Move the check for NOCOMPILE flag around the whole block. There's
no need to test COMPILERFAIL if NOCOMPILE is set.
Comment the endif lines to make it easier to understand.
Signed-off-by: Martin Roth <martinroth@google.com>
Change-Id: Id7bb5ca13e6bf1cabf4b7b2ff3256b47b966bac1
Reviewed-on: https://review.coreboot.org/12678
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Change-Id: I45ed5e289f9bfae90d71938243f921588b256e39
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12676
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
When coreboot is pulled in as a submodule, the .git "folder" is a file,
not a folder. Use the '-e' test instead of '-d' to allow for that.
Change-Id: I0dd8866b0016f7ba099cdaf4d7db442ff22612b5
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Reviewed-on: https://review.coreboot.org/12819
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This reverts commit d3deecdd9c.
Do not mix open-source AGESA and binary PI trees. Once you have
working S3 support for binaryPI platforms, add the adapted
oem_s3.c file as northbridge/amd/pi/oem_s3.c instead.
Change-Id: I7c981d0023a5c0225e046f9c0104acfa07436b79
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/12282
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Make the low-power and small form factor (SFF) options overridable
from romstage main. Also disable both options by default. That's ok
as there aren't yet any in-tree users of the GS45 chipset. As a nice
side-effect, this adds X200s support to the lenovo/x200 port.
Change-Id: I94373851262e6d424cf4885ceca7260c31bc9f61
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/12814
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
All southbridge interrupt pin and routing registers (D*IP and D*IR)
are left at their default values (see ICH9 datasheet) and this file
just has to reflect them.
Change-Id: I687262556d918311757fda9afda9ebfdd7edf947
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/12813
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Set up External Temperature to read via thermal diode/resistor
into TMPINx register by setting thermal_mode switch.
Original-Signed-off-by: Ted Kuo <tedkuo@ami.com.tw>
Change-Id: I0e8621b92faa5c6246e009d2f852c8d4db484034
Original-Reviewed-on: https://chromium-review.googlesource.com/260545
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Original-Tested-by: Ted Kuo <tedkuo@ami.com.tw>
Original-(cherry picked from commit 973e2d393f2595b756f8aa20f6fbe3b6e045621a)
Original-Reviewed-on: https://chromium-review.googlesource.com/262340
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/12798
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The RPU Clock register defaults to on for all clocks.
This is modified to OFF, and the MIPS clock control modified to ON,
by default. This is because the linux kernel will manage the
clocks at all times, but the RPU can only disable clocks if the WIFI
module has been loaded.
Change-Id: I155fb37afd585ca3436a77b97c99ca6e582cbb4f
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: https://review.coreboot.org/12773
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
GRAM is 421056 bytes. The end of the SRAM region (GRAM plays the role
of SRAM) was placed at a 4K aligned address, resulting in a size of
408KB.
Change-Id: I9fa32ab818d600e7447bcac895e4b8c438f2f99d
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: https://review.coreboot.org/12772
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The base address for the I2C dividers (DIV1 and CLOCKOUT)
was erroneously set to the toplevel clock controller base
address and not to the correct peripherals clock controller
base address.
Change-Id: I66bbc1e741bcf6251babee7ddd6376d49d7cb3d1
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: https://review.coreboot.org/12771
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This region must be mapped uncached. This is necesary for an
U-boot payload which will obtain all register base addresses
as physical addresses from the device tree and will use them
as such.
Change-Id: Ib5041df7d90c6ef61b7448a18dd732afbd9489ca
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: https://review.coreboot.org/12770
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When used with a U-boot payload it will need this region
identity mapped also, so we're defining it in preparation
for that functionality.
Change-Id: I27cee5b58cb899433b52bd06df07b5f2105212af
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: https://review.coreboot.org/12768
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Use SYS PLL in integer mode by default to reduce jitter.
DSMPD_MASK is defined and can be used to switch to fractional mode.
Tested on pistachio bring up board.
