Until recently, there were two options to build edk2, UefiPayloadPkg and
CorebootPayloadPkg. Now, there is only one, UefiPayloadPkg but soon,
there will be Universal Payload.
It makes more sense, as the official edk2 repository doesn't work with
coreboot, to have the build target and repository separate. That will
allow for building either UefiPayloadPkg or Universal Payload from the
official repository, MrChromebox' fork or a custom repository.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: If7f12423058ef69838741f384495ca766ccea083
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Add EC memory layout and Q events for Intel Alder Lake based boards,
the "StarBook Mk VI" and "StarFighter Mk I", which both use the ITE
5570E.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I8cea386ba91d076084002738fe7041834deea311
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add the `eeprom_read_serial()` function to read serials from the EEPROM.
Note that there's only one buffer now: this means only one serial can be
accessed at the same time, and the buffer needs to be cleared so that it
does not contain old data from other serials. Given that the serials are
copied one at a time into SMBIOS tables, having one shared buffer is not
a problem.
Change-Id: I5c9781e4e599043be756514cfd6dd86dedcf580c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67275
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PCH's SGPIO pads are connected to a buffer chip that is powered from
the always-on +3V3_AUX rail. For some cursed reason, when the SGPIO pads
stay configured as SGPIO when a Poseidon system shuts down, voltage from
the +3V3_AUX-powered buffer chip will leak into the +5V rail through the
SATA backplane. Just pulling the SGPIO pads low before the system powers
off stops the +5V rail from being cross-powered.
This issue has only been observed in S5, but it's very likely other
sleep states are affected as well. Thus, always pull the SGPIO pins
low before entering ACPI S3 or deeper because the power supply will
turn off in these states as well.
TEST=Obtain a Poseidon system, verify that the +5V rail is cross-powered
after going to S5. We measured 0.17V on our system, but voltages as
high as 0.6V were measured on other systems. Verify that unplugging
the SGPIO cable going to the SATA backplane results in the +5V rail
voltage dropping to 0V, which indicates that the voltage leakage is
exclusively coming from the SGPIO and SATA backplane. Finally, make
sure that the +5V rail voltage drops to 0V after going into ACPI S5
with this patch applied and the SGPIO cable connected.
Change-Id: Ic872903d5fcdd1c17e02b4c06d5ba29889fbc27d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Update the README with new instructions for Debian 11 and MX Linux.
Also add the build dependencies.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I6942b9532e8d82f7fc5d6455c96913bcba6e983e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
According to Intel document number 336561, GLK has UFS (0x1d),
so add the PCI interrupt.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I68bac590bd1a9a0b8213440e882c8f431f06c95f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67680
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to Intel document number 336561, G, SD Card (0x1b)
does not exist on GLK, so remove it.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I6921fc3db430c76ec54cf832ce51c627a507385c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67679
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The intention of predefining driver strength is to avoid that the OS
SD-Card driver changes this setting.
Change-Id: I02fdac94462da1cd77f8dc972faf16f28d94c946
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
To be able to change the MAC addresses, it is necessary that the
controllers are in D0 power state. As of FSP MR3, Intel has set the
controllers to D3 power state at the end of FSP-S TSN GbE
initialization. This patch sets the state back to D0 before the
programming of the MAC addresses.
Test:
- Build coreboot with FSP MR4 for mc_ehl2 mainboard
- Boot into Linux and check MAC addr via 'ip a'
Change-Id: I4002d58eb4332ba45c35d07820900dfd2c637f21
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change the TPM I2C freqeuncy to 1 MHz for pujjo.
BUG=b:249953707
TEST=On pujjo, all timing requirements in the spec are met.
Frequencies:
pujjo - 987.80 kHz
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: If99b5022a9b67e9c63c440a1e398d56bb2c467e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
apu/amdfw_a was only getting added to CBFS when VBOOT_SLOTS_RW_AB was
selected, but needs to be added in the RW_A only case as well
(VBOOT_SLOTS_RW_A). Since VBOOT_SLOTS_RW_AB selects VBOOT_SLOTS_RW_A,
we can guard amdfw_a and _b separately and both will be added in the
RW_AB case.
TEST=build google/zork with VBOOT_SLOTS_RW_A or VBOOT_SLOTS_RW_AB
selected, ensure amdfw_a and amdfw_b are added to correct CBFS regions
as appropriate.
Change-Id: Ic8048e869d7449eeb1ac10bfec4a5646b848d6a8
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68126
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
apu/amdfw should be restricted to the RO region only when building with
VBOOT + any RW region (RW_A or RW_A + RW_B); it is not tied to ChromeOS
in any way. Fix guarding to match newer AMD platforms (eg, CZN/MDN).
