coreboot-kgpe-d16/Documentation/RFC/intel-gpio-cleanup.md

4.9 KiB

Background

CB:31250 ("soc/intel/cannonlake: Configure GPIOs again after FSP-S is done") introduced a workaround in coreboot for soc/intel/cannonlake platforms to save and restore GPIO configuration performed by mainboard across call to FSP Silicon Init (FSP-S). This workaround was required because FSP-S was configuring GPIOs differently than mainboard resulting in boot and runtime issues because of misconfigured GPIOs. This issue was observed on google/hatch mainboard and was raised with Intel to get the FSP behavior fixed. Until the fix in FSP was available, this workaround was used to ensure that the mainboards can operate correctly and were not impacted by the GPIO misconfiguration in FSP-S.

The issues observed on google/hatch mainboard were fixed by adding (if required) and initializing appropriate FSP UPDs. This UPD initialization ensured that FSP did not configure any GPIOs differently than the mainboard configuration. Fixes included:

  • CB:31375 ("soc/intel/cannonlake: Configure serial debug uart")
  • CB:31520 ("soc/intel/cannonlake: Assign FSP UPDs for HPD and Data/CLK of DDI ports")
  • CB:32176 ("mb/google/hatch: Update GPIO settings for SD card and SPI1 Chip select")
  • CB:34900 ("soc/intel/cnl: Add provision to configure SD controller write protect pin")

With the above changes merged, it was verified on google/hatch mainboard that the workaround for GPIO reconfiguration was not needed. However, at the time, we missed dropping the workaround in 'soc/intel/cannonlake`. Currently, this workaround is used by the following mainboards:

  • google/drallion
  • google/sarien
  • purism/librem_cnl
  • system76/lemp9

As verified on google/hatch, FSP v1263 included all UPD additions that were required for addressing this issue.

Proposal

  • The workaround can be safely dropped from soc/intel/cannonlake only after the above mainboards have verified that FSP-S does not configure any pads differently than the mainboard in coreboot. Since the fix included initialization of FSP UPDs correctly, the above mainboards can use the following diff to check what pads change after FSP-S has run:
diff --git a/src/soc/intel/common/block/gpio/gpio.c b/src/soc/intel/common/block/gpio/gpio.c
index 28e78fb366..0cce41b316 100644
--- a/src/soc/intel/common/block/gpio/gpio.c
+++ b/src/soc/intel/common/block/gpio/gpio.c
@@ -303,10 +303,10 @@ static void gpio_configure_pad(const struct pad_config *cfg)
                /* Patch GPIO settings for SoC specifically */
                soc_pad_conf = soc_gpio_pad_config_fixup(cfg, i, soc_pad_conf);

-               if (CONFIG(DEBUG_GPIO))
+               if (soc_pad_conf != pad_conf)
                        printk(BIOS_DEBUG,
-                       "gpio_padcfg [0x%02x, %02zd] DW%d [0x%08x : 0x%08x"
-                       " : 0x%08x]\n",
+                       "%d: gpio_padcfg [0x%02x, %02zd] DW%d [0x%08x : 0x%08x"
+                       " : 0x%08x]\n", cfg->pad,
                        comm->port, relative_pad_in_comm(comm, cfg->pad), i,
                        pad_conf,/* old value */
                        cfg->pad_config[i],/* value passed from gpio table */

Depending upon the pads that are misconfigured by FSP-S, these mainboards will have to set UPDs appropriately. Once this is verified by the above mainboards, the workaround implemented in CB:31250 can be dropped.

  • The fix implemented in FSP/coreboot for soc/intel/cannonlake platforms is not really the right long term solution for the problem. Ideally, FSP should not be touching any GPIO configuration and letting coreboot configure the pads as per mainboard design. This recommendation was accepted and implemented by Intel starting with Jasper Lake and Tiger Lake platforms using a single UPD GpioOverride that coreboot can set so that FSP does not change any GPIO configuration. However, this implementation is not backported to any older platforms. Given the issues that we have observed across different platforms, the second proposal is to:

    • Add a Kconfig CHECK_GPIO_CONFIG_CHANGES that enables checks in coreboot to stash GPIO pad configuration before various calls to FSP and compares the configuration on return from FSP.
    • This will have to be implemented as part of drivers/intel/fsp/fsp2_0/ to check for the above config selection and make callbacks gpio_snapshot() and gpio_verify_snapshot() to identify and print information about pads that have changed configuration after calls to FSP.
    • This config can be kept disabled by default and mainboard developers can enable them as and when required for debug.
    • This will be helpful not just for the soc/intel/cannonlake platforms that want to get rid of the above workaround, but also for all future platforms using FSP to identify and catch any GPIO misconfigurations that might slip in to any platforms (in case the GpioOverride UPD is not honored by any code path within FSP).