In order to make the proper decision on loading the
option rom or not the recovery mode setting needs to be
known. Normally this is detected by asking the EC,
but if recovery is requested with crossystem then the EC
does not know about it. Instead we need to check the
output flags from VbInit().
Change-Id: I09358e6fd979b4af6b37a13115ac34db3d98b09d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57474
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4223
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Since we are using VBNV to determine if developer mode is
active we do not need the messy OPROM hook magic any longer.
Change-Id: I1b9effef3ef2aa84e916060d8e61ee42515a2b7c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57473
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4222
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The OIPG package needs to have >1 member to make the chromeos_acpi
kernel driver do the right automagic sysfs topology creation.
Additionally an "unimplemented" GPIO should be reported as 0xFF
because 0 is a valid GPIO number.
verify crossystem on slippy
$ sudo crossystem | grep -e recoverysw_cur -e wpsw_cur
recoverysw_cur = (error)
wpsw_cur = 1
Change-Id: I06dff09152bde30a3ffe58b1defe9d299155472c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57471
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4221
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This config option was not enabled which was preventing
the user from enabling developer mode from recovery mode.
With this enabled we can disable the "dev mode by default"
behavior and let people enable it by entering recovery mode.
This will make the firmware behave like a typical chromeos
device.
Peppy is left in "default dev mode" until after bringup.
1) boot slippy in normal mode by default
2) enter recovery mode with servo button
3) Ctrl+D on USB keyboard to enter developer mode
4) boot slippy in developer mode
Change-Id: I414c0d10dd0489e3c89798f75a2872a43297c8d8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57350
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4220
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Those building Chromebook firmware from coreboot git might be more
interested in building without ChromeOS extras.
Change-Id: I2f176d059fd45bf4eb02cc0f3f1dcc353095d0ce
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3977
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Instead of depending on exact mobo configure general characteristic whether
dock is configured in romstage or ramstage.
X60 and T60 have superio in dock so it needs to be inited to get serial, so
it should be inited in romstage.
On X201 there is nothing useful that early in boot but it's needed to init more
to get dock working, in particular EC init needs to be done first.
Change-Id: If5072e3dec883a94cd2d5643a92f7f6c3c9feee9
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4294
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Instead define brightness up/down function and gfx device and use
preprocessor magic to glue it together.
Change-Id: I03074ae07b33c1546d229efc3e80606ddbee6300
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4282
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Do not directly check the return value of get_option, but instead compare
the returned value against a CB_CMOS_ error code, or against CB_SUCCESS.
Change-Id: I2fa7761d13ebb5e9b4606076991a43f18ae370ad
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4266
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Add a new USB location field
- Add a new "ddr_refresh_2x" field, enabled on Falco only
- Fix copy+paste bug in baskingridge
Checked that tREFI is halved during memory setup in the memory
training log:
tREFImin = 6240 << DEFAULT
C(0).tREFI = 0xc30 << MODIFIED (=3120)
C(0).tREFI = 0xc30 << MODIFIED (=3120)
Also ensure that the SD card is detected properly again.
Change-Id: Ie3a82c08df06ada9af56282b5255caefa56487f2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57349
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4219
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Compiler may do loads of optimisations around stack switch and so it's allowed
to break stack switch as it sees fit. Do it in assembly instead.
Not tested.
Change-Id: I277a62a9052e8fe9b04e7c65d149e087282ac2a2
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4286
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The function reads the Build ID and the supported function specification
version from the running EC firmware, and stores a text representation
in the provided output buffer.
Change-Id: I3b647d7f315c9b4922fa9a9c5167a80f6d82e753
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3617
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These are based on the datasheet and I included the timing
values I used from the docs.
Change-Id: Ib75b2c5e50ac09d1e4cf9dd22229bb0f0a8965a4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58540
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4234
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
In order to make the proper decision on loading the
option rom or not the developer mode setting needs to be
known. Under early firmware selection it is possible to know
the state of developer mode by a flag in out flags. Use this
flag when early firmware selection is being employed to determine
if developer mode is enabled or not.
