The macro definitions depend on __SIMPLE_DEVICE__ and are only used in
the get_gpio_base() or lpc_get_pmbase() functions, which already guard
PCH_LPC_DEV usage using __SIMPLE_DEVICE__ in preprocessor.
Change-Id: I5d3681debe29471dfa143ba100eb9060f6364c93
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Rename `BOARD_CLEVO_L140CU_OPTIONS` to `BOARD_CLEVO_L140CU_BASE` to
make clear that this option represents the baseboard.
Change-Id: I76690626fddafc8e3c37ef760aeb4f064fb6b591
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52480
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Memory init config is board specific. Thus, move it to variant level and
hook up variant romstage.c.
Change-Id: Id78788815ad9c4ed64f0172fb746ff6e50d608ef
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Hook up FSP-M configuration on mainboard level instead of variant level
being able to do common configuration there.
Also, hook up variant romstage.c on mainboard level for variant
specific configurations.
Change-Id: Ic161f83cb629b1e70ca670e10975a25bc0949656
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Add a new configuration low_power_probe to avoid camera privacy LED
blink during the boot.
Change-Id: I27d5c66fb380ae6cd76d04ee82b7736407dac1b0
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52189
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PARALLEL_MP_AP_WORK is set in the xeon_sp Kconfig. No need to
set it here.
Change-Id: I66d59fd7cbc3617eb739fdf2f3750f20ee701fbd
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Use the same stack location during relocation as for the permanent
handler.
When the number of CPUs is too large the stacks during relocation
don't fit inside the default SMRAM segment at 0x30000. Currently the
code would just let the CPU stack base grow downwards outside of the
default SMM segment which would corrupt lower memory if S3 is
implemented.
Also update the comment on smm_module_setup_stub().
Change-Id: I6a0a890e8b1c2408301564c22772032cfee4d296
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This reverts commit ad7c33abd2. With EFS2
already enabled in EC, enabling early EC sync is not required. Also a
workaround has been added in payload to address any boot issues.
BUG=b:185277224
TEST=Build and boot to OS in Guybrush in both normal and recovery mode.
Cq-Depend: chromium:2832032
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I34f8433739754365c8e5a10fdf7e58e3d1e7e797
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52419
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 1e36dc078e. With EFS2
already enabled in EC, enabling early EC sync is not required. Also a
workaround has been added in payload to address any boot issues.
BUG=b:185277224
TEST=Build and boot to OS in Guybrush in both normal and recovery mode.
Cq-Depend: chromium:2832032
Change-Id: I921dc5c814e5187dce283eeff43075b59885723a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52418
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If we select scancode set #1 and keep that, it can confuse Linux
with keyboards that don't return to set #2 when asked to load the
defaults. This happens for instance with various integrated Think-
Pad keyboards but was also seen with an external PS/2 one.
The chosen configuration, scancode set #2 without translation, seems
to be the default for many systems. So we can expect other payloads
and kernels to work with it.
Change-Id: I28d74590e9f04d32bb2bbd461b67f15014f927ec
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47594
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Instead of ignoring keyboards indefinitely when they failed to
initialize, we wait 5s and then start over with the hotplug
detection. As we always assume a present keyboard at first,
we'd otherwise never have a chance to hot plug a device after
the initial 30s timer ran out.
Change-Id: I8dec4921b2e932442d52b5118cdcf27090633498
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
While we assume a keyboard is attached, we send an echo command every
500ms. If there is no data coming from the keyboard within 200ms, we
assume it was detached.
Correspondingly, if we assume no keyboard is attached, we run an echo
command once per second.
Change-Id: I2c75182761729bf30711305f3d8b9d43eafad675
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47593
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Ensure the ChromeOS FMAPs are used only when CONFIG_CHROMEOS
is selected, so non-ChromeOS targets use the default x86 FMAP.
Change-Id: Id5d3e7a44973f2fadba3ea15e0e544eee7fa53e6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
EN_SPKR is routed to SD pin in the ALC1019 speaker amplifier. The
concerned pin has a voltage rating of 1.8V whereas the EN_SPKR GPIO has
a voltage rating of 3.3 V. The schematics has been updated to bridge the
gap. So enable the speaker amplifier by default and add a gpio override
table to disable the speakers before board version 2.
Also update the codec ACPI HID name for the kernel machine driver to
probe the codec successfully.
BUG=b:182960979
TEST=Build and boot to OS in guybrush. Ensure that the GPIO output state
is high.
Change-Id: I32b29bfae9bc94b5119b33a535d8bc825ef89445
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52355
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable AMD I2S machine driver and configure the devicetree with HID
information so that the machine driver ACPI objects can be passed to the
kernel.
