175 lines
6.2 KiB
Markdown
175 lines
6.2 KiB
Markdown
# ASRock H77 Pro4-M
|
|
|
|
The ASRock H77 Pro4-M is a microATX-sized desktop board for Intel Sandy
|
|
Bridge and Ivy Bridge CPUs.
|
|
|
|
## Technology
|
|
|
|
```eval_rst
|
|
+------------------+--------------------------------------------------+
|
|
| Northbridge | :doc:`../../northbridge/intel/sandybridge/index` |
|
|
+------------------+--------------------------------------------------+
|
|
| Southbridge | Intel H77 (bd82x6x) |
|
|
+------------------+--------------------------------------------------+
|
|
| CPU socket | LGA 1155 |
|
|
+------------------+--------------------------------------------------+
|
|
| RAM | 4 x DDR3-1600 |
|
|
+------------------+--------------------------------------------------+
|
|
| Super I/O | Nuvoton NCT6776 |
|
|
+------------------+--------------------------------------------------+
|
|
| Audio | Realtek ALC892 |
|
|
+------------------+--------------------------------------------------+
|
|
| Network | Realtek RTL8111E |
|
|
+------------------+--------------------------------------------------+
|
|
| Serial | Internal header (RS-232) |
|
|
+------------------+--------------------------------------------------+
|
|
```
|
|
|
|
## Status
|
|
|
|
Tests were done with SeaBIOS 1.14.0 and slackware64-live from 2019-07-12
|
|
(linux-4.19.50).
|
|
|
|
### Working
|
|
|
|
- Sandy Bridge and Ivy Bridge CPUs (tested: i5-2500, Pentium G2120)
|
|
- Native RAM initialization with four DIMMs
|
|
- PS/2 combined port (mouse or keyboard)
|
|
- Integrated GPU by libgfxinit on all monitor ports (DVI-D, HDMI, D-Sub)
|
|
- PCIe graphics in the PEG slot
|
|
- All three additional PCIe slots
|
|
- All rear and internal USB2 ports
|
|
- All rear and internal USB3 ports
|
|
- All six SATA ports from the PCH (two 6 Gb/s, four 3 Gb/s)
|
|
- All two SATA ports from the ASM1061 PCIe-to-SATA bridge (6 Gb/s)
|
|
- Rear eSATA connector (multiplexed with one ASM1061 port)
|
|
- Gigabit Ethernet
|
|
- Console output on the serial port
|
|
- SeaBIOS 1.14.0 and 1.15.0 to boot Windows 10 (needs VGA BIOS) and Linux via
|
|
extlinux
|
|
- Internal flashing with flashrom-1.2, see
|
|
[Internal Programming](#internal-programming)
|
|
- External flashing with flashrom-1.2 and a Raspberry Pi 1
|
|
- S3 suspend/resume from either Linux or Windows 10
|
|
- Poweroff
|
|
|
|
### Not working
|
|
|
|
- Booting from the two SATA ports provided by the ASM1061
|
|
- Automatic fan control with the NCT6776D Super I/O
|
|
|
|
### Untested
|
|
|
|
- EHCI debug
|
|
- S/PDIF audio
|
|
- Other audio jacks than the green one, and the front panel header
|
|
- Parallel port
|
|
- Infrared/CIR
|
|
- Wakeup from anything but the power button
|
|
|
|
## Flashing coreboot
|
|
|
|
```eval_rst
|
|
+---------------------+------------+
|
|
| Type | Value |
|
|
+=====================+============+
|
|
| Socketed flash | yes |
|
|
+---------------------+------------+
|
|
| Model | W25Q64.V |
|
|
+---------------------+------------+
|
|
| Size | 8 MiB |
|
|
+---------------------+------------+
|
|
| Package | DIP-8 |
|
|
+---------------------+------------+
|
|
| Write protection | no |
|
|
+---------------------+------------+
|
|
| Dual BIOS feature | no |
|
|
+---------------------+------------+
|
|
| Internal flashing | yes |
|
|
+---------------------+------------+
|
|
```
|
|
|
|
The flash is divided into the following regions, as obtained with
|
|
`ifdtool -f rom.layout backup.rom`:
|
|
```
|
|
00000000:00000fff fd
|
|
00200000:007fffff bios
|
|
00001000:001fffff me
|
|
```
|
|
|
|
### Internal programming
|
|
|
|
The main SPI flash can be accessed using flashrom. By default, only
|
|
the BIOS region of the flash is writable. If you wish to change any
|
|
other region (Management Engine or flash descriptor), then an external
|
|
programmer is required.