Change-Id: I9c226d368e92ddf8f14ce4dcde00da144de2a5f3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57380
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4218
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The Linux thinkpad_acpi.c driver looks for this string while
reading information about the system it is running on.
This commit does not make the module load but it is one of
several things that the module looks for on a ThinkPad.
Change-Id: Ia48bbd85ba4d528063695345b0f968d264573341
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3779
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Currently, all Peppy boards w/ '000' SPD GPIOs have 2GB DRAM. Disable
the second DRAM channel based upon the GPIOs.
Need to change / confirm this for upcoming builds.
Change-Id: I7085ddecb80626cc0bed99ba7b174c6b80350696
Reviewed-on: https://gerrit.chromium.org/gerrit/58620
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4238
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The EC was disabling flash commands and sysjump was not working
properly. With those two fixed software sync works properly.
(Taken from I63ca00d6c94854f2b395eb736ce20792da5f8de2).
Change-Id: I9c7d1d1f1aaf7de33d0cec5f6daf648576ba8900
Reviewed-on: https://gerrit.chromium.org/gerrit/57289
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4212
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There was always exactly one elog descriptor declared and initialized, but its
contents were being accessed through a pointer that was passed back and forth
between functions instead of being accessed directly. This made the code more
verbose than it needed to be and harder to follow. To address this the
descriptor type was eliminated, its contents were turned into individual
global variables, and various functions were adjusted to no longer take the
descriptor as an argument.
Similarly, the code was more verbose and complicated than it needed to be
because of several wrapper functions which wrapped a single line of code which
called an underlying function with particular arguments and were only used
once. This makes it harder to tell what the code is doing because the call to
the real function you may already be familiar with is obscured behind a
new function you've never seen before. It also adds one more text to the file
as a whole while providing at best a marginal benefit. Those functions were
removed and their callers now call their contents directly.
Built and booted on Link. Ran mosys eventlog list. Cleared the event log
and ran mosys eventlog list again. Added 2000 events and ran mosys eventlog
list. Cleared the log again and ran mosys eventlog list.
Change-Id: I4f5f6b9f4f508548077b7f5a92f4322db99e01ca
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49310
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4245
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The elog driver's design was a bit more elaborate than it really needed to be
since it no longer had to keep track of multiple copies of the log in flash
and also in memory. This change streamlines it by removing unnecessary
compartmentalization of some bits of code, and some variables which tracked
the last entry added which were never used.
Built and booted on Link. Ran mosys eventlog list. Added 2000 events to
the event log and ran mosys eventlog list again. Cleared the log by echoing 1
into /sys/firmware/gsmi/clear_eventlog and ran mosys eventlog list.
Change-Id: I7d4cdebf2f5b1f6bb1fc70e65eca18f71b124b18
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49309
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4244
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
elog_validate_and_fill was called in exactly one place, in
elog_init_descriptor. It didn't actually do what its name implied since the
data in the event log was already "filled" by elog_init_descriptor. Likewise
elog_init_descriptor was delegating an important part of its own job, scanning
through the list of events, to elog_validate_and_fill.
Since one function was basically just a displaced part of the other which
couldn't really stand on its own, this change merges them together.
Built and booted on Link. Ran mosys eventlog list. Added 2000 events with
the SMI handler and ran mosys eventlog list again.
Change-Id: Ic899eeb18146d0f127d0dded207d37d63cbc716f
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49308
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4243
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This function was just a wrapper around elog_init_descriptor, and all it did
was pass the current backing store location and size back in so it would be
reused. Those values, which never change, are now set in
elog_setup_descriptors, eliminating those parameters to init and eliminating
the need for _reinit_.
Built and booted on Link. Ran mosys eventlog list. Added 2000 events to
the log and ran mosys eventlog list again.