BUG=b:182960979
TEST=Build and boot to OS in guybrush. Ensure that the ACPI objects for
machine driver is populated.
Change-Id: I8ed474d25273082d1e0742ba93746d97930deb19
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The selector component in Sound Open Firmware (SOF) can consume all the
mics and use the configuration in the Use Case Manager (UCM) to select
the right channel. Hence dmic select gpio configuration is optional.
BUG=b:182960979
TEST=Build and boot to OS in Guybrush. Ensure that the machine driver
ACPI object is populated without DMIC select GPIO.
Change-Id: Iba00b07c3656c487e33bab184fefee7037745e2d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52393
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ACPI_BERT_SIZE is used in the FSP driver and the fsp_m_params.c. The
latter one is planned to be deprecated though.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id1a250defbd31e255df9b7a7dd8488dc3182649b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
CB:31250 ("soc/intel/cannonlake: Configure GPIOs again after FSP-S is
done") introduced a workaround in coreboot for `soc/intel/cannonlake`
platforms to save and restore GPIO configuration performed by
mainboard across call to FSP Silicon Init (FSP-S). This workaround was
required because FSP-S was configuring GPIOs differently than
mainboard resulting in boot and runtime issues because of
misconfigured GPIOs.
This issue has since been fixed in FSP (verified with FSP v1263 on
hatch). However, there were still 4 boards in coreboot using
`cnl_configure_pads()`. As part of RFC CB:50829, librem_cnl, clevo/cml-u
and system76/lemp9 were tested to ensure that this workaround is no
longer required.
This change drops the workaround using `cnl_configure_pads()` and
updates all mainboards to use `gpio_configure_pads()` instead.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Tested-by: Angel Pons <th3fanbus@gmail.com>
(Tested purism/librem_cnl)
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
(Tested clevo/cml-u which is similar to system76/lemp9)
Change-Id: I7a4facbf23fc81707cb111859600e641fde34fc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52248
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update GPIO config based on review of latest schematics:
- LAN/WLAN reset lines are NC
- SDIO lines configured via GPP_G0-G7
- DMIC lines are wired directly to codec, not PCH, so GPP_D17-20
are set to NC
- Pads GPP_H0-H3 are configured for I2S2
- Pads GPP_H7-H9 are straps for board revision, so treated as GPI
- CPU_C10_GATE# is NC
- PWRBTN# does not need an internal pull-up
- GPP_C20-23 are configured for M.2 UART
- SATAXPCIE1/2 and EC SCI/SMI lines do not need internal pull ups
- GPP_C6/C7 set to I2C1 for future use
- GPP_E15 changed from SCI to SMI, edge triggered
Change-Id: If113cfeadf093e10dd84ab827ead594088f02ba1
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52389
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When a pad is configured as NC, it is set as a GPI with both
TX and RX disabled, and as the pad is internally disconnected,
no pull up or pull down is needed.
Change-Id: Id551b8f6f5b8c772e17670b8b728b5e890ef0b21
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52388
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
IPMI debug was extra spewy, so add a debug option as SPI and
other drivers have when they need to be debugged.
Change-Id: I788d67c242cac23bde9750aa3e95e3276c3f1fd7
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The default of 32 buses per hotplug bridge is rather high. Especially
for platforms that limit MMConf space to 64 buses: they run out of
numbers if there is more than a single hotplug bridge.
Lower the default to
* 8 if MMConf is limited to 64 or less buses,
* 16 if MMConf is limited to 128 or less buses.
Change-Id: I06d522dd92ceea9f4798273b26f947a5333800c3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52069
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
More relational operators were added to Kconfig in 2015. Now we can
make use of them.
Change-Id: I640e5c3ee1485348f09fcb0b0d5035eb53a2c98e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
I wished there was a way to do this in smaller steps, but with
every line fixed an error somewhere else became visible. Here
is a (probably incomplete) list of the issues:
* Only one set of parentheses was supported. This is a hard
to solve problem without a real parser (one solution is to
use an recursive RE, see below).
* The precedence order was wrong. Might have been adapted just
to give a positive result for the arbitrary state of the tree.
* Numbered match variables (e.g. $1, $2, etc.) are not local.
Calling handle_expressions() recursively once with $1, then
with $2, resulted in using the final $2 after the first
recursive call (garbage, practically).
Also, symbol and expression parsing was mixed, making things
harder to follow.
To remedy the issues:
* Split handle_symbol() out. It is called with whitespace
stripped, to keep the uglier REs in handle_expressions().
