541 lines
14 KiB
C
541 lines
14 KiB
C
/* Copyright 2016 The Chromium OS Authors. All rights reserved.
|
|
* Use of this source code is governed by a BSD-style license that can be
|
|
* found in the LICENSE file.
|
|
*/
|
|
|
|
/* I2C port module for ISH */
|
|
|
|
#include "common.h"
|
|
#include "console.h"
|
|
#include "config_chip.h"
|
|
#include "gpio.h"
|
|
#include "hooks.h"
|
|
#include "i2c.h"
|
|
#include "registers.h"
|
|
#include "ish_i2c.h"
|
|
#include "task.h"
|
|
#include "timer.h"
|
|
#include "hwtimer.h"
|
|
#include "util.h"
|
|
|
|
#define CPUTS(outstr) cputs(CC_I2C, outstr)
|
|
#define CPRINTS(format, args...) cprints(CC_I2C, format, ## args)
|
|
#define CPRINTF(format, args...) cprintf(CC_I2C, format, ## args)
|
|
|
|
/*25MHz, 50MHz, 100MHz, 120MHz, 40MHz, 20MHz, 37MHz*/
|
|
static uint16_t default_hcnt_scl_100[] = {
|
|
4000, 4420, 4920, 4400, 4000, 4000, 4300
|
|
};
|
|
|
|
static uint16_t default_lcnt_scl_100[] = {
|
|
4720, 5180, 4990, 5333, 4700, 5200, 4950
|
|
};
|
|
|
|
static uint16_t default_hcnt_scl_400[] = {
|
|
600, 820, 1120, 800, 600, 600, 450
|
|
};
|
|
|
|
static uint16_t default_lcnt_scl_400[] = {
|
|
1320, 1380, 1300, 1550, 1300, 1200, 1250
|
|
};
|
|
|
|
static uint16_t default_hcnt_scl_1000[] = {
|
|
260, 260, 260, 305, 260, 260, 260
|
|
};
|
|
|
|
static uint16_t default_lcnt_scl_1000[] = {
|
|
500, 500, 500, 525, 500, 500, 500
|
|
};
|
|
|
|
static uint16_t default_hcnt_scl_hs[] = { 160, 300, 160, 166, 175, 150, 162 };
|
|
static uint16_t default_lcnt_scl_hs[] = { 320, 340, 320, 325, 325, 300, 297 };
|
|
|
|
|
|
static uint8_t bus_freq[ISH_I2C_PORT_COUNT] = {
|
|
I2C_FREQ_120, I2C_FREQ_120, I2C_FREQ_120
|
|
};
|
|
|
|
static struct i2c_context i2c_ctxs[ISH_I2C_PORT_COUNT] = {
|
|
{
|
|
.bus = 0,
|
|
.base = (uint32_t *) ISH_I2C0_BASE,
|
|
.speed = I2C_SPEED_400KHZ,
|
|
.int_pin = ISH_I2C0_IRQ,
|
|
},
|
|
{
|
|
.bus = 1,
|
|
.base = (uint32_t *) ISH_I2C1_BASE,
|
|
.speed = I2C_SPEED_400KHZ,
|
|
.int_pin = ISH_I2C1_IRQ,
|
|
},
|
|
{
|
|
.bus = 2,
|
|
.base = (uint32_t *) ISH_I2C2_BASE,
|
|
.speed = I2C_SPEED_400KHZ,
|
|
.int_pin = ISH_I2C2_IRQ,
|
|
},
|
|
};
|
|
|
|
static struct i2c_bus_info board_config[ISH_I2C_PORT_COUNT] = {
|
|
{
|
|
.bus_id = 0,
|
|
.std_speed.sda_hold = DEFAULT_SDA_HOLD_STD,
|
|
.fast_speed.sda_hold = DEFAULT_SDA_HOLD_FAST,
|
|
.fast_plus_speed.sda_hold = DEFAULT_SDA_HOLD_FAST_PLUS,
|
|
.high_speed.sda_hold = DEFAULT_SDA_HOLD_HIGH,
|
|
},
|
|
{
|
|
.bus_id = 1,
|
|
.std_speed.sda_hold = DEFAULT_SDA_HOLD_STD,
|
|
.fast_speed.sda_hold = DEFAULT_SDA_HOLD_FAST,
|
|
.fast_plus_speed.sda_hold = DEFAULT_SDA_HOLD_FAST_PLUS,
|
|
