The cr50 part on reef is connected to the SoC's UART lines. However,
when the tx signal is low it causes an interrupt to fire on cr50.
Therefore, keep the tx signal high in suspend state so that it doesn't
cause an interrupt storm on cr50 which prevents cr50 from sleeping.
BUG=chrome-os-partner:63283
BRANCH=reef
TEST=s0ix no longer causes interrupt storm on cr50. Power consumption
normal.
Change-Id: Idaeb8e4427c1cec651122de76a43daa15dc54d0f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18491
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Apply tuning for the PCH I2C buses on Eve based on rise/fall time
measurements that were done with a scope.
BUG=chrome-os-partner:59686
BRANCH=none
TEST=Manual testing on Eve P1 to verify that all devices on I2C
buses are still functional. Post-tuning measurement will be done
once a new firmware is released.
Change-Id: I3d70ff455a20ecda374d7e7fa6cd3ab15e7f2621
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18487
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
BUG=chrome-os-partner:62967
BRANCH=None
TEST=Verified that touchscreen works on power-on and after
suspend-resume as well.
Change-Id: Id674cbcc2d524a6ed2883bf9f0e9e076890f9a85
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18466
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Follow up to https://review.coreboot.org/#/c/18460/
Change-Id: Ic3aada2acf3051622698e10d2e764050e16480d5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18475
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
According to USB 2.0 Spec Table 7-7, the High-speed squelch
detection threshold Min 100mV and Max 150mV, and we set USB
2.0 PHY0 and PHY1 squelch detection threshold to 150mV by
default, so if the amplitude of differential voltage envelope
is < 150 mV, the USB 2.0 PHYs envelope detector will indicate
it as squelch.
On Kevin board, if we connect usb device with Samsung U2 cable,
we can see that the impedance of U2 cable is too big according
to the eye-diagram test report, and this cause serious signal
attenuation at the end of receiver, the amplitude of differential
voltage falls below 150mV.
This patch aims to reduce the PHY0 and PHY1 otg-ports squelch
detection threshold to 125mV (host-ports still use 150mV by
default), this is helpful to increase USB 2.0 PHY compatibility.
BRANCH=gru
BUG=chrome-os-partner:62320
TEST=Plug Samsung U2 cable + SEC P3 HDD 500GB/Galaxy S3 into
Type-C port, check if the USB device can be detected.
Change-Id: Ia0a2d354781c2ac757938409490f7c4eecdffe61
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7d74311c25762668386061234df0562f84b7203e
Original-Change-Id: Ib20772f8fc2484d34c69f5938818aaa81ded7ed8
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/431015
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Inno Park <ih.yoo.park@samsung.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18462
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
As David commented the "Bob and other follow-ons match Gru, Kevin should
be the special case here", and update the calculations value for gru/bob
board.
From the actual tests, some regulator voltage than the actual set of less
than 20mv on bob board. (e.g: little-cpus and Center-logic) Update the
{min, max} regulator voltage for Bob board. Make sure we get the accurate
voltage.
BUG=chrome-os-partner:61497
BRANCH=none
TEST=boot up Bob, measure the voltage for little cpu and C-logic.
Change-Id: Iad881b41d67708776bfb681487cf8cec8518064e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 25e133815f49018e7496c75077b8559c207350a4
Original-Change-Id: I3098c742c7ec355c88f45bd1d93f878a7976a6b4
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/424523
Original-Reviewed-by: David Schneider <dnschneid@chromium.org>
Original-Reviewed-by: Brian Norris <briannorris@chromium.org>
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/430403
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18460
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This patch adds the DPTF settings specfic to the mainboard and enables
the CPU and other thermal sensors as participant device for poppy.
It enables the DPTF flag in the device tree for poppy. It also includes
the DPTF specific ASL file in the main DSDT definition.
BUG=None
BRANCH=None
TEST=Built for poppy.
Change-Id: If44b01dd3c17fea06681ccf50e8e9f406e642e36
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/17926
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The children of Gru should share the benefits. In the real world, Bob can't
pass the eye diagram tests.
BUG=chrome-os-partner:62714
BRANCH=firmware-gru-8785.B
TEST=build coreboot
Change-Id: I2470bbc81acdaf2458d660dca5dc307cc3038f83
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d0cb3e718a7571f602a00c08a42019851634e7fd
Original-Change-Id: I0ccb48bb52eb770ccc9c8c265b07df46b0308dd3
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/440745
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/441468
Reviewed-on: https://review.coreboot.org/18461
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This is done to avoid any conflicts with same IRQ enums defined by other
drivers.
