Tested on hardware with the patch from r4398 and works fine as soon
as Linux boots (no VGA in FILO for some reason, will investigate).
In order to make the 'i810.vga' VGA blob from the vendor BIOS work
you have to make the check for PCI device ID mismatches non-fatal
(for now) in the src/devices/pci_rom.c file like this:
Index: src/devices/pci_rom.c
===================================================================
--- src/devices/pci_rom.c (Revision 4393)
+++ src/devices/pci_rom.c (Arbeitskopie)
@@ -87,7 +87,7 @@
if (dev->vendor != rom_data->vendor || dev->device != rom_data->device) {
printk_err("Device or Vendor ID mismatch Vendor %04x, Device %04x\n",
rom_data->vendor, rom_data->device);
- return NULL;
+ // return NULL;
}
printk_spew("PCI ROM Image, Class Code %04x%02x, Code Type %02x\n",
The reason is that the VGA blob thinks the proper VGA device ID is 0x7123
whereas it really is 0x7121 on hardware. There are multiple ways to work
around this (there have been many discussions in the past), we'll see which
method will be used in future...
Note: This has been tested against r4393 only for now to make sure there
are no problems because of the recent resource allocator changes, see
http://www.coreboot.org/pipermail/coreboot/2009-July/050486.html.
Tests with trunk will follow.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4399 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
At the same time also make the 82810 code handle 82810E.
- Set SMRAM register according to CONFIG_VIDEO_MB value:
- 512 means 512 KB
- 1 means 1 MB
- Every other value for CONFIG_VIDEO_MB (e.g. 0) disables VGA.
This is not very clean, changing CONFIG_VIDEO_MB to CONFIG_VIDEO_KB
in a future patch may be nicer.
- Set MISSC2 register bits as required per datasheet to make VGA work.
The code handles both 82810 and 82810E.
- northbridge.c: Add __pci_driver entry for the Intel 82810E.
Also:
- Rename PAM register #define to PAMR as per datasheet.
- Drop unused/commented code for now.
- Don't explicitly set GMCHCFG for now, the default works ok. We'll
have to figure out the proper/ideal settings later.
The code is based on a patch from Elia Yehuda <z4ziggy@gmail.com> but
has been modified quite a bit for correctness and minimalism.
Tested on hardware with a slightly modified MS-6178 target,
patches to enable onboard-VGA for MS-6178 will follow.
Signed-off-by: Elia Yehuda <z4ziggy@gmail.com>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4398 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Turn on Parallel Port and Floppy in Config.lb
Signed-off-by: Harald Gutmann <harald.gutmann@gmx.net>
Acked-by: Andreas B. Mundt <andi.mundt@web.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4396 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The major change is that the K8 registers don't get touched until the end of
resource allocation.
Fam10 code could be updated the same way.
Move VGA code before resource allocation but after device enumeration.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4395 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Major changes:
1. Separate resource allocation into:
A. Read Resources
B. Avoid fixed resources (constrain limits)
C. Allocate resources
D. Set resources
Usage notes:
Resources which have IORESOURCE_FIXED set in the flags constrain the placement
of other resources. All fixed resources will end up outside (above or below)
the allocated resources.
Domains usually start with base = 0 and limit = 2^address_bits - 1.
I've added an IOAPIC to all platforms so that the old limit of 0xfec00000 is
still there for resources. Some platforms may want to change that, but I didn't
want to break anyone's board.
Resources are allocated in a single block for memory and another for I/O.
Currently the resource allocator doesn't support holes.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4394 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
targets/supermicro/h8dmr/Config.lb and Config-abuild.lb.
Importantly, this also sets
default CONFIG_AP_CODE_IN_CAR=0
in
src/mainboard/supermicro/h8dmr/Options.lb
which is required to make this box boot since the changes that went in in
r4315.
At Myles' suggestion, this patch also sets
default CONFIG_USE_FAILOVER_IMAGE=0
default CONFIG_USE_FALLBACK_IMAGE=0
default CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
in src/mainboard/supermicro/h8dmr/Options.lb to simplify
targets/supermicro/h8dmr/Config.lb a bit further.
Build tested with abuild, boot tested on physical hardware.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4393 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Thanks to Thomas Jourdan <thomas.jourdan@gmail.com> for reporting it.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4391 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jon Harrison <bothlyn@blueyonder.co.uk>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4389 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot you can now do:
$ util/abuild/abuild -t foo/bar
instead of
$ util/abuild/abuild -t foo/bar $PWD
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4388 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
didn't build before, and it still doesn't)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4387 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Attached is the third revision of the CN400/EPIA-N(L) patch for CB V2.
Patch should work against r4381 (or later ?)
This version now boots all of the way through to attempting to launch a
payload (I'm trying FILO right now), where it falls over with exception
6 (invalid opcode)
The coreboot_table issue seems to have been automagically resolved by
the latest core files.
It may still be that the reason for the payload not starting is down to
some issue with the tables initialising, I'll look closer at that.
