mirror of
https://git.savannah.gnu.org/git/gnuboot.git
synced 2025-01-06 16:27:40 +01:00
Denis 'GNUtoo' Carikli
6e5e4f3421
Before being merged with the commitdc6e1f32c1("Import website-build to build the GNU Boot website."), website-build was a separate git repository. And so, even after the merge, until the commit20d122e94a("website-build: use website from local git repository."), it still worked in the same way and still downloaded the website from git. This prevented merging the website and website-build directories together as the GNU Boot repository also needed to be a valid Untitled website repository as well. Now after this commit, the website is built from the same git tree, so we can simply adjust the build scripts to be able to move things around. In addition of making things more clear for contributors, it also simplify the migration to haunt as with haunt we typically have the haunt.cfg (and the autotools build code if needed) code in the top directory and the markdown files in a subdirectory. Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org> Acked-by: Adrien 'neox' Bourmault <neox@gnu.org>
224 lines
8.7 KiB
Markdown
224 lines
8.7 KiB
Markdown
---
|
|
title: ASUS Chromebook C201 installation guide
|
|
x-unreviewed: true
|
|
...
|
|
|
|
**Libreboot 20160907 only. This board was dropped in subsequent releases, but
|
|
may be added again in the future.**
|
|
|
|
**This documentation is retained from Libreboot 20160907, but it may also be
|
|
prudent to check documentation from Libreboot 20160907 itself. It is included
|
|
in the source code archive, for that release.**
|
|
|
|
The version of Depthcharge used here is very old, from 2016, and support for
|
|
this laptop was dropped in recent releases. It will be re-added at a later
|
|
date. If you wish to use Libreboot on this board, right now you must install
|
|
Libreboot 20160907. This page has been retained on libreboot.srht.site for now, but
|
|
you should refer to the documentation provided in the Libreboot 20160907
|
|
release if you want to learn more. NOTE: in that release, the documentation is
|
|
written in raw HTML, because the Markdown-based static site generator used on
|
|
libreboot.srht.site had not yet been written at that point.
|
|
|
|
These instructions are for installing Libreboot to the ASUS Chromebook
|
|
C201 (more known under a name [*veyron speedy*](../misc/codenames.md)).
|
|
Since the device ships with Coreboot, the installation
|
|
instructions are the same before and after flashing Libreboot for the
|
|
first time.
|
|
|
|
Look at the [list of ROM images](#rom) to see which image is compatible
|
|
with your device.
|
|
|
|
Libreboot can be installed internally from the device, with sufficient
|
|
privileges. The installation process requires using *Google's modified
|
|
version of flashrom*, that has support for reflashing the Chromebook's
|
|
SPI flash. Otherwise, flashing externally will work with the upstream
|
|
flashrom version.
|
|
|
|
*Google's modified version of flashrom* is free software and its
|
|
source code is made available by Google:
|
|
[flashrom](https://chromium.googlesource.com/chromiumos/third_party/flashrom/).\
|
|
It is not distributed along with Libreboot yet. However, it is
|
|
preinstalled on the device, with ChromeOS.
|
|
|
|
Installing Libreboot internally requires sufficient privileges on the system
|
|
installed on the device. When the device has ChromeOS installed (as it does
|
|
initially), it is necessary to gain root privileges in ChromeOS, to be able to
|
|
access a root shell.
|
|
|
|
Gaining root privileges on ChromeOS
|
|
--------------------------------
|
|
|
|
In order to gain root privileges on ChromeOS, developer mode has to be
|
|
enabled from the recovery mode screen and debugging features have to be
|
|
enabled in ChromeOS.
|
|
|
|
Instructions to access the [recovery mode
|
|
screen](../depthcharge/#recovery_mode_screen) and [enabling developer
|
|
mode](../depthcharge/#enabling_developer_mode) are available on the page
|
|
dedicated to [depthcharge](../depthcharge/).
|
|
|
|
Once developer mode is enabled, the device will boot to the [developer
|
|
mode screen](../depthcharge/#developer_mode_screen). ChromeOS can be
|
|
booted by waiting for 30 seconds (the delay is shortened in Libreboot)
|
|
or by pressing *Ctrl + D*
|
|
|
|
After the system has booted, root access can be enabled by clicking on
|
|
the *Enable debugging features* link. A confirmation dialog will ask
|
|
whether to proceed.\
|
|
After confirming by clicking *Proceed*, the device will reboot and ask
|
|
for the root password to set. Finally, the operation has to be confirmed
|
|
by clicking *Enable*.
|
|
|
|
After setting the root password, it becomes possible to log-in as root.
|
|
A tty prompt can be obtained by pressing *Ctrl + Alt + Next*. The
|
|
*Next* key is the one on the top left of the keyboard.
|
|
|
|
Preparing the device for the installation
|
|
Before installing Libreboot on the device, both its software and
|
|
hardware has to be prepared to allow the installation procedure and to
|
|
ensure that security features don't get in the way.
|
|
|
|
Configuring verified boot parameters
|
|
------------------------------------
|
|
|
|
It is recommended to have access to the [developer mode
|
|
screen](../depthcharge/#developer_mode_screen) and to [configure the
|
|
following verified boot
|
|
parameters](../depthcharge/#configuring_verified_boot_parameters):
|
|
|
|
- Kernels signature verification: *disabled*
|
|
- External media boot: *enabled*
|
|
|
|
Those changes can be reverted later, when the device is known to be in a
|
|
working state.