BUG=None
BRANCH=None
TEST=Compiles successfully
Change-Id: I539831d853286ca45f6c36c3812a6fa9602df24c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18444
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I538c28fb1bc412947ef9df947fa3f6a3312aeb4b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18322
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
poppy board uses Maxim 98927 speaker codec and Realtek RT5663
for headset. Select the apropriate NHLT blobs to be packaged in CBFS.
Also, generate the required ACPI NHLT table for codec and the supported
topology in poppy.
BUG=chrome-os-partner:62051
BRANCH=None
TEST=With the required driver support in kernel verify that
the Audio plays on on-board speakers and headset, recording
works from on-board mics and headset mics.
Change-Id: I98c65038b35fe99a661807de0766e6eac2c80eed
Signed-off-by: M Naveen <naveen.m@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/18214
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Wacom I2C driver does the same thing as I2C HID driver, other than
defining macros for Wacom HID. Instead of maintaining two separate
drivers providing the same functionality, update all wacom devices to
use generic I2C HID driver.
BUG=None
BRANCH=None
TEST=Verified that ACPI nodes for wacom devices are unchanged.
Change-Id: Ibb3226d1f3934f5c3c5d98b939756775d11b792c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18401
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Enable Fast-Plus speed for the touchscreen device so it can
be used at 1MHz instead of 400KHz.
BUG=chrome-os-partner:61277
TEST=manual testing on Eve P1, needs backported kernel patches
to actually make use of any I2C speed other than 400KHz
Change-Id: I3f44ff4a02a02a7b05e69ad54d4c6d60e5878393
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18397
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add the audio devices to Eve mainboard:
- Describe Maxim 98927 speaker amps and RT5663 headphone codec
in ACPI so they can be enumerated by the OS.
- Supply NHLT binaries for MAX98927, RT5663, and DMIC_4CH.
BUG=chrome-os-partner:61009
TEST=manual testing on Eve P1 with updated kernel to ensure that
both speakers and headset are functional. DMIC support is
is still being worked on and is not yet functional.
Change-Id: I5243e35d159a0ed15c6004e94ba5a50b28cff0a9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18398
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Since we are not using gpio regulators on reef anymore, remove the
selection from Kconfig as well.
BUG=None
BRANCH=None
TEST=Compiles successfully.
Change-Id: Iae7d88dec3ac476d65b292f97a6ba3add71ce07a
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18399
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Move code common code from each variant's mainboard.asl into
common ACPI code for all variants (like google/auron). This also
adds the _PRW method for the LID0 device for falco and peppy, which
omitted the function when they were originally upstreamed.
See Chromium commit c8b41f7, falco: Add _PRW for LID0 ACPI Device
Change-Id: I7f5129340249a986f5996af37c01ccbde8d374e8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18368
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Apply the measured rise and fall times for I2C bus 1 on Eve
so it can be tuned properly for 400KHz operation.
BUG=chrome-os-partner:63020
TEST=verify I2C1 bus speed with a scope
Change-Id: I32b5aa460ea35aadca7f3d52324a64880764919f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18396
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently UART0 GPIOs are being put into native mode during FSP-S
stage, so have ramstage re-configure them back to regular GPIO mode.
GPP_C8 does not seem to be functioning properly when routed to the
APIC, possibly due to the UART0 being enabled even though it is unused,
which is required because UART0 is PCI 1e.0 and so must be present for
other 1e.x functions to be enumerated. Instead, use this pin as a GPIO
interrupt so it will be routed through the GPIO controller at IRQ 14.
GPP_C9 was inverted and was only working because the pin was being
re-configured in FSP-S.
Also export the reset gpio as a device property so it can be used by
the kernel driver, which will stop it from complaining at boot.
BUG=chrome-os-partner:61233
TEST=verify that the interrupt and device is functional in the OS
Change-Id: Iaf9efbf50a13a981c6a9bbd507475777837e9c12
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18395
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support for generating digitizer node in SSDT using wacom i2c
driver.
BUG=None
BRANCH=None
TEST=Verified that the node shows up in SSDT.
Change-Id: If7e1e2463778c2ff7263eff995def149457edcde
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18373
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Some variants need the internal pull resistor on GPIO_SSUS_40
set explicitly to pull down rather than disabling the pull,
in order for the ram-id to be read correctly via GPIO.
Correct this by adding a function to enable and set the internal pull
and define its use as needed in the board's variant.h.
Chromium source:
branch: firmware-gnawty-5216.239.B
/src/soc/intel/baytrail/baytrail/gpio.h#418
/src/mainboard/google/gnawty/romstage.c#60
Test: boot 4GB Candy board and observe correct RAM id, amount detected
Change-Id: I8823c27385f4422184b5afa57f6048f7ff2a25ab
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18309
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Poppy doesn't support 8042 keyboard. Select
NO_FADT_8042 to disable 8042 in FADT header.
Kernel will not try to access 8042 region
if 8042.FADT=0
BUG=chrome-os-partner:61858
TEST=Boot OS and verify FADT 8042 flag
Change-Id: I00182eb4b059d4d9f0705d349dc98651e3955f0d
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/18311
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update DPTF parameters based on thermal team test result.
1. Update TSR2 trigger points.
TSR2 passive point: 70, critical point: 90
2. Set PL2 Max to 15W.
BUG=chrome-os-partner:61383
BRANCH=reef
TEST=build, boot on snappy, and verified by thermal team
Change-Id: I8d01d6c1d7eabd359ceb131f3cd10965d4ac2c42
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18318
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Performance degradation seen with current PL1 throttling rate as 8
seconds for TSR1 sensor with Aquarium workload. After fine tuning PL1
throttling rate to 15 seconds, fps score improved.
BUG=chrome-os-partner:60038
BRANCH=reef
TEST=Built and tested on electro system
Change-Id: I5cdebb08e00f0f28b88f1c6b2b1cafaeb8cdb453
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/18317
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
There will be more follow-up changes.
BUG=chrome-os-partner:62377
BRANCH=None
TEST=emerge-scarlet coreboot libpayload
Change-Id: I9ca45598ff0ab12bf8063d16a86be564cf509390
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a020a9ba1228b15599e202972df0096f58b1b31c
Original-Change-Id: I4804239483f8b35bc3703aa62c2a8fd642e0234a
Original-Signed-off-by: philipchen <philipchen@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/433039
Original-Commit-Ready: Philip Chen <philipchen@chromium.org>
Original-Tested-by: Philip Chen <philipchen@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18296
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Eve is a convertible add support for sending Tablet mode switch
changes from EC to AP.
Change-Id: I35133ebc1439852d0ceb88d7d679b37356b0869d
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/18276
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The WAK_STS bit is not set in a wake from G3, so the check for this
bit needs to only be done when checking for a wake from S3.
This change correctly enables the keyboard backlight in wake from G3
and only does not enable it during a wake from S3.
BUG=chrome-os-partner:58666
TEST=Use Refresh+Power to issue hard reset and ensure that the keyboard
backlight turns on like it does when waking from S5. Also force enter
hibernate with Alt+VolumeUp+H and then power back up and ensure that
the keyboard backlight is enabled when booting.
Change-Id: I44045950e38aa5e5ae96a79385d604791852c7e6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18280
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When guado/rikku/tidus were rolled into jecht, an error was
made in set_power_led() as guado/rikku set the polarity
differently than tidus. Fix the power LED for guado/rikku
by setting the polarity correctly.
Test: boot guado/rikku and observe proper function of power LED
under S0, S3, and S5 power states.
Change-Id: I23072ac60bc9683776f748ca1326d98257c3c54f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18249
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reason for revert:
Pyro has two touchscreen sources: WACOM/ELAN.
It will not have both touchscreen IC in one system at the same time.
So the "probed" property of WACOM i2c device is mandatory to set for kernel
to know whether it exists before driver initializes it.
Otherwise in ELAN case, when driver fails to init WACOM i2c device, ACPI _OFF
will be invoked to set GPIO#152 low to cut off power.
BUG=chrome-os-partner:62371
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: I30f467bd8720d959686dc14f7877e6bc11ea6213
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18291
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change fixes the two sets of pins that were swapped in the
map of DQS signals from CPU to DRAM for channel 1.
Although this does not appear to have any impact to the system it
does result in different register values for DQS pin mapping that
are programmed inside FSP.
BUG=chrome-os-partner:58666
TEST=This fix was verified against the current schematic and using
FSP debug output.
Change-Id: I45b821071ba287493b3b13204b7f5b38e06eee75
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18279
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
same change as I49935e659bf67225d3f5db1b06acc2cd046dcd74
this is required for poppy board as well.
GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals
when doing GPIO-driven I2S. This needs to be high by default so
the DSP can drive these signals, instead of low where it is enabled
for GPIO-driven I2S and the DSP cannot drive these signals.
BUG=None
BRANCH=None
TEST=play test sound in OS over internal speaker
Change-Id: I1695e9198f8f78e9c5ad6df6c1ac073ac1762c6b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18282
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals
when doing GPIO-driven I2S. This needs to be high by default so
the DSP can drive these signals, instead of low where it is enabled
for GPIO-driven I2S and the DSP cannot drive these signals.
BUG=chrome-os-partner:58666
TEST=play test sound in OS over internal speaker
Change-Id: I49935e659bf67225d3f5db1b06acc2cd046dcd74
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18281
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch sets PL2 override value to 15W in RAPL registers.
BUG=chrome-os-partner:62110
BRANCH=reef
TEST=Apply new firmware to evaluate Octane benchmark score.