.high_speed.sda_hold = DEFAULT_SDA_HOLD_HIGH,
|
|
},
|
|
{
|
|
.bus_id = 2,
|
|
.std_speed.sda_hold = DEFAULT_SDA_HOLD_STD,
|
|
.fast_speed.sda_hold = DEFAULT_SDA_HOLD_FAST,
|
|
.fast_plus_speed.sda_hold = DEFAULT_SDA_HOLD_FAST_PLUS,
|
|
.high_speed.sda_hold = DEFAULT_SDA_HOLD_HIGH,
|
|
},
|
|
};
|
|
|
|
static inline void i2c_mmio_write(uint32_t *base, uint8_t offset,
|
|
uint32_t data)
|
|
{
|
|
REG32((uint32_t) ((uint8_t *)base + offset)) = data;
|
|
}
|
|
|
|
static inline uint32_t i2c_mmio_read(uint32_t *base, uint8_t offset)
|
|
{
|
|
return REG32((uint32_t) ((uint8_t *)base + offset));
|
|
}
|
|
|
|
static inline uint8_t i2c_read_byte(uint32_t *addr, uint8_t reg,
|
|
uint8_t offset)
|
|
{
|
|
uint32_t ret = i2c_mmio_read(addr, reg) >> offset;
|
|
|
|
return ret & 0xff;
|
|
}
|
|
|
|
static void i2c_intr_switch(uint32_t *base, int mode)
|
|
{
|
|
switch (mode) {
|
|
|
|
case ENABLE_WRITE_INT:
|
|
i2c_mmio_write(base, IC_INTR_MASK, IC_INTR_WRITE_MASK_VAL);
|
|
break;
|
|
|
|
case ENABLE_READ_INT:
|
|
i2c_mmio_write(base, IC_INTR_MASK, IC_INTR_READ_MASK_VAL);
|
|
break;
|
|
|
|
case DISABLE_INT:
|
|
i2c_mmio_write(base, IC_INTR_MASK, 0);
|
|
/* clear interrupts: TX_ABORT
|
|
* Because the DW_apb_i2c's TX FIFO is forced into a
|
|
* flushed/reset state whenever a TX_ABRT event occurs, it
|
|
* is necessary for software to release the DW_apb_i2c from
|
|
* this state by reading the IC_CLR_TX_ABRT register before
|
|
* attempting to write into the TX FIFO
|
|
*/
|
|
i2c_mmio_read(base, IC_CLR_TX_ABRT);
|
|
/* STOP_DET */
|
|
i2c_mmio_read(base, IC_CLR_STOP_DET);
|
|
break;
|
|
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
static void i2c_init_transaction(struct i2c_context *ctx,
|
|
uint16_t slave_addr, uint8_t flags)
|
|
{
|
|
uint32_t con_value;
|
|
uint32_t *base = ctx->base;
|
|
struct i2c_bus_info *bus_info = &board_config[ctx->bus];
|
|
uint32_t clk_in_val = clk_in[bus_freq[ctx->bus]];
|
|
|
|
/* disable interrupts */
|
|
i2c_intr_switch(base, DISABLE_INT);
|
|
|
|
i2c_mmio_write(base, IC_ENABLE, IC_ENABLE_DISABLE);
|
|
i2c_mmio_write(base, IC_TAR, (slave_addr << IC_TAR_OFFSET) |
|
|
TAR_SPECIAL_VAL | IC_10BITADDR_MASTER_VAL);
|
|
|
|
/* set Clock SCL Count */
|
|
switch (ctx->speed) {
|
|
|
|
case I2C_SPEED_100KHZ:
|
|
i2c_mmio_write(base, IC_SS_SCL_HCNT,
|
|
NS_2_COUNTERS(bus_info->std_speed.hcnt,
|
|
clk_in_val));
|
|
i2c_mmio_write(base, IC_SS_SCL_LCNT,
|
|
NS_2_COUNTERS(bus_info->std_speed.lcnt,
|
|
clk_in_val));
|
|
i2c_mmio_write(base, IC_SDA_HOLD,
|
|
NS_2_COUNTERS(bus_info->std_speed.sda_hold,
|
|
clk_in_val));
|
|
break;
|
|
|
|
case I2C_SPEED_400KHZ:
|
|
i2c_mmio_write(base, IC_FS_SCL_HCNT,
