This change fixes the two sets of pins that were swapped in the
map of DQS signals from CPU to DRAM for channel 1.
Although this does not appear to have any impact to the system it
does result in different register values for DQS pin mapping that
are programmed inside FSP.
BUG=chrome-os-partner:58666
TEST=This fix was verified against the current schematic and using
FSP debug output.
Change-Id: I45b821071ba287493b3b13204b7f5b38e06eee75
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18279
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The selection of the SSC reference frequency for LVDS was based on a
completely unrelated clock.
The `ssc_freq` flag should be set when the SSC reference runs at a
different frequency than the general display reference clock (DREF).
For most platforms, there is no choice, i.e. for i945 and gm45 the SSC
reference always differs from the display reference clock (i945: 66Mhz
SSC vs. 48MHz DREF; gm45: 100MHz SSC vs. 96Mhz DREF), for Nehalem and
newer, it's the same frequency for SSC/non-SSC (120MHz). The only,
currently supported platform with a choice seems to be Pineview, where
the alternative is 100MHz vs. the default 96MHz.
Change-Id: I7791754bd366c9fe6832c32eccef4657ba5f309b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/18186
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
same change as I49935e659bf67225d3f5db1b06acc2cd046dcd74
this is required for poppy board as well.
GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals
when doing GPIO-driven I2S. This needs to be high by default so
the DSP can drive these signals, instead of low where it is enabled
for GPIO-driven I2S and the DSP cannot drive these signals.
BUG=None
BRANCH=None
TEST=play test sound in OS over internal speaker
Change-Id: I1695e9198f8f78e9c5ad6df6c1ac073ac1762c6b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18282
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals
when doing GPIO-driven I2S. This needs to be high by default so
the DSP can drive these signals, instead of low where it is enabled
for GPIO-driven I2S and the DSP cannot drive these signals.
BUG=chrome-os-partner:58666
TEST=play test sound in OS over internal speaker
Change-Id: I49935e659bf67225d3f5db1b06acc2cd046dcd74
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18281
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The me_cleaner option is available on multiple platforms:
* Sandy and Ivy Bridge (well tested by multiple users).
* Skylake and Braswell (tested).
* Haswell, Broadwell and Bay Trail (untested).
The untested platforms have been included anyways because all the
firmwares are very similar and Intel ME/TXE probably behaves in the
same way.
Change-Id: I46f461a1a7e058d57259f313142b00146f0196aa
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/18206
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add VFCT table to provide PCI Optiom Rom for
AMD graphic devices.
Useful for GNU Linux payloads and embedded dual GPU systems.
Tested on Lenovo T500 with AMD RV635 as secondary gpu.
Original Change-Id: I3b4a587c71e7165338cad3aca77ed5afa085a63c
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Change-Id: I4dc00005270240c048272b2e4f52ae46ba1c9422
Reviewed-on: https://review.coreboot.org/18192
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
With coreboot 4.4 switched to "Descriptor mode" for Lenovo T500
it automatically unlocks all flash regions. For Gbe region
the "Requester ID" was hardcoded resulting in *dead* Gbe.
Keep board specific "Requester ID" while unlocking Gbe region.
Allows Lenovo T500 to boot with IFD "Descriptor mode" with unlocked
flash regions.
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Change-Id: Ia4b5d1928e84bee42182fc83020e3a13fadc93c4
Reviewed-on: https://review.coreboot.org/18055
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This patch sets PL2 override value to 15W in RAPL registers.
BUG=chrome-os-partner:62110
BRANCH=reef
TEST=Apply new firmware to evaluate Octane benchmark score.
Change-Id: I51734051586753677129314b5273fb275c74f5d2
Signed-off-by: Harry Pan <harry.pan@intel.com>
Reviewed-on: https://review.coreboot.org/18283
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
This allows for defaults to be applied to CMOS parameters
when cmos checksum is incorrect.
This probably results in changed cmos settings for current users of
these targets.
Change-Id: Ifec0093f4b0dbaa51b96812a041f0eaf5c58ee86
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17041
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Activate the IOMMU for the ASUS F2A85-M LE board.
Enable the IOMMU in `devicetree.cb` and build AGESA IOMMU code by
enabling the option in `buildOpts.c`.
ACPI and MPTABLES interrupt routers are already present since they are
syminks to the F2A85-M version.