Change-Id: I51734051586753677129314b5273fb275c74f5d2
Signed-off-by: Harry Pan <harry.pan@intel.com>
Reviewed-on: https://review.coreboot.org/18283
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Add new ChromeOS devices banjo, candy, clapper, glimmer, gnawty,
heli, kip, orco, quawks, squawks, sumo, swanky, and winky using
their common reference board (rambi) as a base.
Chromium sources used:
firmware-banjo-5216.334.B 32ec493 [chromeos: vboot_loader: Set...]
firmware-candy-5216.310.B 519ff11 [baytrail: Preserve VbNv around...]
firmware-clapper-5216.199.B 80d55e3 [baytrail: add code for...]
firmware-glimmer-5216.198.B fae0770 [baytrail: add code for...]
firmware-gnawty-5216.239.B 952adb7 [Gnawty/Olay: Add 2nd source...]
firmware-heli-5216.392.B f1f3604 [helis: Lock ME / TXE section...]
firmware-kip-5216.227.B db3c5d9 [kip: update spd for for MT41K256M16*]
firmware-orco-5216.362.B 76f1651 [Orco: Adjust rx delay for norm.]
firmware-quawks-5216.204.B edb60c9 [Quawks: Update SPD data]
firmware-squawks-5216.152.B c6573dc [Squawks: Update SPD data]
firmware-sumo-5216.382.B c62b6f23 [Ninja, Sumo: Add SPD source...]
firmware-swanky-5216.238.B 233b2a7 [Swanky: update SPD table]
firmware-winky-5216.265.B ce91ffc [Add to support HT Micron...]
The same basic cleanup/changes are made here as with the initial BYT
variant commit:
- remove unused ACPI trackpad/touchscreen devices
- correct I2C addresses in SMBIOS entries
- clean up comment formatting
- remove ACPI device for unused light sensor
- switch I2C ACPI devices from edge to level triggered interrupts,
for better compatibility/functionality (and to be consistent
with other recently-upstreamed ChromeOS devices)
- Micron 2GB SPD file for kip with updated values renamed to distinguish
from same file used by other boards
Change-Id: Ic66f9b539afb5aff32c4c1a8563f6612f5a2927c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18164
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
That status isn't needed and making it non-static helps gcc 4.9.2 (or
any compiler that insists on "standard C" behaviour with global const
initializers)
Change-Id: Ib1fbd5213d262e653f31564b106095b4a28292f6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/18266
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Apollolake boards should use DMIC-4ch configuration in Kernel side and
use CaptureChannelMap in userspace to distinguish boards with different
number of DMIC's. So, NHLT DMIC 1-ch & 2-ch endpoint configuration will
not be required and hence removed.
BUG=chrome-os-partner:60827
TEST=Verify internal mic capture
TEST='arecord -Dhw:0,3 dmic_4ch.wav -f S16_LE -r 48000 -c 4 -d 10' works
Change-Id: Ibe81290906c9e379ae49e437648ee9cd6f123ff8
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/18252
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
EC sets the logic level based on outstanding wake events. When GPIO_22
is configured as a level triggered interrupt, the events are not
cleared from the interrupt handler. Hence, we'd just be re-signalling
over and over causing an interrupt storm upon lid open. So, GPIO_22
needs to be configured as EDGE_SINGLE instead of LEVEL.
BUG=chrome-os-partner:62458
TEST=Lid close/open. check CPU usage using top. It should
not show 70% CPU usage.
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Change-Id: I710a690578c6e5b63be34b7fbcb21c703ef56e3a
Reviewed-on: https://review.coreboot.org/18267
Tested-by: build bot (Jenkins)
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
1. For ELAN, export reset GPIO as well as PowerResource
2. For WCOM, export PowerResource
BUG=chrome-os-partner:62311, chrome-os-partner:60194,
chrome-os-partner:62371
BRANCH=reef
TEST=Verified that touchscreen works on pyro with WCOM device on
power-on as well as after suspend/resume.
Change-Id: I0306e24e19bf821cd3e08fdacc0d78b494c9a92f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18239
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Linux kernel expects that power management with ACPI should always be
handled using PowerResource. However, some kernel drivers (e.g. ELAN
touchscreen) check to see if reset gpio is passed in by the BIOS to
decide whether the device loses power in suspend. Thus, until the kernel
has a better way for drivers to query if device lost power in suspend,
we need to allow passing in of GPIOs via _CRS as well as exporting
PowerResource to control power to the device.
Update mainboards to export reset GPIO as well as PowerResource for
ELAN touchscreen device.
BUG=chrome-os-partner:62311,chrome-os-partner:60194
BRANCH=reef
TEST=Verified that touchscreen works on power-on as well as after
suspend-resume.
Change-Id: I3409689cf56bfddd321402ad5dda3fc8762e6bc6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18238
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