Change-Id: I133768aa798dfc10f32e14db95235a88666890c3
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49307
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4242
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The event log driver keeps two copies of the event log in memory, one to
take the place of the historically memory mapped image of flash which is now
read and written manually, and one originally intended to be an in memory
cache of flash. Since both are now just copies in memory, there's no value in
having them both and keeping them in sync.
Built and booted on Link. Ran mosys eventlog list. Added 2000 events to
the log and ran mosys eventlog list again. Cleared the log by echoing a 1 into
/sys/firmware/gsmi/clear_eventlog and ran mosys eventlog list again.
Change-Id: Ibed62a10c78884849726aa15ec795ab2914afc35
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49306
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4241
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The way elog_shrink currently works is that it completely clears the data in
the flash/flash descriptor and then recreates it using the part of the log
it's going to keep as stored in the memory descriptor. That scheme depends on
there being to independent copies of the log.
This change reworks elog_shrink so that it moves the data it wants to keep
within a single descriptor and then propogates it to the other and to flash
intact. This way, when one of the descriptors goes away, all we have to do is
remove the code that would update it.
Built and booted into ChromeOS on Link. Ran mosys eventlog list. Added
2000 events to the log and ran mosys eventlog list again. Echoed a 1 into
/sys/firmware/gsmi/clear_eventlog and ran mosys eventlog list.
BRANCH=None
Change-Id: I50d77a4f00ea3c6b3e0ec8996dab1a3b31580205
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49305
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4240
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The header is at the start of the log. There's no reason to either keep a
seperate pointer to it, or to keep a copy of it in some other bit of memory.
Built and booted on Link and used 'mosys eventlog list' to list the
contents of the log. Ran
for x in $(seq 1 2000); do
cat elog.event.kernel_clean > /sys/firmware/gsmi/append_to_eventlog;
done
And ran mosys eventlog list again to verify that the log had been shrunk
correctly.
Change-Id: I2afcd52c0ce5bbb662ac56f2895cdbea28d5c2ce
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49304
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4239
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some of the pcie logic was located in pch.c as well
as pcie.c. Move all pcie logic to the same pcie.c
file. This is a straight cut-and-paste (no logic changes)
except for a rename from pch_pcie_enable() ->
pch_pcie_enable_dev().
Change-Id: I338c53039b95f255ab9ced313c51193a9d34b404
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59277
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4251
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The function to disable devices was formerly named
pch_hide_devfn(). This routine was doing more than hiding
devices. It was disabling them, i.e. turning them off.
Therefore, rename it to pch_disable_devfn(). Also, allow
external callers to this function.
Change-Id: Id5bb319d4e67892c02a39dff49e45b2811a2f016
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59276
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4250
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The iobp functions are useful to may of the southbridge
devices as certain values need to be updated to properly
initialize the devices. Therefore expose read, write, and
updated iobp functions.
Change-Id: Id7fdd8d0d9f022f92d6285ecd8f85a52024ec2bb
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59275
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4249
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
A quirk of the Kconfig used in coreboot is that config options
cannot be overriden by local config changes unless they have
a description string.
1) Add CONFIG_MAINBOARD_VENDOR="Custom" to local config
2) Build and flash coreboot
3) cat /sys/class/dmi/id/sys_vendor and look for "Custom"
Change-Id: I1b5f2124cd4a22c056c025143ae5bcaafa6b03f0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59088
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4248
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The wake device input pins are active low and the
GPIOs need to be set as inverted when they are marked
as an input so they are not spuriously logged.
Also sync pin states from Falco initial commit.
Reference change: I15d38dcc9b2fb4b2b0eb27da358fa3c343e22323
Change-Id: I66e136d389d53a367436d816fa84dacdc8e86bad
Reviewed-on: https://gerrit.chromium.org/gerrit/58334
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@google.com>
Reviewed-on: http://review.coreboot.org/4247
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Set nid 0x12 instead of nid 0x05. The DMIC is on NIC 0x12.