Signed-off-by: Jon Harrison <bothlyn@blueyonder.co.uk>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4386 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Coreboot used to take SYSTEM_TYPE as a lable to tell what the socket is.
This patch replaces (some of, not all) CONFIG_SYSTEM_TYPE with CONFIG_SOCKET_TYPE.
It also fix some compiling error in src/northbridge/amd/amdmct/mct/mctardk4.c
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4385 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Kconfig)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4384 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4382 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It's basically done with the following script and some manual fixup:
VARS=`grep ^define src/config/Options.lb | cut -f2 -d\ | grep -v ^CONFIG | grep -v ^COREBOOT |grep -v ^CC`
for VAR in $VARS; do
find . -name .svn -prune -o -type f -exec perl -pi -e "s/(^|[^0-9a-zA-Z_]+)$VAR($|[^0-9a-zA-Z_]+)/\1CONFIG_$VAR\2/g" {} \;
done
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4381 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add identification for X58 and ICH10R.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4380 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
confusion, after we had a grace period to get people to move over to the
new repository.
History stays available for the archaeologists and for ancient
checkouts (potentially with local changes). Use "svn diff" to get local
changes, and apply it to a newer tree (if you manage to apply it, that
is).
The new repository is available at:
svn://coreboot.org/flashrom/trunk
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4379 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4378 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
from 2.6.30 (?)
the new vmlinux with per_cpu and brk support will have more sections.
Elf file type is EXEC (Executable file)
Entry point 0x200000
There are 7 program headers, starting at offset 64
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000200000 0xffffffff80200000 0x0000000000200000
0x0000000000e46000 0x0000000000e46000 R E 200000
LOAD 0x0000000001046000 0xffffffff81046000 0x0000000001046000
0x00000000001406e0 0x00000000001406e0 RWE 200000
LOAD 0x0000000001200000 0xffffffffff600000 0x0000000001187000
0x0000000000000888 0x0000000000000888 RWE 200000
LOAD 0x0000000001388000 0xffffffff81188000 0x0000000001188000
0x000000000008a086 0x000000000008a086 RWE 200000
LOAD 0x0000000001600000 0x0000000000000000 0x0000000001213000
0x0000000000015e20 0x0000000000015e20 RWE 200000
LOAD 0x0000000001629000 0xffffffff81229000 0x0000000001229000
0x0000000000000000 0x0000000000208000 RWE 200000
NOTE 0x0000000000b3c7e8 0xffffffff80b3c7e8 0x0000000000b3c7e8
0x0000000000000024 0x0000000000000024 4
Section to Segment mapping:
Segment Sections...
00 .text .notes __ex_table .rodata __bug_table .pci_fixup .builtin_fw __ksymtab __ksymtab_gpl __ksymtab_strings __init_rodata __param
01 .data .init.rodata .data.cacheline_aligned .data.read_mostly
02 .vsyscall_0 .vsyscall_fn .vsyscall_gtod_data .vsyscall_1 .vsyscall_2 .vgetcpu_mode .jiffies
03 .data.init_task .smp_locks .init.text .init.data .init.setup .initcall.init .con_initcall.init .x86_cpu_dev.init .altinstructions .altinstr_replacement .exit.text .init.ramfs
04 .data.percpu
05 .bss .brk
06 .notes
So need to increase NR_SECTIONS.
also fix one typo about phys address mask.
Peter says: A similar fix was also implemented by Maciej Pijanka, so let's
commit this now, eh.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4377 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Note that this board is nowhere near usable, further patches will follow
and hopefully get this into buildable and usable shape.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4376 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
some software wants to do an LDN access (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4374 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cbfstool-clean target to the Makefile.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4371 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
didn't look into it enough to know why fssize is 32 bytes larger than the
offset. There may be another bug here. Maybe something with the CBFS header
not being included or excluded from the calculation?
Anyway, this patch fixes it for all cases size > 32.
I also changed the error message so that it doesn't look like the ROM is full
just because it can't find room for a file.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4370 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested on hardware by Andrew Morgan <ziltro@ziltro.com>, boots
Linux fine. Detailed status at:
http://www.coreboot.org/Soyo_SY-6BA_Plus_III
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Andrew Morgan <ziltro@ziltro.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4369 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Its used for Name and Scope and Processor now. As bonus, it allows to
create a multi name paths too. Like Scope(\ALL.YOUR.BASE).
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4368 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4366 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, enable HIGH_TABLES support for this board.
The HIGH_TABLES failed with:
No matching ram area found for range:
[0x00000000000f0000, 0x0000000000100000)
Ram areas
[0x0000000000000000, 0x0000000000001000) Reserved
[0x0000000000001000, 0x00000000000a0000) RAM
[0x0000000000100000, 0x000000000fff0000) RAM
[0x000000000fff0000, 0x0000000010000000) Reserved
SELFBOOT RETURNED!
Boot failed.
