The display port bridge on pit is different from the one on snow and needs to
be initialized differently. Instead of waiting for the chip to come up on its
own and assert the hotplug detect, we need to access it over i2c and get it up
and running ourselves.
Change-Id: I4bc911cb8e4463edff7beabd2f356cb70ae9f507
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3723
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This driver is basically the same as the one in U-Boot but without the device
tree stuff. That driver is, in turn, a straightforward implementation of the
sequence of register writes described in the data sheet. Comments were added
in U-Boot which helpfully describe what the register writes are actually
doing and are kept.
Change-Id: I64ba6b373478853bb2120f0553a43de901170d02
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/3753
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Data is intended to be a byte array, so it should be described by a type which
has a fixed size equal to an 8 bit byte. Also, the data passed to write
shouldn't be modified and can be const.
Change-Id: I6466303d962998f6c37c2d4006a39c2d79a235c1
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3721
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This was removed from ramstage a little while ago and should have been removed
from here as well.
Change-Id: I6a40ed4a98bedac39e5492e4b1aed3427ab4e08b
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3720
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This appears to be needed, though we have no way to test yet.
Change-Id: I39033581011e056258193f2cdff78814361a8d55
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3719
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In resume path, if memory setup takes too long without setting PS_HOLD, EC watch
dog may power off or reboot the system. To prevent that, we should enable
PS_HOLD in same timing as cold boot - right before starting memory setup.
Change-Id: I5c294fa7ae015f8cff57b1fd81e5b80902647b15
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3718
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The functions which manipulated the tps65090 were removed a while ago because
it isn't accessible directly from the AP, it's on an I2C bus that has to be
accessed by the EC on our behalf. Now that that capability has been added, we
can rewrite the small portion of the the tps65090 we actually used but using
the EC passthrough commands.
Also, we should not be configuring the hardware display port hotplug detect
line since we're using it as a GPIO for other purposes. The GPIO we're using
instead defaults to being an input, but to be safe we should probably
explicitly configure it as one anyway.
Change-Id: I7f8a8a767e3cccb813513940a5feceea482982f5
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3717
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The ChromeOS EC for peach_pit is connected to SPI2 bus, not I2C.
Change-Id: Ifeb8a626aa4fc3d3a181a7bc016e3f91be948ae5
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3716
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The workaround of re-opening device in exynos_spi_read has been fixed by the new
correct open/close and xfer procedure. It's safe to be removed now.
Change-Id: I6b1bf717c916903999a137998a578b0a866829bd
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3715
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Switch spi_xfer and exynos_spi_read to use the new spi_rx_tx function.
Change-Id: I01ab43509df1319672bec30dd111f98001d655d0
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3714
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The SPI driver (exynos_spi_rx_tx) was implemented with only "read" ability and
only full-duplex mode. To communicate with devices like ChromeOS EC, we need
both output (tx) and half-duplex (searching frame header) features.
This commit adds a spi_rx_tx that can handle all cases we need.
Change-Id: I6aba3839eb0711d49c143dc0620245c0dfe782d8
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3713
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The original Exynos SPI open/close procedure was copied from U-Boot SPL with
some assumptions that only works in SPL stage. For example, it tries to always
work in 4-byte transmission mode with only RX data is swapped, and claims a
packet for initial address command (and with incorrect size).
This commit revises open/close and reset so only the required SPI registers are
configured.
Change-Id: Ieba1f03d80a8949c39a6658218831ded39853744
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3712
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fill the SPI device parameters for spi_setup_slave on Exynos 5420.
Change-Id: I10b4b9e6cfe46d7bfa34e80e3727c7e7da99ba9d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3711
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The SPI module in Exynos 5420 didn't follow Coreboot's SPI API standard
(spi-generic.h) and will be a problem when we want to share SPI drivers.
This commit replaces exynos_spi_* by spi_* functions.