Change-Id: Ifc883b65a50aeec6a6d3ad02fe8418f124e6241d
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58711
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Jay Kim <yongjaek@chromium.org>
Tested-by: Jay Kim <yongjaek@chromium.org>
Reviewed-on: http://review.coreboot.org/4246
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
SPD GPIOs were being read prior to initialization in romstage_common. To
fix, pass the copy_spd function to romstage_common, to be called at the
appropriate time (after PCH init, before DRAM init).
Change-Id: I2554813e56a58c8c81456f1a53cc8ce9c2030a73
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58608
Reviewed-on: http://review.coreboot.org/4237
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There are useful values in NVS that are set at boot
and runtime and they should not be cleared on resume.
suspend/resume twice on slippy and ensure
that the USB ports are still powered on the second suspend.
Change-Id: I4bce60b02b6637f6683120ae9c4a5c64563aacf7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56941
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4210
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Make temporary buffer allocation equal with the allocation in CBMEM and
let copy_console_buffer() handle possible truncation.
When not using dynamic CBMEM the CBMEM area is initialized late in the
ramstage and should be able to hold almost as many characters as the
CBMEM can hold. We have seen 40000 was not always enough with logging
level set to spew, new default size is 0x10000.
Change-Id: If4b143fdf807e28b6766b8b99db5216b767948d5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4295
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
When using dynamic CBMEM the CBMEM area is initialized before
entering ram stage, and so we need a way smaller temporary buffer
for the CBMEM console during early bits of ram stage. In practice
around 256 bytes are needed, but keep the buffer at 1k so we make
sure we don't run out.
TEST=Boot tested on pit
BRANCH=none
BUG=none
Change-Id: I462810b7bafbcc57f8e5f9b1d1f38cfdf85fa630
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/168575
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
[km: cherry-pick 7fd1bbc0 from chromium git]
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4293
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Make sure memcpy target and a possible message telling log was truncated
stay within the allocated region for CBMEM console.
This fixes observed CBMEM corruption on platforms that do not use CBMEM
console during romstage. Those platforms will need an additional fix to
reset cursor position to zero on s3 resume.
Change-Id: I76501ca3afc716545ca76ebca1119995126a43f8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4292
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
If Vortex86EX PS/2 keyboard controller system flag bit times out,
reload controller firmware code and try again.
Abort and die after 11 tries as this means the CPU is defect. Also
inform the user by printing a message.
Change-Id: I24aec4b20d85c721c01e72686f3eb1259f9334b8
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3988
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Previously, I've set this config in mobo config, yet according to
Kyösti Mälkki this parameter is southbridge-specific and not
mobo-specific.
Change-Id: I92428aed5a69d88a371f5d7267bc54ba7530766c
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4276
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
The wake device input pins are active low and the
GPIOs need to be set as inverted when they are marked
as an input so they are not spuriously logged.
suspend/resume on slippy with trackpad wake:
8 | 2013-05-29 07:43:14 | ACPI Enter | S3
9 | 2013-05-29 07:43:18 | ACPI Wake | S3
10 | 2013-05-29 07:43:18 | Wake Source | GPIO | 12
and with power button wake:
11 | 2013-05-29 07:43:35 | ACPI Enter | S3
12 | 2013-05-29 07:43:40 | EC Event | Power Button
13 | 2013-05-29 07:43:40 | ACPI Wake | S3
14 | 2013-05-29 07:43:40 | Wake Source | Power Button | 0
Change-Id: I15d38dcc9b2fb4b2b0eb27da358fa3c343e22323
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56940
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4209
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Make the declaration and use of it conditional on the ELOG_GSMI Kconfig variable.
Change-Id: I2ef291d2f3e7d35545014e03ba8e0045da6050e5
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3987
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The EC was disabling flash commands and sysjump was not working
properly. With those two fixed software sync works properly.