```
$ uname -a
Linux nukunuku 4.8.5 #35 SMP Sun Oct 30 19:34:55 CET 2016 x86_64 GNU/Linux
$ lspci -s 0.2
00:00.2 IOMMU: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) I/O Memory Management Unit
$ dmesg | grep -i IOMMU
ACPI: IVRS 0x00000000BFFAFF70 000070 (v02 AMD AMDIOMMU 00000001 AMD 00000000)
AMD-Vi: Applying erratum 746 workaround for IOMMU at 0000:00:00.2
iommu: Adding device 0000:00:01.0 to group 0
[...]
iommu: Adding device 0000:00:18.5 to group 9
iommu: Adding device 0000:03:00.0 to group 8
AMD-Vi: Found IOMMU at 0000:00:00.2 cap 0x40
AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
```
Change-Id: I6049fcfad53d16a99495d7a8fbc584c71e371d73
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/18259
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Adds checks for OpenBSD in all the places that were already checking for
NetBSD. This fixes e.g.:
ec.c:21:20: error: sys/io.h: No such file or directory
which was caused by defaulting to Linux.
Also, OpenBSD calls its amd64 iopl amd64_iopl instead of x86_64_iopl.
This change just defines iopl appropriately depending on the
OS and architecture.
TEST=Build on OpenBSD 6.0 or -current from 2017-01-25.
Change-Id: If6d92a9850c15cd9f8e287cc4f963d3ff881f72c
Signed-off-by: Steven Dee <i@wholezero.org>
Reviewed-on: https://review.coreboot.org/18260
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This mainboard is based on Intel's Leafhill CRB with Apollo Lake
silicon. In a first step, it concerns only a copy of intel/leafhill
directory with minimum changes. Special adaptations for MC APL1
mainboard will follow in separate commits.
Change-Id: If0b8a2bc21c99c3be4e6043e8febfb1b91ff0a63
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18272
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Brenton Dong <brenton.m.dong@intel.com>
Change depthcharge to not require a board-specific config file for
libpayload. If the Kconfig option is selected, use the settings
in libpayload/configs/defconfig instead.
Change-Id: I4fd1a5915472f28e757c62f3f2415716f1fdfc71
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/18271
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add new ChromeOS devices banjo, candy, clapper, glimmer, gnawty,
heli, kip, orco, quawks, squawks, sumo, swanky, and winky using
their common reference board (rambi) as a base.
Chromium sources used:
firmware-banjo-5216.334.B 32ec493 [chromeos: vboot_loader: Set...]
firmware-candy-5216.310.B 519ff11 [baytrail: Preserve VbNv around...]
firmware-clapper-5216.199.B 80d55e3 [baytrail: add code for...]
firmware-glimmer-5216.198.B fae0770 [baytrail: add code for...]
firmware-gnawty-5216.239.B 952adb7 [Gnawty/Olay: Add 2nd source...]
firmware-heli-5216.392.B f1f3604 [helis: Lock ME / TXE section...]
firmware-kip-5216.227.B db3c5d9 [kip: update spd for for MT41K256M16*]
firmware-orco-5216.362.B 76f1651 [Orco: Adjust rx delay for norm.]
firmware-quawks-5216.204.B edb60c9 [Quawks: Update SPD data]
firmware-squawks-5216.152.B c6573dc [Squawks: Update SPD data]
firmware-sumo-5216.382.B c62b6f23 [Ninja, Sumo: Add SPD source...]
firmware-swanky-5216.238.B 233b2a7 [Swanky: update SPD table]
firmware-winky-5216.265.B ce91ffc [Add to support HT Micron...]
The same basic cleanup/changes are made here as with the initial BYT
variant commit:
- remove unused ACPI trackpad/touchscreen devices
- correct I2C addresses in SMBIOS entries
- clean up comment formatting
- remove ACPI device for unused light sensor
- switch I2C ACPI devices from edge to level triggered interrupts,
for better compatibility/functionality (and to be consistent
with other recently-upstreamed ChromeOS devices)
- Micron 2GB SPD file for kip with updated values renamed to distinguish
from same file used by other boards
Change-Id: Ic66f9b539afb5aff32c4c1a8563f6612f5a2927c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18164
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add the capability for specifying which version of depthcharge to
checkout and build. This is similar to the existing feature for
SeaBIOS.
