 processor BIST error codes. I've only seen
this trigger once in production during a very suspcious reset but...
- added raminit_test to test the code paths in raminit.c for the Opteron
- Removed the IORESOURCE_SET bit and added IORESOURCE_ASSIGNED and IORESOURCE_STORED
so we can tell what we have really done.
- Added generic AGP/IOMMU setting code to x86
- Added an implementation of memmove and removed reserved identifiers from memcpy
- Added minimal support for booting on pre b3 stepping K8 cores
- Moved the checksum on amd8111 boards because our default location was on top of
extended RTC registers
- On the Hdama added support for enabling i2c hub so we can get at the temperature
sensors. Not that i2c bus was implemented well enough to make that useful.
- Redid the Opteron port so we should only need one reset and most of memory initialization
is done in cpu_fixup. This is much, much faster.
- Attempted to make the VGA IO region assigment work. The code seems to work now...
- Redid the error handling in amdk8/raminit.c to distinguish between a bad value
and a smbus error, and moved memory clearing out to cpufixup.
- Removed CONFIG_KEYBOARD as it was useless. See pc87360/superio.c for how to
setup a legacy keyboard properly.
- Reworked the register values for standard hardware, moving the defintions from
chip.h into the headers of the initialization routines. This is much saner
and is actually implemented.
- Made the hdama port an under clockers BIOS. I debuged so many interesting problems.
- On amd8111_lpc added setup of architectural/legacy hardware
- Enabled PCI error reporting as much as possible.
- Enhanded build_opt_tbl to generate a header of the cmos option locations so
that romcc compiled code can query the cmos options.
- In romcc gracefully handle function names that degenerate into function pointers
- Bumped the version to 1.1.6 as we are getting closer to 2.0
TODO finish optimizing the HT links of non dual boards
TODO make all Opteron board work again
TODO convert all superio devices to use the new helpers
TODO convert the via/epia to freebios2 conventions
TODO cpu fixup/setup by cpu type
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1390 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Changes to allow more code to be compiled both ways
- Working SMP support
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@987 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