|
|
|
|
The following command may be used to flash coreboot:
|
|
|
|
```
|
|
$ sudo flashrom --noverify-all --ifd -i bios -p internal -w coreboot.rom
|
|
```
|
|
|
|
The use of `--noverify-all` is required since the Management Engine
|
|
region is not readable even by the host.
|
|
|
|
```eval_rst
|
|
In addition to the information here, please see the
|
|
:doc:`../../tutorial/flashing_firmware/index`.
|
|
```
|
|
|
|
## Hardware monitoring and fan control
|
|
|
|
There are two fan headers for the CPU cooler, CPU_FAN1 and CPU_FAN2. They share
|
|
a single fan tachometer input on the Super I/O while some dedicated logic
|
|
selects which one is allowed to reach it. Two GPIO pins on the Super I/O are
|
|
used to control that logic. The firmware has to set them; coreboot selects
|
|
CPU_FAN1 by default, but the user can change that setting if it was built with
|
|
CONFIG_USE_OPTION_TABLE:
|
|
|
|
```
|
|
$ sudo nvramtool -e cpu_fan_header
|
|
[..]
|
|
$ sudo nvramtool -w cpu_fan_header=CPU_FAN2
|
|
$ sudo nvramtool -w cpu_fan_header=None
|
|
$ sudo nvramtool -w cpu_fan_header=Both
|
|
```
|
|
|
|
The setting will take effect after a reboot. Selecting and connecting both fan
|
|
headers is possible but the Super I/O will report wrong fan speeds.
|
|
|
|
Currently there is no automatic, OS-independent fan control, but a software
|
|
like `fancontrol` from the lm-sensors package can be used instead.
|
|
|
|
## Serial port header
|
|
|
|
Serial port 1, provided by the Super I/O, is exposed on a pin header. The
|
|
RS-232 signals are assigned to the header so that its pin numbers map directly
|
|
to the pin numbers of a DE-9 connector. If your serial port doesn't seem to
|
|
work, check if your bracket expects a different assignment. Also don't try to
|
|
connect it directly to a device that operates at TTL levels - it would need a
|
|
level converter like a MAX232.
|
|
|
|
Here is a top view of the serial port header found on this board:
|
|
|
|
+---+---+
|
|
N/C | | 9 | RI -> pin 9
|
|
+---+---+
|
|
Pin 8 <- CTS | 8 | 7 | RTS -> pin 7
|
|
+---+---+
|
|
Pin 6 <- DSR | 6 | 5 | GND -> pin 5
|
|
+---+---+
|
|
Pin 4 <- DTR | 4 | 3 | TxD -> pin 3
|
|
+---+---+
|
|
Pin 2 <- RxD | 2 | 1 | DCD -> pin 1
|
|
+---+---+
|
|
|
|
## eSATA
|
|
|
|
The eSATA port on the rear I/O panel and the internal connector SATA3_A1 share
|
|
the same controller port on the ASM1061. Attaching an eSATA drive causes a
|
|
multiplexer chip to disconnect the internal port from the SATA controller and
|
|
connect the eSATA port instead. This can be seen on GP23 of the Super I/O
|
|
GPIOs: it is '0' when something is connected to the eSATA port and '1'
|
|
otherwise.
|