The depthcharge makefile already contains some structure for checking
out master vs. stable however the calling Makefile.inc ingored this
feature. Add the command-line variable assignment for these, along
with a tree-ish for any revision.
Change-Id: I99a5b088cb0ebb29e5d96a84217b3bfa852de8ac
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/18270
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Depending on the commit to build, depthcharge may have a different
target name (depthcharge vs. depthcharge_unified). Add some logic
to determine which name should be used based on the commit ID
being requested.
Change-Id: I05b853934d13696f4bd0d79d53ff6c5f59096d1c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/18269
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Drop the _unified moniker from the depthcharge build. The payload
and coreboot have drifted out of sync and there is no longer a
non-unified depthcharge.
This patch corresponds with the depthcharge change:
https://review.coreboot.org/cgit/depthcharge.git/commit/?id=74a0739
Change-Id: I8d028b14d2eee63dfdc9d3dd63695f1c58ea7984
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/18268
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
That status isn't needed and making it non-static helps gcc 4.9.2 (or
any compiler that insists on "standard C" behaviour with global const
initializers)
Change-Id: Ib1fbd5213d262e653f31564b106095b4a28292f6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/18266
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We rely on gnu make, so we can expect the jobserver to be around in
parallel builds, too. Avoids some make warnings and slightly speeds up
the build if those sub-makes are executed (eg for arm-trusted-firmware
and vboot).
Change-Id: I0e6a77f2813f7453d53e88e0214ad8c1b8689042
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/18263
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Speed up the execution of this script from ~6 seconds to ~1 on my
system.
There are some changes to its output, but they're actually _more_
correct: so far, architectures without compiler support kept compiler
options for architectures that ran successfully earlier.
Change-Id: I0532ea2178fbedb114a75cfd5ba39301e534e742
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/18262
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reorder the items to minimize the differences.
Change-Id: I745ec70a990f997d87c2a0b6164ae127eb694ddf
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/17438
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The rule to make spd.bin that's in src/lib is for the 'generic_spd_bin'
implementation. It wasn't guarded though, so it was generating a build
warning for any other platform that generated an spd.bin file.
Sample warning that this fixes:
src/mainboard/gizmosphere/gizmo/Makefile.inc:42:
warning: overriding recipe for target 'build/spd.bin'
src/lib/Makefile.inc:298: warning: ignoring old recipe for target
'build/spd.bin'
Change-Id: Iadd6743f8ae476969bf36f99b918f04c04172d1d
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/18261
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Apollolake boards should use DMIC-4ch configuration in Kernel side and
use CaptureChannelMap in userspace to distinguish boards with different
number of DMIC's. So, NHLT DMIC 1-ch & 2-ch endpoint configuration will
not be required and hence removed.
BUG=chrome-os-partner:60827
TEST=Verify internal mic capture
TEST='arecord -Dhw:0,3 dmic_4ch.wav -f S16_LE -r 48000 -c 4 -d 10' works
Change-Id: Ibe81290906c9e379ae49e437648ee9cd6f123ff8
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/18252
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
EC sets the logic level based on outstanding wake events. When GPIO_22
is configured as a level triggered interrupt, the events are not
cleared from the interrupt handler. Hence, we'd just be re-signalling
over and over causing an interrupt storm upon lid open. So, GPIO_22
needs to be configured as EDGE_SINGLE instead of LEVEL.
BUG=chrome-os-partner:62458
TEST=Lid close/open. check CPU usage using top. It should
not show 70% CPU usage.
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Change-Id: I710a690578c6e5b63be34b7fbcb21c703ef56e3a
Reviewed-on: https://review.coreboot.org/18267
Tested-by: build bot (Jenkins)
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
For the boards that intend to use mock tpm and have recovery mrc cache
support enabled, provide mock functions to read and write mrc hash
space.
Reading MRC hash space returns TPM_SUCCESS as later checks take care of
comparing the hash value and retraining if hash comparison fails. Thus,
in case of mock tpm, device would always end up doing the memory
retraining in recovery mode.
BUG=chrome-os-partner:62413
BRANCH=None
TEST=Verified that eve builds with mock tpm selected.
