coreboot-kgpe-d16/Documentation/soc/amd/family17h.md

12 KiB
Executable File
Raw Blame History

AMD Family 17h in coreboot

Abstract

Beginning with Family 17h products (a.k.a. “Zen” cores), AMD changed their paradigm for initializing the system and this requires major modifications to the execution flow of coreboot. This file discusses the new boot flow, and challenges, and the tradeoffs of the initial port into coreboot.

Introduction

Family 17h products are x86-based designs. This documentation assumes familiarity with x86, its reset state and its early initialization requirements.

To the extent necessary, the role of the AMD Secure Processor (a.k.a. Platform Security Processor or PSP) in system initialization is addressed here. The PSP specification1 is available only with an NDA. coreboot relies on util/amdfwtool to build the structures and add various other firmware to the final image2. The Family 17h PSP design guide adds a new BIOS Directory Table, similar to the PSP Directory Table.

Support in coreboot for modern AMD products is based on AMDs reference code: AMD Generic Encapsulated Software Architecture (AGESATM). AGESA contains the technology for enabling DRAM, configuring proprietary core logic, assistance with generating ACPI tables, and other features.

AGESA for products earlier than Family 17h is known as v5 or Arch20083. Also note that coreboot currently contains both open source AGESA and closed source implementations (binaryPI) compiled from AGESA.

The first AMD Family 17h device ported to coreboot is codenamed “Picasso”4, and will be added to soc/amd/picasso.

Additional Definitions

  • PSP, Platform Security Processor: Onboard ARM processor that runs alongside the main x86 processor; may be viewed as analogous to the IntelR Management Engine
  • FCH, Fusion Control Hub, the logical southbridge within the SOC
  • ABL - AGESA Bootloader - Processor initialization code that runs on the PSP
  • PSP Directory Table - A structured list of pointers to PSP firmware and other controller binaries
  • BIOS Directory Table - A structured list of pointers to BIOS related firmware images
  • Embedded Firmware Structure - Signature and pointers used by the PSP to locate the PSP Directory Table and BIOS Directory Table; these items are generated during coreboot build and are located in the SPI ROM
  • vboot - The generic technology name for verifying/choosing a RW A/B or fallback RO path.
  • verstage - The code (vboot) to verify the firmware contained in the writable section of the SPI ROM, traditionally run on the x86 processor, and in some cases a separate stage added to coreboot
  • vboot app - A portion of vboot technology designed and compiled to run on the PSP
  • APCB - AMD PSP Customization Block - A binary containing PSP and system configuration preferences (analogous to v5 BUILDOPT_ options), and generated by APCBTool to be added to coreboot/utils later
  • APOB - AGESA PSP Output Buffer - A buffer in main memory for storing AGESA BootLoader output. There are no plans for this to be parsed by coreboot

Problem Statements

AMD has ported early AGESA features to the PSP, which now discovers, enables and trains DRAM. Unlike any other x86 device in coreboot, a Picasso system has DRAM online prior to the first instruction fetch.

Cache-as-RAM (CAR) is no longer a supportable feature in AMD hardware. Early code expecting CAR behavior must account for writes escaping the L2 cache and going to DRAM.

Without any practical need for CAR, or DRAM initialization, coreboot should arguably skip bootblock and romstage, and possibly use ramstage as the BIOS image. This approach presents a number of challenges:

  • At the entry of ramstage, x86 processors are in flat protected mode. Picassos initial state is nearly identical to any other x86 at reset, except its CS shadow registers base and limit put its execution within DRAM, not at 0xfffffff0. Picasso requires initial programming and entry into protected mode prior to ramstage.
  • coreboot expects cbmem initialization during romstage.

AGESA supporting Picasso is now at v9. Unlike Arch2008, which defines granular entry points for easy inclusion to a legacy BIOS, v9 is rewritten for compilation into a UEFI. The source follows UEFI standards, i.e. assumes the presence of UEFI phases, implements dependency expressions, much functionality is rewritten as libraries, etc. It would, in no way, fit into the v5 model used in coreboot.