Change-Id: Ie6d2aca71c7af86b0993c804329e6d03e26ff754
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: https://review.coreboot.org/12767
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Board uses x4x native raminit
Board boots into Debian 8 with full graphics
IRQ9: nobody cared, gets disabled
(PIC needs IRQ settings?)
VGA:
- VGA native init works in grub with analog connector
- Fails to boot with both channels of ram populated
Change-Id: I7417813456817529b8cbaace45cefe47467d0a82
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/11306
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Passes memtest86+ with either one or two sticks of 2GB ram
but memory map needs a hole at 0xa0000000 to 0xc0000000
Change-Id: Ib34d862cb48b49c054a505fffcba1c17aeb39436
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/11307
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This code looks like it was created from a disassembly of some
other driver. Attempt to fix it, without hardware or documentation.
CID 142909: Operands don't affect result (CONSTANT_EXPRESSION_RESULT)
Change-Id: I9b9cadf2acdba73913aad6bbe0d14ad64a652915
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/12774
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
The FMD is board-specific, so it makes sense to have it in the
mainboard menu.
Change-Id: I52fba5ced869d51d10065f8c9ebd258d3a1d4156
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/12805
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
After several internal discussions, teams at Intel with stakes in
coreboot have decided to each assign one or more maintainers. These
maintainers can be expected to provide a point of contact for
assistance with technical (code-related) issues, testing on real
hardware, and making sure that their FSP-related areas continue to
function with upstream coreboot.
They understand that the inclusion of their information in the
MAINTAINERS file does not give them any extra power over their areas.
At the same time, nobody expects any community process to change.
The one expectation is that reasonable efforts be made to contact
these maintainers when making fundamental changes to their areas, or
when discussing code removal.
Change-Id: I62b2eaec8270ac1fce5bfbee3b3da68aba116b0f
Signed-off-by: Alexandru Gagniuc <alexandrux.gagniuc@intel.com>
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/11894
Reviewed-by: York Yang <york.yang@intel.com>
Tested-by: build bot (Jenkins)
Non-code flow assembly stubs do not have to be included in
bootblock.S, now that we have more freedom in bootblock linking.
Rather than bringing these stubs to the config system, just link them
in the bootblock.
Note that we cannot fully remove CHIPSET_BOOTBLOCK_INCLUDE at this
point, as some intel SOCs use this stub for code flow.
objdump -h build/cbfs/fallback/bootblock.debug on a few random boards
confirms that the appropriate sections are still included in the
final binary.
Change-Id: Id3f9ece14e399c1cc83090f407780c4a05a076f0
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: https://review.coreboot.org/11856
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
- make sure CONFIG_CBFS_SIZE is lowercase for fmaptool.
- Regenerate the fmap.fmd file when config.h changes.
- Print the fmaptool step when doing the build.
Change-Id: Ib518ed469d9e39eb41c81f7b19480c7789067d2d
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/12806
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Since the introduction of the new (interim?) master header, coreboot
searches the whole ROM for CBFS entries. Fix that by aligning it on top
of the ROM.
Change-Id: I080cd4b746169a36462a49baff5e114b1f6f224a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/12810
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
After several internal discussions, teams at Intel with stakes in
coreboot have decided to each assign one or more maintainers. These
maintainers can be expected to provide a point of contact for
assistance with technical (code-related) issues, testing on real
hardware, and making sure that their FSP-related areas continue to
function with upstream coreboot.
They understand that the inclusion of their information in the
MAINTAINERS file does not give them any extra power over their areas.
At the same time, nobody expects any community process to change.
The one expectation is that reasonable efforts be made to contact
these maintainers when making fundamental changes to their areas, or
when discussing code removal.
Change-Id: I33d95db12d9e394360a207c8fbcfbc15723115c6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12642
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: York Yang <york.yang@intel.com>
According to the PNP ISA v1.0a spec, config registers in the range of
0xf0 up to 0xfe are vendor defined and may be used for any purpose.
Config register 0xff is reserved and is defined as such.