Change-Id: I7817cda7821fadeea0e887cb9860804256dabfd9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18248
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
1. For ELAN, export reset GPIO as well as PowerResource
2. For WCOM, export PowerResource
BUG=chrome-os-partner:62311, chrome-os-partner:60194,
chrome-os-partner:62371
BRANCH=reef
TEST=Verified that touchscreen works on pyro with WCOM device on
power-on as well as after suspend/resume.
Change-Id: I0306e24e19bf821cd3e08fdacc0d78b494c9a92f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18239
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Linux kernel expects that power management with ACPI should always be
handled using PowerResource. However, some kernel drivers (e.g. ELAN
touchscreen) check to see if reset gpio is passed in by the BIOS to
decide whether the device loses power in suspend. Thus, until the kernel
has a better way for drivers to query if device lost power in suspend,
we need to allow passing in of GPIOs via _CRS as well as exporting
PowerResource to control power to the device.
Update mainboards to export reset GPIO as well as PowerResource for
ELAN touchscreen device.
BUG=chrome-os-partner:62311,chrome-os-partner:60194
BRANCH=reef
TEST=Verified that touchscreen works on power-on as well as after
suspend-resume.
Change-Id: I3409689cf56bfddd321402ad5dda3fc8762e6bc6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18238
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This fixes the build for the generated code for boards with PS/2
keyboard, since commit 448e386309 updated the pc_keyboard_init()
function.
Change-Id: I776b49b847985296eaca4af6d6e49ab5d6abbafe
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/18242
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
I2C data (GPIO_132) and Clk (GPIO_133) lines are pulled low during
standby states S3/S0ix. This causes leakage of power. To reduce the
leakage, we have to pull these lines high during S3/S0ix. This is
done by programming the IOSSTATE to HIz. Also note that we are using
the internal pull ups to keep at SOC at 1.8V and the I2C lines are
not floating.
BUG=chrome-os-partner:62428,chrome-os-partner:61651
TEST=Enter S3/S0ix. Measure trackpad power. It should be less
than 4mW. Also I2c lines should be pulled high in S3/S0ix.
Change-Id: I5570ac37ec3cc41f6463dd6b858fdb56a20a1733
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/18251
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
The SeaBIOS and coreboot log levels don't really align, so setting the
SeaBIOS log level to the same as coreboot's isn't really what we want.
- Update default log level to use the default SeaBIOS log level.
- Update the current help text to match the new defaults.
- Add help text for what is displayed at various levels.
- Get rid of separate type & prompt lines.
- Add comments for default seabios level & logging disabled
Change-Id: I5a8b75bd44748cb94a83a77ac3a379c8a9587e7b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18210
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kevin O'Connor <kevin@koconnor.net>
Currently coreboot runs the 'config' command if no .config file exists.
This isn't what anyone wants, and is particularly frustrating for tools
that automate the build, where the build just hangs waiting for input.
Instead, just show an error message and then exit the build.
Change-Id: If9e0c2c26f8273814518589a2f94c5b00fc4cefe
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18245
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Intel Core 2 is not further specified since not all chipsets support
quad cores, which could confuse users.
Change-Id: I86c0a41743fe784f432347fa639d3c26604e058e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18235
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
- Use dashes instead of underscores for consistency and to match other
coreboot targets
- Fix a couple of places where old target names were referenced
- Remove double 'help' target from .PHONEY target list
Change-Id: I3b464ebf74653a8cc880e982316fd883757ec728
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/18000
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Kill running docker containers before trying to remove images or
containers.
Change-Id: Id2de90edbe5d0dc6ecb906be7101ad9744dbd11e
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/17999
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
- Fix TODO: restrict $1 to allowed values.
- Specifically exclude 'oem' board status directories.
- Exclude any directory that doesn't follow the date format to keep
the script from breaking again in the future if something it doesn't
recognize is pushed. Just ignore it for the wiki.
- Fix shellcheck warnings.
Change-Id: I2864f09f5f1b1f5ec626d06e4849830400ef5814
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18225
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Without this motherboards that requires a non zero timeout for ps2
keyboards on SeaBIOS don't build when CONFIG_UPDATE_IMAGE is set.
An alternative way to achieve this file would be to include a cbfsfile
instead of calling cbfstool. That way the file gets updated/added both
both image update and regular build. A difficulty of that approach is
that it needs to convert a decimal to a binary in little endian
representation, which is not a trivial thing to do in a Makefile.