Note, exynos_spi_read is kept and changed to a static function because its usage
is different from the standard API "spi_xfer".
Change-Id: I6de301bc6b46a09f87b0336c60247fedbe844ca3
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3710
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Remove unused header and constant definition in SPI module.
Change-Id: I339e603f48186e4a356e83518b0d0b4c907f11b8
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3709
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add SPI0 and SPI2 to Exynos 5 SPI list, and correct structure names.
Also removed the un-enumerated devices (SPI_BASE, base_spi()).
Change-Id: Ica6d9a41f9619c8c61eab664d5e988dd4a428e09
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3708
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
For devices with ChromeOS EC on SPI bus, use the standard SPI driver interface
(see spi-generic.h) to exchange data.
Note: Only EC protocol v3 is supported for SPI bus.
Change-Id: Ia8dcdecd125a2bd7424d0c7560e046b6d6988a03
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3751
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add the new Chrome EC protocol version 3 to Coreboot.
Note, protocol version 3 is not applied on any bus implementations yet.
LPC (x86) and I2C (arm/snow) are still using v2 protocol. The first one to use
v3 protocol will be SPI bus (arm/pit). LPC / I2C will be updated to v3 only
when they are ready to change.
Change-Id: I3006435295fb509c6351afbb97de0fcedcb1d8c4
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3750
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Since EC protocol v3, the packet format will be the same for all buses (inclding
I2C, SPI, and LPC). That will simplify the implementation in each individual bus
driver source file.
To prepare for that, we will move the protocol part into crosec_proto.c:
crosec_command_proto, with bus driver in callback "crosec_io".
Change-Id: I9ccd19a57a182899dd1ef1cd90598679c1546295
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3749
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The Embedded Controller (EC) for Pit is connected via SPI2, and needs to be
configured before we can talk to it.
Change-Id: I1f8e921b4616f15951f3e5fae1ecbf116de4ba90
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3707
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Some initialization / shutdown commands should be paired correctly in a SPI I/O
session. For example, setting CS should be enabled and disabled in each read;
and the bus width (byte or word) should be configured only when opening /
closing the SPI device.
Change-Id: Ie56b1c3a6df7d542f7ea8f1193ac435987f937ba
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3706
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I4feabc448945c4664d3114c0c8afdad48338230a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3705
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The functions which checked the status of a transfer would return success if
the bus was no longer occupied, even if it's no longer occupied because the
transfer failed. This change modifies those functions to return three possible
values, 0 if the transfer isn't done, -1 if there was a fault, and 1 if the
transaction completed successfully.
Change-Id: Idcc5fdf73cab3c3ece0e96f14113a216db289e05
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3704
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The exynos manual suggests hooking the mmc ip blocks to the mpll. They had
been set to use a different pll. This changes them over and modifies the
divider so that the frequency stays the same.
Change-Id: I85103388d6cc2c63d1ca004654fc08fcc8929962
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3703
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This allows us to set different speeds for each HSI2C bus.
Change-Id: I50cc257aad9ef50025d0837b0516940b956efc02
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3701
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change adjusts some clock settings so that they match U-Boot. There are
three different changes.
1. Change the source for psgen from the oscillator clock to the pclk.
2. Change the pll feeding the SPI busses from epll to mpll, as suggested in
the manual.
3. Change the SPI prescaller.
Change-Id: Ib54a255bc14fc286629dac86db9b8cf8e75a610b
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3700
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The clock divider was being read from registers incorrectly which meant that
the periph rate was wrong.
Change-Id: I50efb62849ef29bdfb0efc56c49642d3edca094c
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3699
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Wait for UART FIFO to be ready.
(Credit to dhendrix for finding the bits to test with.)
Change-Id: Ib6733e422cbc1c61b942bd90d85f88a3f412d6ff
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3698
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Chrome EC protocol V3 has several new command structure and constants defined.
Simply cherry-picking changes from upstream.
