The one USB2 port on the XHCI2 controller should have the port ID 2.0,
since it's the first USB2 port on that XHCI controller.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4a370132960939bccec4eb69a6590d0880b04137
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62713
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GFX HDA is the audio controller that provides audio output via the
external display connection, ACP is the audio coporcessor for the on-
board audio codec and XHCI2 is the third XHCI controller that provides
one USB 2.0 port. All those devices are used, so enable them in the
board's devicetree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I186797a832470eb17752e06aa2fcc0b5c9db0398
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62571
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Select GL9750 driver and add power sequence according to datasheet:
GL9750S-OIY04 rev1.22.
BUG=b:223304292
TEST=check GL9750 can get enumerated by kernel 5.15.
01:00.0 SD Host controller: Genesys Logic, Inc Device 9750 (rev 01)
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ib6d461a56f6aeba30994daafe8993c36df4b309d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Enable pen garage. Pen detect is active low. And wake system when
eject.
BUG=b:223476974
TEST=evtest work as expected.
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "PRP0001:00"
Supported events:
Event type 0 (EV_SYN)
Event type 5 (EV_SW)
Event code 15 (SW_PEN_INSERTED) state 0
Properties:
Testing ... (interrupt to exit)
Event: type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Event: -------------- SYN_REPORT ------------
Event: type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I2f676301c3372a4760853ce9c10b75f94e22bbcd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
This change mostly changes links that were identified as broken by
the 'website_scans' jenkins job.
There were some links that seem to be up at times, but that are
identified by link-checker as broken because of SSL issues.
At least one other link was changed to point to archive.org so
that it doesn't break at some point in the future. We should
probably try to make sure that everything is archived there and
point to those versions when possible.
There are still lots more links to do.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I36868ddf6113e18fa6841427dd635c75445b7bef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
There is no need that the tutorial for flashing firmware has its own
point in the main menu. Thus, move it to the tutorial section.
Change-Id: Ife6d97254af4c006fe01480a78c76303f9cb34bb
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Thomas Heijligen <src@posteo.de>
In preperation for CB:62424, replace HTTP links pointing to the flashing
firmware tutorial with file paths to the Markdown files.
Change-Id: I6a271a912348cbe002bc9cced9922ed743e1133c
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Thomas Heijligen <src@posteo.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Only one ACPI device should be added to a PCIe root port. For the root
ports which already have device created, the generated code from this
driver needs to be merged with the existing device.
By default, this driver will create new device named DEV0.
This change allows to generate code under an existing device.
ex: (generate code under PXSX):
Scope (\_SB.PCI0.RP01.PXSX)
{
Name (_DSD, Package (0x02) // _DSD: Device-Specific Data
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301")
Package (0x01)
{
Package (0x02)
{
"UntrustedDevice",
One
}
}
})
}
BUG=b:221250331
BRANCH=firmware-brya-14505.B
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I80634bbfc2927f26f2a55a9c244eca517c437079
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Since the new loglevel markers were added, there will now be a marker
character at the beginning of the coreboot banner string, and this will
make the existing regular expressions meant to find it fail to match.
This patch fixes the problem by just allowing for a single extra
character there (any character to avoid the hassle of having to match
the marker explicitly). The extra character is optional so that we will
still continue to match banners from older versions of coreboot as well.
Since the `?` glyph is not available in basic POSIX regular expressions,
we have to switch to REG_EXTENDED syntax (should otherwise make no
difference). (Also, move side effects out of assert() while I'm here,
that's not actually safe for the standard libc implementation.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I99fb347eb1cf7b043a2113dfda7c798d6ee38975
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62720
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Get boot performance timestamps from CSE and inject them into CBMEM
timestamp table after normalizing to the zero-point value. Although
consumer CSE sku also supports this feature, it was validated on
CSE Lite sku only.
BUG=b:182575295
TEST=Able to see TS elapse prior to IA reset on Brya/Redrix
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 88,000
945:CSE started to handle ICC configuration 88,000 (0)
946:CSE sent 'Host BIOS Prep Done' to PMC 90,000 (2,000)
947:CSE received 'CPU Reset Done Ack sent' from PMC 282,000 (192,000)
0:1st timestamp 330,857 (48,857)
11:start of bootblock 341,811 (10,953)
12:end of bootblock 349,299 (7,487)
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Idcdbb69538ca2977cd97ce1ef9b211ff6510a3f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
GPIO 32 was not allocated correctly, updating to reflect the native
function use of the pin
BUG=b:214412172
TEST=Builds
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: Idadd2a802b3244eba8ee83f80d8f10baebe4ca40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62717
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to copy the PSP verstage logs into x86 cbmem, we need to enable
DEBUG_SMI. This will include the CBMEM console code in SMM. I only
enable DEBUG_SMI when UART is disabled because SMM doesn't currently
save/restore the UART registers. This will result in clearing the
interrupt enable bits and makes it so you can no longer use the TTY.
BUG=b:221231786, b:217968734
BRANCH=guybrush
TEST=Build serial and non serial firmware and verify DEBUG_SMI is set
correctly.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I85a7933e8eb49ff920d00e43a494aaeab555ef3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Now that SMM can write to CBMEM we can simply replay the transfer buffer
cbmem console to move it into the main cbmem console.
replay_transfer_buffer_cbmemc() relies on the EARLY_RAM linker symbols.
Since the SMM rmodule get linked with a different linker script than
bootblock/romstage it doesn't have access to these symbols. In order to
pass these symbols into SMM, we parse the bootblock.map file and
generate an early_ram.ld script. This script is then used when linking
SMM.
I replay the buffer in `smm_soc_early_init` because this call happens
before `console_init()`. `console_init()` prints the SMM header and we
want to append the verstage contents before printing the header to avoid
confusion.
BUG=b:221231786
TEST=Perform S0i3 cycles and verify PSP verstage logs now show up when
doing `cbmem -c`.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I64d33ccdee9863270cfbcaef5d7c614349bd895c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change provides hooks for the SoC so it can perform any
initialization and cleanup in the SMM handler.
For example, if we have a UART enabled firmware with DEBUG_SMI, the UART
controller could have been powered off by the OS. In this case we need
to power on the UART when entering SMM, and then power it off before we
exit. If the OS had the UART enabled when entering SMM, we should
snapshot the UART register state, and restore it on exit. Otherwise we
risk clearing some interrupt enable bits.
BUG=b:221231786, b:217968734
TEST=Build test guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I946619cd62a974a98c575a92943b43ea639fc329
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62500
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Sets GPIO 42 to high to turn off WWAN DPR
BUG=b:216735313
BRANCH=guybrush
TEST=emerge-guybrush coreboot
make sure GPIO42 is high
Change-Id: Id0fcf27f086f98b2d42b47c8a871252b52d204ba
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Enable PCIe support for mt8195.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: I314572955f1021abe9f2f0f4635670135ed08fff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Add a new function 'mtk_pcie_pre_init' to assert the PCIe reset at early
stage to reduce the impact of 100ms delay.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: If6799c53b03a33be91157ea088d829beb4272976
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Micron MT62F2G32D8DR-031 will be used for skyrim P1. Add it to the parts
list and regenerate the SPDs using spd_gen.
BUG=b:213926260
TEST=util/spd_tools/bin/spd_gen spd/lp5/memory_parts.json lp5
Change-Id: Iad2bb53de2b54648d5dd66808973f26b1c8a5df7
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62542
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Log the platform boot mode reported by PSP verstage to PSP stage 1
bootloader. This helps to improve the debuggability.
BUG=b:193050286
TEST=Build and Boot to OS in Nipperkin. Ensure that the platform boot
mode is logged in the verstage logs.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I752ee56f2af48215a770d799432d02f0609757cd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
GPIO_18 is used for LCD_PRIVACY_SCREEN feature starting board phase 2.
But it is programmed incorrectly in the concerned ACPI device. Pass the
correct GPIO.