Currently, only vendor specific registers 0xf0, 0xf1, 0xf4, and 0xfa
are able to be set using the PNP_MSCx bit flag masks.
This patch adds support for all 15 vendor specific config registers,
and updates the existing superio pnp_info to use them where appropriate.
Change-Id: Id43b85f74e3192b17dbd7e54c4c6136a2e59ad55
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/12808
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Boots to console on Gigabyte GA-G41M-ES2L
Ram initialization *not* included in this patch
VGA native init works on analog connector
Change-Id: I5262f73fd03d5e5c12e9f11d027bdfbbf0ddde82
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/11305
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
In order for a U-boot payload to work properly the soc_registers
region (device registers) needs to be mapped as uncached.
Therefore, add a coherency argument to the identity mapping funcion
which will establish the type of mapping.
Change-Id: I26fc546378acda4f4f8f4757fbc0adb03ac7db9f
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: https://review.coreboot.org/12769
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Using origin/master as the git revision breaks reproducibility, giving
different values depending on when the code was pulled from the
repo at coreboot.org. By using the current revision instead, we get
identical builds.
Change-Id: If4be6e048d6c8e417b8c074199745900ccd82b49
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12807
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This requires changes the interface that sets up the system
PLL to support a given reference devider value and given
feedback value.
Also, this requires a change in the dividers used for UART,
USB, I2C setup.
Change-Id: I98cf7c655dbb3e95b8fcee3c7f468122021c70b5
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: https://review.coreboot.org/12765
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The EHCI debug device setup code was removed from broadwell in
commit 49ee5ef: http://review.coreboot.org/11874
However the generic device setup code is in the southbridge/common/intel
directory while broadwell is in the soc directory so this is not used.
Add it back to the broadwell soc to fix undefined reference compile
errors with 'pci_ehci_dbg_dev' and 'pci_ehci_dbg_enable'.
This was tested to compile and produce romstage and ramstage output on a
google/samus board.
Change-Id: Ia93825a1e21a770f6c82d0989cb97980a5c700d6
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/12794
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The port0 and port1 registers were swapped, which meant it did
not work to apply the DTLE settings to the correct SATA port.
This was tested on an unreleased mainboard but is verified with
the documentation to be the correct register addresses now.
Change-Id: Ifb8890a563a741129ec8ddf72e73ab021c7d33da
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/12793
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Locking down the SPI controller with a specific opcode menu kills
the SPI console. Skip this when the SPI console config option is
enabled.
This was tested using an em100 and google/samus board to ensure
the console output does not stop at the finalize step.
Change-Id: Ie460f583214b47544e92d4afa8ef862563a11e36
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/12792
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Upcoming versions of IASL give a warning about unused methods. This
adds an operation after the read to use the local variable and avoid
the warning.
The warning can be completely disabled on the command line, but as it
can find real issues, my preference is to not do that.
Fixes warnings:
dsdt.aml 640: Store (CTMP, Local0)
Warning 3144 - Method Local is set but never used ^ (Local0)
Change-Id: If55bb8e03abb8861e1f2f08a8bcb1be8c9783afe
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12704
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Remove it8772f c includes
- Add a new LED API, it8772f_gpio_led
- Stumpy: using it8772f_gpio_led
BUG=chrome-os-partner:28232
BRANCH=Guado
TEST=emerge-guado coreboot chromeos-bootimage
Change-Id: I08de52515d3c1e7e85d1761c09a0cebffda7dda3
Signed-off-by: David Wu <David_Wu@quantatw.com>
Reviewed-on: https://chromium-review.googlesource.com/241813
Tested-by: David Wu <david_wu@quantatw.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Commit-Queue: David Wu <david_wu@quantatw.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/12797
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Looking at the A10 datasheet, N should go in bits 2:0, but
was being cleared by shifting it left by three bits, then
anding it with 7.
Fixes coverity warning:
CID 1241888 (#1 of 1): Wrong operator used (CONSTANT_EXPRESSION_RESULT)
operator_confusion: (n << 3) & (7U /* 7 << 0 */) is always 0 regardless
of the values of its operands. This occurs as the bitwise second operand
of '|'.