|
|
NS_2_COUNTERS(bus_info->fast_speed.hcnt,
|
|
clk_in_val));
|
|
i2c_mmio_write(base, IC_FS_SCL_LCNT,
|
|
NS_2_COUNTERS(bus_info->fast_speed.lcnt,
|
|
clk_in_val));
|
|
i2c_mmio_write(base, IC_SDA_HOLD,
|
|
NS_2_COUNTERS(bus_info->fast_speed.sda_hold,
|
|
clk_in_val));
|
|
break;
|
|
|
|
case I2C_SPEED_1MHZ:
|
|
i2c_mmio_write(base, IC_FS_SCL_HCNT,
|
|
NS_2_COUNTERS(bus_info->fast_plus_speed.hcnt,
|
|
clk_in_val));
|
|
i2c_mmio_write(base, IC_FS_SCL_LCNT,
|
|
NS_2_COUNTERS(bus_info->fast_plus_speed.lcnt,
|
|
clk_in_val));
|
|
i2c_mmio_write(base, IC_SDA_HOLD,
|
|
NS_2_COUNTERS(bus_info->fast_plus_speed.sda_hold,
|
|
clk_in_val));
|
|
break;
|
|
|
|
case I2C_SPEED_3M4HZ:
|
|
i2c_mmio_write(base, IC_HS_SCL_HCNT,
|
|
NS_2_COUNTERS(bus_info->high_speed.hcnt,
|
|
clk_in_val));
|
|
i2c_mmio_write(base, IC_HS_SCL_LCNT,
|
|
NS_2_COUNTERS(bus_info->high_speed.lcnt,
|
|
clk_in_val));
|
|
i2c_mmio_write(base, IC_SDA_HOLD,
|
|
NS_2_COUNTERS(bus_info->high_speed.sda_hold,
|
|
clk_in_val));
|
|
|
|
i2c_mmio_write(base, IC_FS_SCL_HCNT,
|
|
NS_2_COUNTERS(bus_info->fast_speed.hcnt,
|
|
clk_in_val));
|
|
i2c_mmio_write(base, IC_FS_SCL_LCNT,
|
|
NS_2_COUNTERS(bus_info->fast_speed.lcnt,
|
|
clk_in_val));
|
|
break;
|
|
|
|
default:
|
|
break;
|
|
}
|
|
|
|
/* in SPT HW we need to sync between I2C clock and data signals */
|
|
con_value = i2c_mmio_read(base, IC_CON);
|
|
|
|
if (flags != 0)
|
|
con_value |= IC_RESTART_EN_VAL;
|
|
else
|
|
con_value &= ~IC_RESTART_EN_VAL;
|
|
|
|
i2c_mmio_write(base, IC_CON, con_value);
|
|
i2c_mmio_write(base, IC_FS_SPKLEN, spkln[bus_freq[ctx->bus]]);
|
|
i2c_mmio_write(base, IC_HS_SPKLEN, spkln[bus_freq[ctx->bus]]);
|
|
i2c_mmio_write(base, IC_ENABLE, IC_ENABLE_ENABLE);
|
|
}
|
|
|
|
static void i2c_write_buffer(uint32_t *base, uint8_t len,
|
|
const uint8_t *buffer, ssize_t *cur_index,
|
|
ssize_t total_len)
|
|
{
|
|
int i;
|
|
uint16_t out;
|
|
|
|
for (i = 0; i < len; i++) {
|
|
|
|
++(*cur_index);
|
|
out = (buffer[i] << DATA_CMD_DAT_OFFSET) | DATA_CMD_WRITE_VAL;
|
|
|
|
/* if Write ONLY and Last byte */
|
|
if (*cur_index == total_len) {
|
|
out |= DATA_CMD_STOP_VAL;
|
|
}
|
|
|
|
i2c_mmio_write(base, IC_DATA_CMD, out);
|
|
}
|
|
}
|
|
|
|
static void i2c_write_read_commands(uint32_t *base, uint8_t len, int more_data,
|
|
unsigned restart_flag)
|
|
{
|
|
/* this routine just set RX FIFO's control bit(s),
|
|
* READ command or RESTART */
|
|
int i;
|
|
uint32_t data_cmd;
|
|
|
|
for (i = 0; i < len; i++) {
|
|
data_cmd = DATA_CMD_READ_VAL;
|
|
|
|
if ((i == 0) && restart_flag)
|
|
/* if restart for first byte */
|
|
data_cmd |= DATA_CMD_RESTART_VAL;
|
|
|
|