Change-Id: Icafba8d3e279a2e70e607abba81e3dbebfb55e4b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18231
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
If cmos is invalid, it doesn't make sense to read the value before
finding that out.
Change-Id: Ieb4661aad7e4d640772325c3c6b184de1947edc3
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18236
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Wacom touchscreen is i2c hid device and it's the device that always
exists.
So no need to set "probed" property for it.
BUG=chrome-os-partner:61513
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: I27fe18ceadd03029b826e0237f80132eda1089b0
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18227
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The default macaddress in rt8168.c can be changed with a cbfsfile
called macaddress. This patch makes it possible to add such a file
using Kconfig at build time.
This also changes the name of the cbfsfile from "macaddress" to
"rt8168-macaddress" to avoid confusion.
Change-Id: I24674d8df11845167b837b79344427ce0c67f4fb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18088
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Ubuntu’s default compiler flags for GCC [1][2] include `-Wformat
-Wformat-security`, causing errors similar like the one below.
```
CC romstage/northbridge/amd/amdht/ht_wrapper.o
src/northbridge/amd/amdht/ht_wrapper.c: In function 'AMD_CB_EventNotify':
src/northbridge/amd/amdht/ht_wrapper.c:124:4: error: format not a string literal and no format arguments [-Werror=format-security]
printk(log_level, event_class_string_decodes[evtClass]);
^
[…]
```
Fix that, by explicitly using a format string.
TEST=Built and booted on ASUS KGPE-D16.
[1] https://stackoverflow.com/questions/17260409/fprintf-error-format-not-a-string-literal-and-no-format-arguments-werror-for
"fprintf, error: format not a string literal and no format arguments [-Werror=format-security"
[2] I tested with gcc (Ubuntu 5.4.0-6ubuntu1~16.04.4) 5.4.0 20160609.
Change-Id: Iabe60deeffa441146eab31dac4416846ce95c32a
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/18208
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
me_cleaner is a tool to strip down Intel ME/TXE images by removing all
the non-fundamental code, while keeping the ME/TXE image valid and
suitable for booting the system. The remaining code (ROMP and BUP
modules) is the one responsible for the very basic initialization of
the ME/TXE subsystem and can't be removed.
This tool exploits the fact that:
* Each ME/TXE partition is signed individually and it is possible to
remove both the partition and the signature.
* The ME/TXE modules are not signed directly, instead they are hashed
and the list of their hashes is hashed again and signed: this
means that modifying a module doesn't invalidate the signature,
but only the hash of that single module.
* The modules hashes are checked only when the corresponding module
needs to be executed.
* The system can boot after the execution of the first module (BUP,
inside the FTPR partition), even if the subsequent stages fail.
Currently me_cleaner works on every Intel platform with Intel ME or
Intel TXE with the following limitations:
* Doesn't work when Intel Boot Guard is set in Verified Boot mode.
* Doesn't fully work on Nehalem yet.
* On Skylake and later generations, since the partitions' internal
structure has changed, me_cleaner leaves intact the FTPR
partition, removing all the the other partitions.
This tool has been tested on multiple platforms and architectures by
different users, and seems to be stable. The reports are available
here:
https://github.com/corna/me_cleaner/issues/3
A more in-depth description of me_cleaner is available here:
https://github.com/corna/me_cleaner/wiki/How-does-it-work%3F
Change-Id: I9013799e9adea0dea0775b9afe718de5fc4ca748
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/18203
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When .xcompile doesn't already exist, building libpayload fails because
the CC variable (et al) remain empty since .xcompile is only included
after the variables coming from there are evaluated.
Change-Id: I73f1cbced95afcff15839604fea5fd05d81bc3d3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18228
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Make the code C89 compatible, which doesn’t allow loop initial
declarations. Older compilers use C89 by default, so just declare the
variable outside.
Change-Id: I3c5a8109e66f7a25687f4e4b2c72718d74276e04
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/18196
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This fixes building coreboot with -std=gnu11 on gcc 4.9.x
Also needs fix ups for asus/kcma-d8 and asus/kgpe-d16 due to the missing
type.
Change-Id: I920d492a1422433d7d4b4659b27f5a22914bc438
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18220
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Duncan Laurie