7.5 KiB

Raw Blame History

title	x-toc-enable
Flashing the ThinkPad T400 externally	true

EHCI debug might not be needed. It has been reported that the docking station for this laptop has a serial port, so it might be possible to use that instead.

A note about CPUs

ThinkWiki has a list of CPUs for this system. The Core 2 Duo P8400, P8600 and P8700 are believed to work in libreboot.

T9600, T9500, T9550 and T9900 are all compatible, as reported by users.

Quad-core CPUs

Very likely to be compatible, but requires hardware modification. Based on info from German forum post about installing Core Quad CPU on T500 found in coreboot mailing list. Currently work in progress and no guide available.

A note about GPUs

Some models have an Intel GPU, while others have both an ATI and an Intel GPU; this is referred to as "switchable graphics". In the BIOS setup program for lenovobios, you can specify that the system will use one or the other (but not both).

Libreboot is known to work on systems with only the Intel GPU, using native graphics initialization. On systems with switchable graphics, the Intel GPU is used and the ATI GPU is disabled, so native graphics initialization works all the same.

CPU paste required

See #paste.

Flash chip size

Use this to find out:

flashrom -p internal

MAC address

Refer to mac_address.md.

How to flash externally

Refer to spi.md as a guide for external re-flashing.

The procedure

Remove all screws, placing them in the order that you removed them:

Remove those three screws then remove the rear bezel:

Remove the speakers:

Remove the wifi:

Remove this cable:

Unroute those antenna wires:

Remove the LCD assembly:

Disconnect the NVRAM battery:

Disconnect the fan:

Unscrew these:

Unscrew the heatsink, then lift it off:

Disconnect the power jack:

Loosen this:

Remove this:

Unscrew these:

Remove this:

Unscrew this:

Remove the motherboard (the cage is still attached) from the right hand side, then lift it out:

Remove these screws, placing the screws in the same layout and marking each screw hole (so that you know what ones to put the screws back into later):

Separate the motherboard:

Connect your programmer, then connect GND and 3.3V

A dedicated 3.3V PSU was used to create this guide, but at ATX PSU is also fine:

Of course, make sure to turn on your PSU:

Now, you should be ready to install libreboot.

Refer to the external flashing instructions here, and when you're done, re-assemble your laptop.

Thermal paste (IMPORTANT)

Because part of this procedure involved removing the heatsink, you will need to apply new paste. Arctic MX-4 is ok. You will also need isopropyl alcohol and an anti-static cloth to clean with.

When re-installing the heatsink, you must first clean off all old paste with the alcohol/cloth. Then apply new paste. Arctic MX-4 is also much better than the default paste used on these systems.

NOTE: the photo above is for illustration purposes only, and does not show how to properly apply the thermal paste. Other guides online detail the proper application procedure.

Memory

In DDR3 machines with Cantiga (GM45/GS45/PM45), northbridge requires sticks that will work as PC3-8500 (faster PC3/PC3L sticks can work as PC3-8500). Non-matching pairs may not work. Single module (meaning, one of the slots will be empty) will currently only work in slot 0.

NOTE: according to users reports, non matching pairs (e.g. 1+2 GiB) might work in some cases.

Make sure that the RAM you buy is the 2Rx8 configuration when buying 4GiB sticks (In other words: maximum of 2GiB per rank, 2 ranks per card).

This page might be useful for RAM compatibility info (note: coreboot raminit is different, so this page might be BS)

The following photo shows 8GiB (2x4GiB) of RAM installed: