Initialize the base addresses for:
* Power management control
* Power management status
* Reset
* Power management timer
* General-Purpose Event 0
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file:
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the pdat.bin files in the location specified by
CONFIG_FSP_PDAT_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Build EDK2 CorebootPayloadPkg/CorebootPayloadPkgIa32.dsc to generate
UEFIPAYLOAD.fd
* Edit .config file and add the following lines:
* CONFIG_PAYLOAD_ELF=y
* CONFIG_PAYLOAD_FILE="path to UEFIPAYLOAD.fd"
* Testing successful when:
* Register address are properly displayed by the payload
* "reset -c" performs a reset and reboots the system
* "reset -w" performs a reset and reboots the system
* "reset -s" performs a reset and turns off the power
Change-Id: I9d043f4906a067b2477650140210cfae4a7f8b79
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/13764
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Enable HSUART1 for debug serial output. Specify the fixed resources in
the UART driver. This keeps debug serial output flowing during the rest
of the device initialization.
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the pdat.bin files in the location specified by
CONFIG_FSP_PDAT_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Testing successful if:
* Debug serial output stays enabled after BS_DEV_RESOURCES state
Change-Id: Ica02e5fece156b21d4a3889284ca467d55c7880d
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/13730
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add ramstage.h to define some of the common header files used by the
drivers in ramstage.
Add northcluster.c, the driver for the memory controller, which defines
the memory map.
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the pdat.bin files in the location specified by
CONFIG_FSP_PDAT_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Testing successful if:
* Memory map successfully displayed in BS_WRITE_TABLES state
Change-Id: I8dc91119eaad0b7abc2e484d13ee708ba1253438
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/13721
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Optionally relocate FSP into DRAM and then call FSP SiliconInit.
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Add "select DISPLAY_FSP_ENTRY_POINTS"
* Add "select DISPLAY_HOBS"
* Optionally add "select RELOCATE_FSP_INTO_DRAM"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the pdat.bin files in the location specified by
CONFIG_FSP_PDAT_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Testing is successful if:
* FSP entry points are displayed and
* The message "FspSiliconInit returned 0x00000000" is displayed and
* The HOBs are displayed correctly and
* The message "ERROR - Missing one or more required FSP HOBs!" is
not displayed
Change-Id: I91e660ea373a8bb00fc97fe8b760347cbfa96b1e
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/13631
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add the code to enable debug serial output using HSUART1:
* Enable the code using Kconfig value ENABLE_BUILTIN_HSUART1
* Note that the BIST value is always zero as validated in
esram_init.inc
* The initial TSC value is currently not saved!
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the pdat.bin files in the location specified by
CONFIG_FSP_PDAT_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Testing is successful if serial output is present on HSUART1 at
115200 baud, 8-bit, no parity
Change-Id: I7e6181e8b9bc901c3ab236f0b56534850bb6bfd0
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/13445
Tested-by: build bot (Jenkins)
Reviewed-by: FEI WANG <wangfei.jimei@gmail.com>
Successfully invoke TempRamInit from the FSP binary:
* Don't relocate the FSP binary image
* Copy the FSP binary into ESRAM
* Specify Kconfig values to easily debug ESRAM and TempRamInit code
* Specify the FSP binary file location
* Specify the FSP binary image ID
* Specify where in the flash image the FSP image must reside
* Specify the FSP data file location
* Specify where to place the FSP data file in the flash image
* Specify where in the ESRAM the FSP image must reside
Test 1 on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Add "select ENABLE_DEBUG_LED_FINDFSP"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Testing is successful if the SD LED is on indicating that the FSP.bin
file was properly located, The test fails if the SD LED is flashing.
Test 2 on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file
* Remove "select ENABLE_DEBUG_LED_FINDFSP"
* Add "select ENABLE_DEBUG_LED_TEMPRAMINIT"
* Testing is successful if the SD LED is on indicating that the FSP.bin
file was properly located, The test fails if the SD LED is flashing.
Change-Id: I1e2e413a8573f750c611b0f9df101b2c869a789e
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/13443
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
The Quark SoC uses ESRAM instead of cache-as-RAM. This code requires
that utils/xcompile/xcompile change the machine architecture from i686
to i586 to ensure that the Quark does not attempt to execute unsupported
instructions:
* Adjust Makefile.inc to add the RMU to the coreboot image
* Add code to enable the ESRAM
Directly use the QuarkSocPkg/QuarkNorthCluster/Include/QuarkNcSocId.h
file from the EDK2 tree (https://github.com/tianocore/edk2.git) to
enable
easy differences and correct issues in coreboot that were found in EDK2.
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file
* Add "select ADD_RMU_FILE"
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Remove power from the board
* Apply power to the board
* Testing is successful if the SD LED is on indicating that the end of
esram_init.inc was reached
Change-Id: I91d919da144bb72a5d4c4a8050ffab256632a395
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/13440
Tested-by: build bot (Jenkins)
Reviewed-by: FEI WANG <wangfei.jimei@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