Change-Id: I17e71a73adf37a62607e8e5865b1da749d7278aa
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12779
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Baytrail has I2c Busses 0 to 6, so is supposed to error out
if the I2c driver is called with 7 or greater. Due to an off-by-one
error it could be called with bus 7.
Fixes coverity warning:
CID 1287074 (#1 of 1): Out-of-bounds read (OVERRUN)
3. overrun-local: Overrunning array base_adr of 7 4-byte elements at
element index 7 (byte offset 28) using index bus (which evaluates to 7).
Change-Id: I7caec60298cf27bd669796e0e05e4a896f92befd
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12781
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
- Also update post code comment to keep under 80 characters.
Change-Id: Id0fd0ee5660f2628fe33188855bebb6e3eea8d2e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12780
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Bit 8 of the MR register is automatically set by the PHY
during memory initilization but having it set in the
register leads to a more clear understanding.
Tested on Pistachio bring up board; DDR2 and DDR3 are
initialized properly.
Change-Id: Ie6953e2a96ba2961521b372d280f362ee1c52b94
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: https://review.coreboot.org/12764
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Switching on DQS Gate Early and DQS Gate Extension with
500R DQS/DSQN Resistors. This setup was recommended by
Synopsys.
Tested on Pistachio bring up board; DDR2 and DDR3 are
initialized properly.
Change-Id: I6cd3888d506effe71f5d535367525af2e51f6ba3
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: https://review.coreboot.org/12763
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
clang version now returns:
coreboot toolchain v1.33 November 25th, 2015 clang version 3.6.1
(tags/RELEASE_361/final) (based on LLVM 3.6.1)
Change-Id: I948d7f4d06c244987342cfc7d5c7e728cbed93bd
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12777
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These files need to be added to cbfs-files after PAYLOAD_CONFIG
and PAYLOAD_VERSION have been defined. Where they were before,
they didn't get added to the final build.
Change-Id: Ib1b230f9eb72a8c1710ef473a9f24c0fb7ec6e17
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12751
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
root_port_init_config() pcie.c wasn't initializing a variable before
passing its pointer to pch_iobp_exec(). pch_iobp_exec() wrote the
uninitialized value into a register.
In theory, the register would only be used if data was being written,
and pch_iobp_exec() was being used to read the data, not write it, so
this change shouldn't have any practical effect.
Fixes coverity error:
CID 1293134 (#1 of 1): Uninitialized scalar variable (UNINIT)
Change-Id: I5d17863d904c6b1ceb30d72b94cd7a40c8fbb437
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12778
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@google.com>
Quoting variables prevents word splitting and glob expansion, and
prevents the script from breaking when input contains spaces, line
feeds, glob characters and such.
See shellcheck warning SC2086.
Change-Id: I7256d2fc2a22bce7723950a534fef6d57cbd097f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12761
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This allows users who build the rom from the board-status repo to
verify that their rom matches the original.
Change-Id: I4e8564e389495909219f92ccdafb8e9568f8f0d0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12760
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Print what the script is doing so when it asks for the ssh password
several times in a row, it's obvious that it's actually doing different
things, not that the password failed.
- Don't print the output from cbfstool - it's not useful.
Change-Id: I785283475e14f242117682800c26db6b4f9f1e2c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12759
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If the payload_config and payload_version files are in coreboot.rom,
extract and save them.
Change-Id: I36b17ed189f94e2d4e873b0e219e5a9a2abe77a1
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12758
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The old serial port read method lost characters from the boot log. This
method works better for me.
- Put get_serial_bootlog arguments into variable names for clarity.
- Fully configure the serial port with stty: disable parity and flow control.
- Change serial port read from reading with 'cat' to reading with 'read'.
- Update help to show current default speed from the variable.
tested under dash, bash, and zsh on several platfoms.
Change-Id: I91ae63a3c226e61019dbdf69c405c3f20ba7db54
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12757
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Martin Roth