BUG=b:204401306
TEST=Build and boot to OS in Nipperkin. Ensure that the ACPI object
contains the right GPIO. Ensure that the screen visibility gets updated
by pressing the privacy screen button.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I99d40b49f4e97063f1ec2e15ac3da21f700a93eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
As part of boot time optimization, one of the culprit was CSE where
response to End Of Post (EOP) command used to take ~60ms. Earlier patch
was pushed to delay the EOP to reduce response time to ~5-7 ms. During
this stage overall platform boot time was ~1.15 seconds.
Once boot time was optimized to ~ 1 seconds, CSE EOP time again
increased to ~80 ms since coreboot used to send EOP at the time where
CSE was busy. This created some back and forth moving of sending EOP
command function within coreboot sequence.
Upon debugging using traces, it was found that coreboot used to send
EOP late where CSE was busy loading other IP payload, so it might take
more time to respond.
In order to avoid delayed response, coreboot has to send EOP in
stage when CSE is done with firmware init and it will be ready to
serve EOP as soon as possible. This also aligns with previous flow where
FSP used to send EOP once silicon init is done and coreboot used to
rely on FSP to send this message.
Moving EOP to earlier stage (From SoC) meets the requirement and CSE EOP time
reduces from ~60 ms to ~20 ms on Brya board.
Note that once SoC code sends EOP, coreboot common code won't send it
again since common code already has check in case EOP is sent earlier.
BUG=b:211085685
BRANCH=firmware-brya-14505.B
TEST=Tested on Brya system before and after the changes. Observed ~40ms
savings in boot time.
Change-Id: I9401d5e36ad43cdc0dfe947aabc82528d824df9b
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Earlier while trying to optimize boot time End Of Post (EOP) time kept
increasing (~80 ms) when boot time decreased to around 1 second.
This was because CSE was busy with own firmware loading.
When EOP was moved later in boot stage it again created issue since CSE
got busy with other payload loading for OS boot, so response to EOP
got delayed by ~70-80 ms.
In order to avoid delayed response, coreboot has to send EOP in
stage when CSE is done with firmware init and it will be ready to
serve EOP as soon as possible. This also aligns with previous flow
where FSP used to send EOP once silicon init is done and coreboot used
to rely on FSP to send this message.
Moving EOP to BS_DEV_INIT boot state meets this requirement and CSE EOP
time reduces from ~60 ms to ~20 ms on Brya QS board.
Since this setting might vary for each SoC, SoCs can decide when to send
EOP in the boot sequence. This patch adds Kconfig option to send EOP via
SoC
BUG=b:211085685
BRANCH=firmware-brya-14505.B
TEST=Code compilation is fine for Brya board. Boot time test is done
using entire patchset and EOP time is reduced to ~25ms from earlier ~80ms.
Change-Id: I9c7fe6f8f3fadb68310d4a09692f51f82c737c35
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
The Brask DDR4 setting are interleave, due to Moli PCB layer limited and the routing need to smooth, we will use non-interleave for Moli DDR4.
BUG=b:219831754
Signed-off-by: zoey wu <zoey_wu@wistron.corp-partner.google.com>
Change-Id: Iab153f16a3b729e7fa9daaa3dbfbccc70e6d789d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Decrease PSysMax from 13.52 A to 11 A for Moli variant according to its power circuitry, implying Psys_Pmax = 11A * 19.5V = 214.5W
BUG=b:215258941
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: I61f4813f3527123a590d80b4a6e49d76ebb71c99
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Hook up vtd_enable to CMOS value of "vtd".
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I16b43f0489f652d650e820c36b2b9bea61cf3c8c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61679
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Don't return 0x00 when running MWAK as it is not needed.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ic62eab8ae5319aff37c61fc29d701d9a36ada919
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Use ECWR function, instead of writing raw values to emem, to avoid a
lack of syncronisation as it uses a mutex.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I90cfd3e1752fe25493bd72ea6bcab1fd9318d2e3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The current code will write the raw value from the CMOS, which doesn't
match the respective setting in EC.