The fix was to change northbridge.c as follows:
- ram_resource(dev, idx++, 1024, tolmk - 1024);
+ ram_resource(dev, idx++, 768, tolmk - 768);
This is build-tested and tested on hardware by me. It boots fine,
for instace with SeaBIOS and the standard GRUB1 from my disk.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4365 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add initial ACPI support for M57SLI.
Activates/Enables:
* native Coreboot ACPI for M57SLI
* Soft-Power-Off
* PowerNow!
* High Precision Event Timer
* Windows booting with ACPI support
Signed-off-by: Harald Gutmann <harald.gutmann@gmx.net>
Acked-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4364 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
[base address] parameter is supplied on the command line... This patch fixes
random segfaults when using 'cbfstool add'.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4363 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
updating the passed value to the next link offset even when it was on the
requested link (cap_count).
Maximilian also found a bug where the linktype was still getting attributes
even when it wasn't initialized.
This should fix the HT problems for Fam10 C2. There are still issues with the
microcode which need to be resolved.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4358 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ways superior to v3, while lacking its completeness. But, one nice
thing: no more included .S or .c files. It's all separate compilation.
That should allow our Makefiles to work much better.
Note that the current non-CAR implementation is the default and
continues to work (tested FILO boot to Linux on both CAR and non-CAR).
Index: src/mainboard/emulation/qemu-x86/Config.lb
Change this to be sensitive to USE_DCACHE_RAM. All settings etc. that
depend on this variable are grouped in one if, and the other parts
(romcc etc.) are in the else. This change is a model of how we should be
able to do other motherboards.
Index: src/mainboard/emulation/qemu-x86/Options.lb
add needed options.
Index: src/mainboard/emulation/qemu-x86/failover.c
remove code inclusion from this not-yet-used file.
Index: src/mainboard/emulation/qemu-x86/rom.c
This is the entry point for the rom-based code. Called stage1.c in v3.
Index: src/lib/Config.lb
change initobject to a .o from a .c; this fixed a build problem.
Index: src/pc80/serial.c
make uart_init non-static.
Index: src/pc80/Config.lb
add initobject
Index: src/arch/i386/init/entry.S
Entry point. Unify a bunch of files that were fiddly lttle includes. From v3.
Index: src/arch/i386/init/ldscript.ld
new file. The goal is to hang all init changes for CAR here, to minimize other changes to any
other ldscript. Besides, putting this in init makes sense; entry and car are manage init.
Index: src/arch/i386/init/car.S
generic i386 car code from v3.
Index: src/arch/i386/init/ldscript_fallback_cbfs.lb
Fix what looks like a bug: this was not including the init.text section.
Index: targets/emulation/qemu-x86/Config.lb
push up the console loglevel. qemu is for debugging so we might as well
get all the debugging we can.
Index: targets/emulation/qemu-x86/Config-car.lb
For CAR bullds.
Signed-off-by: Ronald G. minnich <rminnich@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4357 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Abuild tested and boot tested on s2895 and serengeti_cheetah.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4355 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
gets us through config, but it fails during build because the original patch
duplicated some files for VIA systems.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4354 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
if it is already in its correct location.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4353 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cbfs files at fixed addresses.
I call this transitional as the approach I am taking is to add
capability to cbfstool but not change code in a way that will break
existing usages. Later, once we're sure nothing has broken, we can start to
smooth the edges.
Right now, fixed address file are only supported via the add command.
There is one additional command syntax, so, example:
cbfstool add rom romstrap optionrom 0xffffd000
Will add the file to that fix location for a romstrap.
The assumption is that the ROM is based at the end of a 32-bit address
space. As you can see from the code, that assumption can easily be
over-ridden, if we ever need to, with a command option.
Here is one example output result.
rminnich@xcpu2:~/src/bios/coreboot-v2/util/cbfstool$ ./cbfstool x.cbf print
x.cbf: 1024 kB, bootblocksize 32768, romsize 1048576, offset 0x0
Alignment: 16 bytes
Name Offset Type Size
h 0x0 optionrom 251
0x130 free 917120
h3 0xdffe0 optionrom 251
0xe0110 free 97960
The way this is implemented is pretty simple. I introduce a new
operator, split, that splits an unallocated area into two unallocated
areas. Then, allocation merely becomes a matter of 0, 1, or 2 splits:
0 split -- the free area is the exact fit
1 splits -- need to split some off the front or back
2 splits -- need to split off BOTH the front and back
I think you'll be able to see what I've done. I call this transitional
because, in the end state, we only need one allocate function; for now
I've left two in, to make sure I don't break compatibilty.
Why I like this better than ldscript approach: I like having the
ROMSTRAP located by cbfs, not linker scripts. For one thing, it makes
romstrap visible as a first class object. I think I would have latched
onto a problem I was having much more quickly had I remembered the
ROMSTRAP. It gets lost in the linker scripts.
At this point, we should be able to start removing special ROMSTRAP location
code from linker scripts.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4351 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Uwe Hermann