/* if last byte & less than FIFO size
|
|
* or only one byte to read */
|
|
if (i == (len - 1) && !more_data)
|
|
data_cmd |= DATA_CMD_STOP_VAL;
|
|
|
|
i2c_mmio_write(base, IC_DATA_CMD, data_cmd);
|
|
}
|
|
}
|
|
|
|
int chip_i2c_xfer(const int port, const uint16_t slave_addr_flags,
|
|
const uint8_t *out, int out_size,
|
|
uint8_t *in, int in_size, int flags)
|
|
{
|
|
int i;
|
|
ssize_t total_len;
|
|
uint64_t expire_ts;
|
|
struct i2c_context *ctx;
|
|
ssize_t curr_index = 0;
|
|
uint16_t addr = I2C_GET_ADDR(slave_addr_flags);
|
|
int begin_indx;
|
|
uint8_t repeat_start = 0;
|
|
|
|
if (out_size == 0 && in_size == 0)
|
|
return EC_SUCCESS;
|
|
|
|
if (port < 0 || port >= ISH_I2C_PORT_COUNT)
|
|
return EC_ERROR_INVAL;
|
|
|
|
/* Check for reserved I2C addresses, pg. 74 in DW_apb_i2c.pdf
|
|
* Address cannot be any of the reserved address locations
|
|
*/
|
|
if (addr < I2C_FIRST_VALID_ADDR || addr > I2C_LAST_VALID_ADDR)
|
|
return EC_ERROR_INVAL;
|
|
|
|
/* assume that if both out_size and in_size are not zero,
|
|
* then, it is 'repeated Start' condition. */
|
|
if (in_size != 0 && out_size != 0)
|
|
repeat_start = 1;
|
|
|
|
ctx = &i2c_ctxs[port];
|
|
ctx->error_flag = 0;
|
|
ctx->wait_task_id = task_get_current();
|
|
|
|
total_len = in_size + out_size;
|
|
|
|
i2c_init_transaction(ctx, addr, repeat_start);
|
|
|
|
/* Write W data */
|
|
if (out_size)
|
|
i2c_write_buffer(ctx->base, out_size, out,
|
|
&curr_index, total_len);
|
|
|
|
/* Wait here until Tx is completed so that FIFO becomes empty.
|
|
* This is optimized for smaller Tx data size.
|
|
* If need to write big data ( > ISH_I2C_FIFO_SIZE ),
|
|
* it is better to use Tx FIFO threshold interrupt(as in Rx) for
|
|
* better CPU usuage.
|
|
* */
|
|
expire_ts = __hw_clock_source_read() + I2C_TX_FLUSH_TIMEOUT_USEC;
|
|
if (in_size > (ISH_I2C_FIFO_SIZE - out_size)) {
|
|
|
|
while ((i2c_mmio_read(ctx->base, IC_STATUS) &
|
|
BIT(IC_STATUS_TFE)) == 0) {
|
|
|
|
if (__hw_clock_source_read() >= expire_ts) {
|
|
ctx->error_flag = 1;
|
|
break;
|
|
}
|
|
CPU_RELAX();
|
|
}
|
|
}
|
|
|
|
begin_indx = 0;
|
|
while (in_size) {
|
|
int rd_size; /* read size for on i2c transaction */
|
|
|
|
/*
|
|
* check if in_size > ISH_I2C_FIFO_SIZE, then try to read
|
|
* FIFO_SIZE each time.
|
|
*/
|
|
if (in_size > ISH_I2C_FIFO_SIZE) {
|
|
rd_size = ISH_I2C_FIFO_SIZE;
|
|
in_size -= ISH_I2C_FIFO_SIZE;
|
|
} else {
|
|
rd_size = in_size;
|
|
in_size = 0;
|
|
}
|
|
/* Set rx_threshold */
|
|
i2c_mmio_write(ctx->base, IC_RX_TL, rd_size - 1);
|
|
|
|
i2c_intr_switch(ctx->base, ENABLE_READ_INT);
|
|
|
|
/*
|
|
* RESTART only once for entire i2c transaction.