Switch argument will write the correct value, and prevent the setting
being reset.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I40dc78c743f4201a11ea0c26a8af716cab42b805
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The current code will write the raw value from the CMOS, which doesn't
match the respective setting in EC.
Switch argument will write the correct value, and prevent the setting
being reset.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I93444cdb96eaf729630b48551d0853511b584634
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The current code will write the raw value from the CMOS, which doesn't
match the respective setting in EC.
Switch argument will write the correct value, and prevent the setting
being reset.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Iabeec47bf492b698f95d86aa2d08ba9caedd75f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The current code will read the raw value from the EC, which doesn't
match the respective setting in CMOS.
Switch argument will store the correct value.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ic2a83df9a270de6d7bab295e732a6c13accbe17c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62606
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The current code will read the raw value from the EC, which doesn't
match the respective setting in CMOS.
Switch argument will store the correct value.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I62e0fc3b6fcae72f2d8eacf37a390b4e4b1f0783
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62605
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The current code will read the raw value from the EC, which doesn't
match the respective setting in CMOS.
Switch argument will store the correct value.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I921be8aea55b95f1ba233d2640d9bae80f8c3703
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62604
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove the dependency on Arg0 so PTS always runs.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I96c44397d62848231039330a32de781f75bb56bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Andy Pont <andy.pont@sdcsystems.com>
This solved the error:
i801_smbus 0000:00:1f.1: can't derive routing for PCI INT A
i801_smbus 0000:00:1f.1: PCI INT A: not connected
i801_smbus 0000:00:1f.1: SPD Write Disable is set
i801_smbus 0000:00:1f.1: SMBus using polling
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Idebd581b7ed6d193d83340b7dc94248df43525c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The mainboard may not be able to disable the internal cap, so we want
to set 0xe0 for all boards to minimize the internal cap. And a
mainboard implementation may choose XTAL with higher cload if the
frequency requirement is met, and the total capacitance can be tuned
externally for different boards.
BUG=b:218439447
TEST=set capid to 0xe0.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I2139e6b3456d7a50e3cdc8fc606e5f6ea3406044
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62563
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Rename SPIROM_BASE_ADDRESS_REGISTER to SPI_BASE_ADDRESS_REGISTER to
clarify that this isn't the address the SPI flash gets mapped, but the
address of the SPI controller MMIO region. This also aligns the register
name with the PPR.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifd9f98bd01b1c7197b80d642a45657c97f708bcd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62578
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Some non-SoC code might want to know whether or not the CNVi DDR RFIM
feature is enabled. Also note that future SoCs may also support this
feature. To make the CnviDdrRfim property generic, move it from
soc/intel/alderlake to drivers/wifi/generic instead.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Idf9fba0a79d1f431269be5851b026ed966600160
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Varshit B Pandya <varshit.b.pandya@intel.com>
This is passing through a cb_err from cbfs_prog_stage_load(), so it
should be declared to return that as well.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I5510d05953fe8c0e2cb511f01f862b66ced154ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62656
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, all of the commands for building futility are printed as they
are run. This change skips printing the check for libcrypto unless the
check actually fails. This prevents the error from being displayed when
there isn't actually a problem.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I9ef36c0b64f7cd69d19b8faabd165ef6651c838e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
While running Sphinx, it shows the warning "document isn't included in
any toctree" for the documents checklist.md and templates.md. These are
not meant to be listed in ToC trees.
Thus, mark them as orphaned to exclude them from ToC trees.
Change-Id: I1ff8f7c24ac9b3c3a120914c0c72ab73e85c4873
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62584
Reviewed-by: Thomas Heijligen <src@posteo.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set NOR pin drive to 8mA to comply with HW requirement.
This implementation is according to chapter 5.1, 5.6 and 5.8 in MT8186
Functional Specification.
BUG=b:218775654, b:216462313, b:212375511
TEST=SPI SI tests for AP to NOR pass for both kingler and krabby.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I5b6e37b0f7d4207ea35f11394d25ad1e096ac01a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Felix Held