  • For the foreseeable future, AGESA source will distributed only under NDA. Furthermore, because AGESA's integrated debug services divulge NDA information, no debug builds will be released to the general public.

Basic Pre-x86 Boot Flow

The following steps occur prior to x86 processor operation.

  • System power on
  • PSP executes immutable on-chip boot ROM
  • PSP locates the Embedded Firmware Table and PSP Directory Table in the SPI ROM
  • PSP verifies and executes the PSP off-chip bootloader
  • ChromeOS systems:
    • Off-chip bootloader attempts to locate vboot app via the RO BIOS Directory Table
    • If vboot app is not found, booting continues with ABLs below
    • vboot app initializes, setting up GPIOs, UART if needed, communication path to the EC, and the SPI controller for direct access to the flash device.
    • vboot app verifies the RW sections (as is typically performed by the main processor)
    • vboot app locates the Embedded Firmware Directory within the verified FMAP section and passes a pointer to the PSP bootloader. If the verification fails, it passes a pointer to the RO header to the bootloader.
  • PSP parses the PSP Directory Table to find the ABLs and executes them
  • An ABL parses the APCB for system configuration preferences
  • An ABL initializes system main memory, locates the compressed BIOS image in the SPI ROM, and decompresses it into DRAM
  • An ABL writes the APOB to DRAM for consumption by the x86-based AGESA
  • PSP releases the x86 processor from reset. The x86 core fetches and executes instructions from the reset vector

Picasso Reset Vector and First Instructions

As mentioned above, prior to releasing the x86 main core from reset, the PSP decompresses a BIOS image into DRAM. The PSP uses a specific BIOS Directory Table entry type to determine the source address (in flash), the destination address (in DRAM), and the destination size. The decompressed image is at the top of the destination region. The PSP then

Calculates the x86 reset vector as

reset_vector	= dest_addr + dest_size - 0x10

Sets x86 CS descriptor shadow register to

base		= dest_addr + dest_size - 0x10000
limit		= 0xffff

Like all x86 devices, the main core is allowed to begin executing instructions with

CS:IP		= 0xf000:0xfff0

For example, assume the BIOS Directory Table indicates

destination	= 0x9b00000
size		= 0x300000

… then the BIOS image is placed at the topmost position the region 0x9b00000-0x9dfffff and

reset_vector	= 0x9dffff0
CS_shdw_base	= 0x9df0000
CS:IP		= 0xf000:0xfff0

Although the x86 behaves as though it began executing at 0xfffffff0 i.e. 0xf000:0xfff0, the initial GDT load must use the physical address of the table and not the typical CS-centric address. And, the first jump to protected mode must jump to the physical address in DRAM. Any code that is position-dependent must be linked to run at the final destination.

Implementation for coreboot

Supporting Picasso doesnt fit perfectly with many of the coreboot assumptions about x86 processors. Changes are introduced primarily into arch/x86 to accommodate a processor starting in DRAM and at a nontraditional reset vector.

CAR and early stages

The traditional coreboot bootblock and romstage rely on cache-as-RAM and a linker script that positions temporary storage accordingly. A substitute for the DCACHE variables, called EARLYRAM, is introduced. Like DCACHE, this allows for a consistent mapping of early regions required across multiple stages prior to cbmem coming online. Examples are the _preram_cbmem_console and _timestamp.

Due to Picasso's unique nature of starting with DRAM already available, no early stages run as execute-in-place (XIP). All post-bootblock stages are copied from the BIOS flash into DRAM for faster performance, and these regions are marked reserved later in POST.

