In order to support probing I2C devices when the controller is
in ACPI mode the mainboard needs to decalre them in the proper
scope with the address/interrupt information. The touchpad devices
are ATML0000/ELAN0000 and the touchscreen is ATML0001 so they can
be distinguished in userland scripts based on ID. There is also
a special "ISTP" node that indicates whether the devices is a
touchpad (=1) or touchscreen (=0) in case this is useful to drivers.
These names may not be final but they are a starting point and can
be easily changed.
Atmel devices also have a bootloader mode which needs to be
declared as a separate device. Unfortunately it does not work as
expected to have multiple I2cSerialBus() resources declared in a
single device and have it select properly, even with the use of
StartDependentFn(), so bootloader devices are declared separately.
The original devices are left in \_SB scope and are only enabled
if the I2C controllers are in PCI mode. The new devices are only
enabled if the I2C controllers are in ACPI mode.
BUG=chrome-os-partner:24380
BRANCH=baytrail
TEST=manual
1) Ensure there is no change in functionality by default and that
the devices are still probed by chromeos_laptop in the kernel.
2) Enable lpss_acpi_mode=1 in devicetree.cb and kernel changes to
add _HID entries for devices in appropriate drivers. Ensure that
the devices are probed successfully. Further changes are needed
to the chromeos-touch-firmware scripts to load config and update
firmware based on the new ACPI _HID entries.
3) Put touchpad in bootloader mode (by flashing bad firmware) and
ensure that it is detected at address 0x25 and the firmware is
able to be updated.
Change-Id: I5b9b47ddc94474a677497271e963f62cb09438e0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/182259
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5045
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This enables the DPTF framework, but it doesn't do much
without some sort of kernel+user components to drive it.
BUG=chrome-os-partner:17279
BRANCH=none
TEST=build and boot on rambi, dump DSDT and look over \_SB.DPTF
Change-Id: Icb632a6e70c3912bbdfa6ef3f5c87cd79d2b8a3a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179480
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5003
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This provides the initial support for interrupt routing
in bay trail. It includes both acpi changes and board changes
to ensure the interdependencies are met with the current ASL
code. The PIRQ routing is handled by the mainboard exporting
an irqroute.h header that describes the per device and PIRQ
PCI settings.
There are still a lot of ACPI errors in the kernel with this
change, though.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Built and booted rambi into kernel.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Id8a865a24fc8d49743c0b54efdb64aaef52fcd8e
Reviewed-on: https://chromium-review.googlesource.com/175700
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4940
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add a length define for all the reserved MMIO regions and
use them in the ACPI code to reserve the regions there.
Add a region for the "abort page" documented in the EDS.
BUG=chrome-os-partner:23505
BRANCH=rambi
TEST=build and boot on rambi
Change-Id: I2060dca0636a2fdc0533ddd0826f94add2c272c3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175624
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4934
Tested-by: build bot (Jenkins)