* Match balanced parentheses and quotes when splitting
expressions. In this recursive RE
/(\((?:[^\(\)]++|(?-1))*\))/
the `(?-1)` references the outer-most group, thus the whole
expression itself. So it matches a pair of parentheses with
a mix of non-parentheses and the recursive rule itself inside.
This allows us to:
* Order the expression matches according to their precedence
rules. Now we can match `<expr> '||' <expr>` first as we should
and everything else falls into its place.
* Remove the bail-out that silenced the undefined behavior.
Change-Id: Ibc1be79adc07792f0721f0dc08b50422b6da88a9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Set the SATA and SSATA REGLOCK as indicated by the Intel documentation.
Change-Id: I90e6d0e3b5a38bcd5392e26cbbb6dc4aa6a8304b
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add the SATA device to the device tree so it may be found
when trying to write SATA registers. Otherwise, it fails
on "requests hidden 00:17.0 PCI: dev is NULL!"
Change-Id: Ia309805ffd6e97d04b5cf4a0344eaac4c4d0adb6
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Set MSR locks as indicated by the Intel documents.
The following MSRs settings are locked:
MSR_FEATURE_CONFIG AES enable/disable lock
TURBO_ACTIVATION_RATIO_LOCK
This also adds PARALLEL_MP_AP_WORK to enable running on APs to set
each CPU MSR.
Change-Id: Iacf495f0880d42b378cb0d2c37940d50a511c430
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
MPTS is currently not executed by the AML interpreter.
Use Method (\\_SB.MPTS) instead of
Scope (\\_SB)
Method (MPTS)
ScopeEnd
Tested on Prodrive Hermes. MPTS is now executed at S5.
Change-Id: I9074eb4ba55aab3f9a47ae5e3c3ddd338406a5e4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: <wouter.eckhardt@prodrive-technologies.com>
Since there are some differences between picasso PSP svc and cezanne PSP
svc, each platform should have their own svc wrapper.
Moreover cezanne PSP will drop unused parameters from
update_psp_bios_dir and save_uapp_data so make wrapper around it.
BUG=b:182477057
BRANCH=none
TEST=build psp_verstage and boot on zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I69f998865fc3184ea8900a431924a315c5ee9133
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52307
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
psp_verstage is not specific to picasso. There might be picasso-specific
code but move everything into common as a first step. While developing
psp_verstage for cezanne picasso-specific code will move back to picasso
directory.
BUG=b:182477057
BRANCH=none
TEST=build psp_verstage on zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ifb1df0d82b972f28be2ffebd476c2553cbda9810
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This change implements `gpio_snapshot()` and `gpio_verify_snapshot()`
callbacks that are useful for debugging any GPIO configuration changes
across FSP-S. These can be utilized by all Intel SoCs that make use of
the common block GPIO driver.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I82a1f125c490b9d6e26e6e9527c2fcd55bb9d429
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Traditionally, for each Intel platform using FSP, FSP-S has at some
point configured GPIOs differently than the mainboard configuration in
coreboot. This has resulted in various side-effects in coreboot,
payload and OS because of misconfigured GPIOs. On more recent Intel
platforms, a UPD `GpioOverride` is added that coreboot can use to
ensure that FSP does not touch any GPIO configuration.
This change adds a debug option `CHECK_GPIO_CONFIG_CHANGES` to fsp2_0
driver in coreboot that makes a platform callback `gpio_snapshot` to
snapshot GPIO configuration before making a call to FSP SiliconInit
and Notify phases. This snapshot is then compared against the GPIO
configuration using platform callback `gpio_verify_snapshot` after
returning from FSP. The callbacks are not added to romstage (FSP-M)
because mainboard configures all pads in ramstage.
This debug hook allows developers to dump information about any pads
that have a different configuration after call to FSP in ramstage. It
is useful to identify missed UPD configurations or bugs in FSP that
might not honor the UPDs set by coreboot.
This debug hook expects the platform to implement the callbacks
`gpio_snapshot` and `gpio_verify_snapshot`. These can be implemented
as part of the common GPIO driver for platforms using
FSP2.0+. Platforms that implement this support must select the config
`HAVE_GPIO_SNAPSHOT_VERIFY_SUPPORT` to make the debug config
`CHECK_GPIO_CONFIG_CHANGES` visible to user.
Proposal for the GPIO snapshot/verify support was discussed in the RFC
CB:50829.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I5326fc98b6eba0f8ba946842253b288c0d42c523
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50989
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add ACPI code to enable the backlight when we enter the OS.
BUG=b:184198808
TEST=Backlight enabled in the OS
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I3e0a6c06120ac5abf0a0d82494e03d9cf80c1f8c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52113
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Nikolai Vyssotski