Unlike CAR-based systems, and because Picasso does not run early stages as XIP, its early stages are not constrained in their use of .bss or .data sections. All stages' .bss is zeroed, and all .data sections are fully R/W at load time.

bootblock

Picasso uses a bootblock that mirrors a traditional bootblock as much as possible. Because the image is loaded by the PSP, the bootblock is not restricted to the top of the BIOS flash device. The compressed image is added into the PSP's amdfw.rom build.

vboot app and verstage

Development is currently underway for the vboot app, and potentially an x86-based verstage companion. This document shall be updated once the design is finalized and functioning. Support for the PSP honoring the presence of the vboot app is available only in certain SKUs.

romstage and postcar

A traditional romstage is maintained for Picasso. The primary reason for this choice is to remain compatible with coreboot conventions and to support the FSP 2.0 driver. Picasso's romstage uses an fsp_memory_init() call to glean the memory map from AGESA. (See below.) fsp_memory_init() brings cbmem online before returning to the caller.

No postcar stage is required or supported.

AGESA v9 on Picasso

Due to the current restriction on publishing AGESA source, a pre-built binary solution remains a requirement. Modifying v9 to conform to the existing v5 binaryPI interface was considered impractical.

Given the UEFI nature of modern AGESA, and the existing open source work from Intel, Picasso shall support AGESA via an FSP-like prebuilt image. The Intel Firmware Support Package5 combines reference code with EDK II source to create a modular image with discoverable entry points. coreboot source already contains knowledge of FSP, how to parse it, integrate it, and how to communicate with it. Picasso's FSP is compatible with rev. 2.0 of the External Architecture Specification. Deviations, e.g., no FSP-T support, shall be published in an Integration Guide.

APCB setup

APCBs are used to provide the PSP with SPD information and optionally a set of GPIOs to use for selecting which SPD to load.

Prebuilt

The picasso Makefile expects APCBs to be located in 3rdparty/blobs/mainboard/$(MAINBOARDDIR). If you have a pre-built binary just add the following to your mainboard's Makefile.

# i.e., 3rdparty/blobs/mainboard/amd/mandolin/APCB_mandolin.bin
APCB_SOURCES = mandolin

Generating APCBs

If you have a template APCB file, the apcb_edit tool can be used to inject the SPD and GPIOs used to select the correct slot. Entries should match this pattern {NAME}_x{1,2}. There should be a matching SPD hex file in SPD_SOURCES_DIR matching the pattern {NAME}.spd.hex. The _x{1,2} suffix denotes single or dual channel. Up to 16 slots can be used. If a slot is empty, the special empty keyword can be used. This will generate an APCB with an empty SPD.

APCB_SOURCES =  hynix-HMA851S6CJR6N-VK_x1   # 0b0000
APCB_SOURCES += hynix-HMAA1GS6CMR6N-VK_x2   # 0b0001
APCB_SOURCES += empty                       # 0b0010
APCB_SOURCES += samsung-K4A8G165WC-BCWE_x1  # 0b0011

APCB Board ID GPIO configuration.

The GPIOs determine which memory SPD will be used during boot.

# APCB_BOARD_ID_GPIO[0-3] = GPIO_NUMBER GPIO_IO_MUX GPIO_BANK_CTL
# GPIO_NUMBER: FCH GPIO number
# GPIO_IO_MUX: Value write to IOMUX to configure this GPIO
# GPIO_BANK_CTL: Value write to GPIOBankCtl[23:16] to configure this GPIO

APCB_BOARD_ID_GPIO0 = 121 1 0
APCB_BOARD_ID_GPIO1 = 120 1 0
APCB_BOARD_ID_GPIO2 = 131 3 0
APCB_BOARD_ID_GPIO3 = 116 1 0

Footnotes

  1. AMD Platform Security Processor BIOS Architecture Design Guide for AMD Family 17h Processors (PID #55758) and AMD Platform Security Processor BIOS Architecture Design Guide (PID #54267) for earlier products
  2. PSP Integration
  3. https://www.amd.com/system/files/TechDocs/44065_Arch2008.pdf
  4. https://en.wikichip.org/wiki/amd/cores/picasso
  5. https://www.intel.com/content/www/us/en/intelligent-systems/intel-firmware-support-package/intel-fsp-overview.html