Google Chrome EC MKBP driver ready, id 'slippy_no_version'
Clearing the recovery request.
EC hash:7fea29992ef72e3e64d8ffe522aa1dfa68dcb44a2da96a4c19530ea1a0bd22c4
EC-RW hash address, size are 0xffa1cfe8, 32.
Hash = 727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
Expected hash:727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
EC-RW firmware address, size are 0xffad000c, 57180.
VbEcSoftwareSync() - expected len = 57180
Computed hash of expected image:727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
VbEcSoftwareSync() updating EC-RW...
VbEcSoftwareSync() jumping to EC-RW
VbEcSoftwareSync() in RW; done
Change-Id: I63ca00d6c94854f2b395eb736ce20792da5f8de2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56821
Reviewed-on: http://review.coreboot.org/4208
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Now that there is a clearly defined boot state machine
we can add some useful post codes to indicate the current
point in the state machine by having it log a post code
before the execution of each state.
This removes the currently defined POST codes that were
used by hardwaremain in favor of a new contiguous range
that are defined for each boot state.
The reason for this is that the existing codes are mostly
used to indicate when something is done, which is confusing
for actual debug because POST code debugging relies on knowing
what is about to happen (to know what may be at fault) rather
than what has just finished.
One additonal change is added during device init step as this
step often does the bulk of the work, and frequently logs POST
codes itself. Therefore in order to keep better track of what
device is being initialized POST_BS_DEV_INIT is logged before
each device is initialized.
interrupted boot with reset button and
gathered the eventlog. Mosys has been extended to
decode the well-known POST codes:
26 | 2013-06-10 10:32:48 | System boot | 120
27 | 2013-06-10 10:32:48 | Last post code in previous boot | 0x75 | Device Initialize
28 | 2013-06-10 10:32:48 | Extra info from previous boot | PCI | 00:16.0
29 | 2013-06-10 10:32:48 | Reset Button
30 | 2013-06-10 10:32:48 | System Reset
Change-Id: Ida1e1129d274d28cbe8e49e4a01483e335a03d96
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58106
Reviewed-on: http://review.coreboot.org/4231
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
One of the most common hangs during coreboot execution
is during ramstage device init steps. Currently there
are a set of (somewhat misleading) post codes during this
phase which give some indication as to where execution
stopped, but it provides no information on what device
was actually being initialized at that point.
This uses the new CMOS "extra" log banks to store the
encoded device path of the device that is about to be
touched by coreboot. This way if the system hangs when
talking to the device there will be some indication where
to investigate next.
interrupted boot with reset button and
gathered the eventlog after several test runs:
26 | 2013-06-10 10:32:48 | System boot | 120
27 | 2013-06-10 10:32:48 | Last post code in previous boot | 0x75 | Device Initialize
28 | 2013-06-10 10:32:48 | Extra info from previous boot | PCI | 00:16.0
29 | 2013-06-10 10:32:48 | Reset Button
30 | 2013-06-10 10:32:48 | System Reset
Change-Id: I6045bd4c384358b8a4e464eb03ccad639283939c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58105
Reviewed-on: http://review.coreboot.org/4230
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This can be used to indicate sub-state within a POST
code range which can assist in debugging BIOS hangs.
For example this can be used to indicate which device
is about to be initialized so if the system hangs
while talking to that device it can be identified.
Change-Id: I2f8155155f09fe9e242ebb7204f0b5cba3a1fa1e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58104
Reviewed-on: http://review.coreboot.org/4229
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The CMOS post code storage mechanism does back-to-back
CMOS reads and writes that may be interleaved during
CPU bringup, leading to corruption of the log or of other
parts of CMOS.
Change-Id: I704813cc917a659fe034b71c2ff9eb9b80f7c949
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58102
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4227
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Duncan Laurie