|
|
* assume that if both out_size and in_size are not zero,
|
|
* then, it is 'repeated Start' condition.
|
|
* set R commands bit, start to read
|
|
*/
|
|
i2c_write_read_commands(ctx->base, rd_size, in_size,
|
|
(begin_indx == 0) && (repeat_start != 0));
|
|
|
|
|
|
/* need timeout in case no ACK from slave */
|
|
task_wait_event_mask(TASK_EVENT_I2C_IDLE, 2*MSEC);
|
|
|
|
if (ctx->interrupts & M_TX_ABRT) {
|
|
ctx->error_flag = 1;
|
|
break; /* when bus abort, no more reading !*/
|
|
}
|
|
|
|
/* read data */
|
|
for (i = begin_indx; i < begin_indx + rd_size; i++)
|
|
in[i] = i2c_read_byte(ctx->base,
|
|
IC_DATA_CMD, 0);
|
|
|
|
begin_indx += rd_size;
|
|
} /* while (in_size) */
|
|
|
|
ctx->reason = 0;
|
|
ctx->interrupts = 0;
|
|
|
|
/* do not disable device before master is idle */
|
|
expire_ts = __hw_clock_source_read() + I2C_TSC_TIMEOUT;
|
|
|
|
while ((i2c_mmio_read(ctx->base, IC_STATUS) &
|
|
(BIT(IC_STATUS_MASTER_ACTIVITY) | BIT(IC_STATUS_TFE))) !=
|
|
BIT(IC_STATUS_TFE)) {
|
|
|
|
if (__hw_clock_source_read() >= expire_ts) {
|
|
ctx->error_flag = 1;
|
|
break;
|
|
}
|
|
}
|
|
|
|
i2c_intr_switch(ctx->base, DISABLE_INT);
|
|
i2c_mmio_write(ctx->base, IC_ENABLE, IC_ENABLE_DISABLE);
|
|
|
|
if (ctx->error_flag)
|
|
return EC_ERROR_INVAL;
|
|
|
|
return EC_SUCCESS;
|
|
}
|
|
|
|
static void i2c_interrupt_handler(struct i2c_context *ctx)
|
|
{
|
|
uint32_t raw_intr;
|
|
|
|
if (IS_ENABLED(INTR_DEBUG))
|
|
raw_intr = 0x0000FFFF & i2c_mmio_read(ctx->base,
|
|
IC_RAW_INTR_STAT);
|
|
|
|
/* check interrupts */
|
|
ctx->interrupts = i2c_mmio_read(ctx->base, IC_INTR_STAT);
|
|
ctx->reason = (uint16_t) i2c_mmio_read(ctx->base, IC_TX_ABRT_SOURCE);
|
|
|
|
if (IS_ENABLED(INTR_DEBUG))
|
|
CPRINTS("INTR_STAT = 0x%04x, TX_ABORT_SRC = 0x%04x, "
|
|
"RAW_INTR_STAT = 0x%04x",
|
|
ctx->interrupts, ctx->reason, raw_intr);
|
|
|
|
/* disable interrupts */
|
|
i2c_intr_switch(ctx->base, DISABLE_INT);
|
|
task_set_event(ctx->wait_task_id, TASK_EVENT_I2C_IDLE, 0);
|
|
}
|
|
|
|
static void i2c_isr_bus0(void)
|
|
{
|
|
i2c_interrupt_handler(&i2c_ctxs[0]);
|
|
}
|
|
DECLARE_IRQ(ISH_I2C0_IRQ, i2c_isr_bus0);
|
|
|
|
static void i2c_isr_bus1(void)
|
|
{
|
|
i2c_interrupt_handler(&i2c_ctxs[1]);
|
|
}
|
|
DECLARE_IRQ(ISH_I2C1_IRQ, i2c_isr_bus1);
|
|
|
|
static void i2c_isr_bus2(void)
|
|
{
|
|
i2c_interrupt_handler(&i2c_ctxs[2]);
|
|
}
|
|
DECLARE_IRQ(ISH_I2C2_IRQ, i2c_isr_bus2);
|
|
|
|