Change-Id: I7cb61d3b632ff32743e4fa312e0cc691c1c4c663
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3748
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
... this is needed for libpayload to talk to USB devices.
(forward ported from https://gerrit.chromium.org/gerrit/#/c/55554)
Change-Id: I5a20864689efd0c0149775e6d85b658e0cc6715c
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3697
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
... this is needed for libpayload to talk to USB devices.
Change-Id: I7eb19003c9e96efb5fa7a3f97c7b15f3ef332687
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3696
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I5cddffc2e524aae7a31a8f94f67e03a5b7e15c82
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3695
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Otherwise we have to worry about hand off between bootblock and
romstage. Too much complexity
Change-Id: I89bf8a229dba7e1330accadf9a732d831ebc4827
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3694
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is already called in ARMv7 bootblock_simple.c so we don't
want to do it twice
Change-Id: I80cb41035b8a77787e04f2ea58a1cd372cea97d8
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3692
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I6b28bb95c7decbe3eed33b5b5a029bee48bbe403
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3691
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Currently, the exception handling code on ARM turns on alignment checks as an
easy way to generate an exception for testing purposes. It was leaving it on
which disabled unaligned accesses for other, unlreated code running later.
This change adjusts the code so the original value of the alignment bit is
restored after the test exception.
Change-Id: Id8d035a05175f9fb13de547ab4aa5496d681d30c
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3690
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The GPIOs used by vboot and setting up the display and backlight were still
the ones for snow. This change updates them so they're correct for pit.
Change-Id: I06ba773da3af249efec723bb90c2e9e8075a777a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3689
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The MAX_CPUS option is only used on x86 currently, so there's no reason to
have it in the pit config.
Change-Id: I270bbfd3aff781d88304791b1d9735777643caab
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3688
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
That part isn't used on pit.
Change-Id: I48f3a10f7e6eb89b1e9630d2372b6865b4c12a7f
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3687
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
On pit, the tps65090 is connected to the EC and has to be accessed by proxy.
Until we have that implemented, this change removes calls to tps69050 which
will never succeed, and stops compiling in the driver.
Change-Id: I7218f85f9f26623bd13aaaf8ded0638b3b2f874a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3686
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The members data structures in dmc.h are intended to have a particular size.
Rather than assume that particular types are the right size, we should use
types that are guaranteed to be the right size. Also, since the registers are
at particular offsets as well, the structures should be packed.
Change-Id: I9cc11d7451f92ba3eb85c6be88ecbc62c7a5652d
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3685
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The previous driver was a bit awkward and not entirely correct. This change
primarily replaces the read/write functions with simpler and more robust
(hopefully) version.
Change-Id: I55f0ad8faec2de520e27577bd6dad9c0118d8171
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3684
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
For all other CPUs, we unconditionally include the CPU Kconfig
files in the CPU directory, not in the vendor directory. Do the
same thing for the Exynos CPUs. This allows us to make CPU dependent
changes in the directory of that CPU alone.
Also, drop some unused Kconfig variables from the Exynos Kconfig
files.
Change-Id: I4e4c22a0693988834e619dd33d121bf994ed57e8
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3683
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The dmb should be executed before reading operations, and before/after writing
operations.
Change-Id: I572136a2f9a07eb2c38a112f5deeb2de0c0fd46c
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3682
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This updates the low-level I2C code to handle the new high-speed
HSI2C/USI inteface. It also outputs a bit more error information
when things go wrong. Also adds some more error prints. Timeouts
really need to be noted.
In hsi2c_wait_for_irq, order the delay so that we do an initial
sleep first to avoid an early-test that was kicking us out of the
test too soon. We got to the test before the hardware was ready
for us. Finally, test clearing the interrupt status register every time
we wait for it on the write. Works.
Change-Id: I69500eedad58ae0c6405164fbeee89b6a4c6ec6c
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3681
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Gabe Black