TEST=build google/zork without CHROMEOS, with VBOOT_SLOTS_RW_A
Change-Id: I32d7fa7a4b3d41107cfdba96128a4a75f7066c6f
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68125
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
RaptorLake introduces the support of the Voltage Regulator Fast Vmode
feature. When enabled, it makes the SoC throttle when the current
exceeds the I_TRIP threshold. This threshold should be between
Iccmax.app and Iccmax and take into account the specification of the
Voltage Regulator of the system.
This change provides a mean to:
1. Enable the feature via the `vr_config->enable_fast_vmode'. If no
I_TRIP value is supplied FSPs picks an adapted I_TRIP value for
the current SoC assuming a Voltage Regulator error accuracy of
6.5%.
2. Set the I_TRIP threshold via the `vr_config->fast_vmode_i_trip'
field.
These new fields are considered independent from the other `vr_config'
fields so that the board configuration does not have to unnecessarily
supply other VR settings to enable Fast VMode.
Information about the Fast VMode Feature can be found in the following
Intel documents:
- 627270 ADL and RPL Processor Family Core and Uncore BIOS
Specification
- 724220 RaptorLake Platform Fast V-Mode
- 686872 RaptorLake Lake U P H Platform
BUG=b:243120082
BRANCH=firmware-brya-14505.B
TEST=Read I_TRIP from the Pcode and verify consistency with
a few `enable_fast_vmode' and `fast_vmode_i_trip' settings.
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Change-Id: I313acf01c534d0d32620a9dedba7cf3b304ed2ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Based on DMTF SMBIOS Specification 3.5.0
Signed-off-by: Erik van den Bogaert <ebogaert@eltan.com>
Change-Id: I710124ca88dac9edb68aab98cf5950aa16c695d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67926
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
use function to check if pci device is on a particular bus
number.
TEST: compiled and qemu run successfully
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Change-Id: I4a3e96381c29056de71953ea2c39cd540f3df191
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68103
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
add functions to check whether a device is enabled pci
device or a pci device on a specific bus number.
TEST: compile and qemu run successfully
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Change-Id: I3257c8404017372f6cdd9f6cf9453502447343a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68101
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change updates scl_lcnt, scl_hcnt, sda_hold value for I2C5 to
follow I2C specification.
I2C_TCHPAD_SCL high period time is from 0.53 us to 0.6952 us.
I2C_TCHPAD_SDA hold time is from 0.13 us to 0.4623 us.
BUG=b:249031186
BRANCH=brya
TEST=EE check OK with test FW and TP function is normal.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I5977f0dbba8924cc8a1c72c36358d6ba6f2de940
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67920
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Configure eMMC DLL tuning values for Pujjo board.
BUG=b:241854926
TEST=Use the value to boot on Pujjo successfully.
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: Ic36c817fa546741e394668297ca43db3a45ee105
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68095
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
An optional dGPU can be connected to the second PEG bridge:
-[0000:00]-+-00.0 Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller
+-01.0-[01]--
+-01.1-[02]----00.0 NVIDIA Corporation GK208M [GeForce GT 730M]
It's possible that the 01.0 bridge is never populated, but we have to
leave it on anyway so 01.1 can be enumerated.
Change-Id: Ieab7a7bf3b31b4ee9d9f12b5d827d866c87356e1
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Given the embedded nature, the Halo SKU, SO-DIMMs and 1 DIMM per
channel, `mobile` seems to come closest.
Change-Id: Ia27f1e4dec0a0d06be3d8c08bfe82becd41a2149
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67399
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
BUG=b:250470706
TEST=Boot to OS on pujjo and check that stylus GPIO are
configured based on fw_config.
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I4218748cb06426a918d89f688599c652062ac78c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68075
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The values in this patch were found in the following datasheets:
* 334819 (APL)
* 336561 (GLK)
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I14c5933b9022703c8951da7c6a26eb703258ec37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The Lite Mk IV's can enable fast charging, with support up to 100W
via USB-C PD 3.0.
The default for this is disabled, as it can reduce battery life
span. This patch adds the option to enable fast charging, by
writing 0x01 to 0x18 in the EC space.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ie01eb59d3f41b242190973fd9c58b1494320c12a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add variant specific cmos files, which avoid options like "FastCharge"
existing in platforms that don't support such options.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I04264cf72d47ef719acfd144d8bf9acb0ceccc11
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add variant specific cmos files, which avoid options like "Thunderbolt"
existing in platforms that don't support such options.
This change also removes entries that were never used, including:
* smi_handler
* usb_always_on
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I359e5c5bbf29eb474f2d3bc42a8e80afc0a5d38a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Sean Rhodes