static void i2c_config_speed(struct i2c_context *ctx, int kbps)
|
|
{
|
|
|
|
if (kbps > 1000)
|
|
ctx->speed = I2C_SPEED_3M4HZ;
|
|
else if (kbps > 400)
|
|
ctx->speed = I2C_SPEED_1MHZ;
|
|
else if (kbps > 100)
|
|
ctx->speed = I2C_SPEED_400KHZ;
|
|
else
|
|
ctx->speed = I2C_SPEED_100KHZ;
|
|
|
|
}
|
|
|
|
static void i2c_init_hardware(struct i2c_context *ctx)
|
|
{
|
|
static const uint8_t speed_val_arr[] = {
|
|
[I2C_SPEED_100KHZ] = STD_SPEED_VAL,
|
|
[I2C_SPEED_400KHZ] = FAST_SPEED_VAL,
|
|
[I2C_SPEED_1MHZ] = FAST_SPEED_VAL,
|
|
[I2C_SPEED_3M4HZ] = HIGH_SPEED_VAL,
|
|
};
|
|
|
|
uint32_t *base = ctx->base;
|
|
|
|
/* disable interrupts */
|
|
i2c_intr_switch(base, DISABLE_INT);
|
|
i2c_mmio_write(base, IC_ENABLE, IC_ENABLE_DISABLE);
|
|
i2c_mmio_write(base, IC_CON, (MASTER_MODE_VAL
|
|
| speed_val_arr[ctx->speed]
|
|
| IC_RESTART_EN_VAL
|
|
| IC_SLAVE_DISABLE_VAL));
|
|
|
|
i2c_mmio_write(base, IC_FS_SPKLEN, spkln[bus_freq[ctx->bus]]);
|
|
i2c_mmio_write(base, IC_HS_SPKLEN, spkln[bus_freq[ctx->bus]]);
|
|
|
|
/* get RX_FIFO and TX_FIFO depth */
|
|
ctx->max_rx_depth = i2c_read_byte(base, IC_COMP_PARAM_1,
|
|
RX_BUFFER_DEPTH_OFFSET) + 1;
|
|
ctx->max_tx_depth = i2c_read_byte(base, IC_COMP_PARAM_1,
|
|
TX_BUFFER_DEPTH_OFFSET) + 1;
|
|
}
|
|
|
|
static void i2c_initial_board_config(struct i2c_context *ctx)
|
|
{
|
|
uint8_t freq = bus_freq[ctx->bus];
|
|
struct i2c_bus_info *bus_info = &board_config[ctx->bus];
|
|
|
|
bus_info->std_speed.hcnt = default_hcnt_scl_100[freq];
|
|
bus_info->std_speed.lcnt = default_lcnt_scl_100[freq];
|
|
|
|
bus_info->fast_speed.hcnt = default_hcnt_scl_400[freq];
|
|
bus_info->fast_speed.lcnt = default_lcnt_scl_400[freq];
|
|
|
|
bus_info->fast_plus_speed.hcnt = default_hcnt_scl_1000[freq];
|
|
bus_info->fast_plus_speed.lcnt = default_lcnt_scl_1000[freq];
|
|
|
|
bus_info->high_speed.hcnt = default_hcnt_scl_hs[freq];
|
|
bus_info->high_speed.lcnt = default_lcnt_scl_hs[freq];
|
|
}
|
|
|
|
static void i2c_init(void)
|
|
{
|
|
int i;
|
|
|
|
for (i = 0; i < i2c_ports_used; i++) {
|
|
int port = i2c_ports[i].port;
|
|
i2c_initial_board_config(&i2c_ctxs[port]);
|
|
/* Config speed from i2c_ports[] defined in board.c */
|
|
i2c_config_speed(&i2c_ctxs[port], i2c_ports[i].kbps);
|
|
i2c_init_hardware(&i2c_ctxs[port]);
|
|
|
|
task_enable_irq((&i2c_ctxs[port])->int_pin);
|
|
}
|
|
|
|
CPRINTS("Done i2c_init");
|
|
}
|
|
DECLARE_HOOK(HOOK_INIT, i2c_init, HOOK_PRIO_INIT_I2C);
|