|
|
|
|
Removing the write protect screw
|
|
--------------------------------
|
|
|
|
Since part of the SPI flash is write-protected by a screw, it is
|
|
necessary to remove the screw to remove the write protection and allow
|
|
writing Libreboot to the *read-only* part of the flash.
|
|
|
|
To access the screw, the device has to be opened. There are 8 screws to
|
|
remove from the bottom of the device, as shown on the picture below. Two
|
|
are hidden under the top pads. After removing the screws, the keyboard
|
|
plastic part can be carefully detached from the rest. *Beware: there
|
|
are cables attached to it!* It is advised to flip the keyboard plastic
|
|
part over, as shown on the picture below. The write protect screw is
|
|
located next to the SPI flash chip, circled in red in the picture below.
|
|
It has to be removed.
|
|
|
|
[](../../img/c201/screws.jpg) [](../../img/c201/wp-screw.jpg)
|
|
|
|
The write protect screw can be put back in place later, when the device
|
|
is known to be in a working state.
|
|
|
|
Installing Libreboot to the SPI flash
|
|
=====================================
|
|
|
|
The SPI flash (that holds Libreboot) is divided into various partitions
|
|
that are used to implement parts of the CrOS security system. Libreboot
|
|
is installed in the *read-only* coreboot partition, that becomes
|
|
writable after removing the write-protect screw.
|
|
|
|
Installing Libreboot internally, from the device
|
|
------------------------------------------------
|
|
|
|
Before installing Libreboot to the SPI flash internally, the device has
|
|
to be reassembled.
|
|
|
|
All the files from the `veyron_speedy` release (or build) have to be
|
|
transferred to the device.
|
|
|
|
The following operations have to be executed with root privileges on the
|
|
device (e.g. using the `root` account). In addition, the
|
|
`cros-flash-replace` script has to be made executable:
|
|
|
|
chmod a+x cros-flash-replace
|
|
|
|
The SPI flash has to be read first:
|
|
|
|
flashrom -p host -r flash.img
|
|
|
|
*Note: it might be a good idea to copy the produced flash.img file at
|
|
this point and store it outside of the device for backup purposes.*
|
|
|
|
Then, the `cros-flash-replace` script has to be executed as such:
|
|
|
|
sudo bash ./cros-flash-replace flash.img coreboot ro-frid
|
|
|
|
If any error is shown, it is definitely a bad idea to go further than
|
|
this point.
|
|
|
|
The resulting flash image can then be flashed back:
|
|
|
|
flashrom -p host -w flash.img
|
|
|
|
You should also see within the output the following:
|
|
|
|
Verifying flash... VERIFIED.
|
|
|
|
Shut down. The device will now boot to Libreboot.
|
|
|
|
Installing Libreboot externally, with a SPI flash programmer
|
|
------------------------------------------------------------
|
|
|
|
Before installing Libreboot to the SPI flash internally, the device has
|
|
to be opened.
|
|
|
|
The SPI flash is located next to the write protect screw. Its layout is
|
|
indicated in the picture below. Note that it is not necessary to connect
|
|
`WP#` since after removing the screw it is pulled up weakly to 3v3. Before
|
|
writing to the chip externally, the battery has to be unplugged.
|
|
Battery connector is located under the heat spreader, that has to be
|
|
unscrewed from the rest of the case. It is located on
|
|
the right and has colorful cables, as shown on the picture below.
|
|
|
|
[](../../img/c201/spi-flash-layout.jpg)
|
|
[](../../img/c201/battery-connector.jpg)
|
|
|
|
All the files from the `veyron_speedy` release (or build) have to be
|
|
transferred to the host.
|
|
|
|
The following operations have to be executed with root privileges on the
|
|
host (e.g. using the `root` account). In addition, the
|
|
`cros-flash-replace` script has to be made executable:
|
|
|
|
chmod a+x cros-flash-replace
|
|
|
|
The SPI flash has to be read first (using the right spi programmer):
|
|
|
|
flashrom -p *programmer* -r flash.img
|
|
|
|
*Note: it might be a good idea to copy the produced flash.img file at
|
|
this point and store it outside of the device for backup purposes.*
|
|
|
|
Then, the `cros-flash-replace` script has to be executed as such:
|
|
|
|
./cros-flash-replace flash.img coreboot ro-frid
|
|
|
|
If any error is shown, it is definitely a bad idea to go further than
|
|
this point.
|
|
|
|
The resulting flash image can then be flashed back (using the right spi
|
|
programmer):
|
|
|
|
flashrom -p *programmer* -w flash.img
|
|
|
|
You should also see within the output the following:
|
|
|
|
Verifying flash... VERIFIED.
|
|
|
|
The device will now boot to Libreboot.
|
|
|
|
Installing Debian
|
|
---------------------
|
|
Debian is recommended for this device (which is on that list.
|
|
|
|
See <https://wiki.debian.org/InstallingDebianOn/Asus/C201>.
|
|
|
|
Also look at the HCL entry for operating systems (Debian, Devuan, Parabola):
|
|
<https://libreboot.srht.site/docs/hardware/c201.md>
|