Jens sent the first patch that added A49LF040A to flash.h and flashchips.c
using _jedec and _49lf040 functions.
An issue was found with probe_w29ee011() for the Winbond W29EE011, which
caused the A49LF040A to no longer respond to any commands.
Ward made a patch to disable probing by default for the W29EE011 following
some discussion. Using -c W29EE011 will make flashrom probe for the chip.
Peter did some more datasheet diving and found that the Pm49FL00x functions
suited this chip quite well because of the block locking registers in
A49LF040A, and finally tested PROBE READ ERASE WRITE to work on ALIX.3c3.
Ward confirmed that this works on alix.2c3 too.
Signed-off-by: Jens Kuehnel <coreboot@jens.kuehnel.org>
Signed-off-by: Ward Vandewege <ward@gnu.org>
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3368 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
When flash chip detection fails, it is still useful and possible to read the
flash chip contents. If no flash chip is found in normal probes and the
-f -r -c CHIPNAME options are given, a successful probe for the specified
chip is forced, and then flashrom reads the flash chip using either the read
function for the specified chip, or if there is none, a simple memcpy().
The patch also moves the global variable int force in flashrom.c into main()
and passes it as a parameter to layout.c:show_id(), which was the only other
function that used the variable. This is needed to avoid confusion with the
new parameter int force which is added to flashrom.c:probe_flash() and used
to force probe success for the chip named in char *chip_to_probe.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3367 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Uses the VT8237 ISA bridge with mainboard subsystem ID and Realtek 8139 with
mainboard subsystem ID for board detection.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Lyos Gemini Norezel <lyos.gemininorezel@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3366 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Thanks to Reinder for clean room reverse engineering and data sheet diving!
This board is autodetected because there are some good BioStar subsystem IDs.
Matching uses onboard VT6420 SATA RAID with subsystem BioStar 3206 and
onboard UniChrome Pro IGP graphics with subsystem BioStar 1202.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Lyos Gemini Norezel <lyos.gemininorezel@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3364 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
SST SST49LF160C is confirmed to work for PROBE READ ERASE WRITE, at least on
2 MCP55-based boards (gigabyte m57sli v1 and supermicro h8dmr).
On the m57sli board, it only works > 512K when booted into coreboot; the
proprietary bios seems to do something weird where it locks rom access down
to the first 512K of the chip.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3360 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I have tested MX25L4005, S25FL016A and W39V080A myself.
Thanks also to the following testers:
SST49LF008A Bernhard M. Wiedemann
W39V040B Dan Lenski
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3356 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested by me on actual hardware (all operations) - Artec Group DBE62 with SST 49LF004B
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3350 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- AMD Am29F040B
- SST SST39SF020A
- Winbond W29C020C
- Winbond W29EE011
- Winbond W49F002U
All of them tested by me on actual hardware (all operations).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3349 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix typos and inconsistencies.
- Drop duplicate line which tells us the chip name twice.
- Also print the chip vendor, not only the name.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3348 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested on actual hardware.
This patch add an ich_gpio_raise() function which can be re-used by other
board-specific funtions which need to raise GPIOs on ICHx southbridges.
This also fixes bug #7, see http://tracker.coreboot.org/trac/coreboot/ticket/7,
as it turned out the ICH2 (and other ICHx) code works fine.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3346 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch addresses different argument order of outX() calls,
FreeBSD-specific headers, difference in certain type names and system
interface names, and also FreeBSD-specific way of gaining IO port
access.
Signed-off-by: Andriy Gapon <avg@icyb.net.ua>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3344 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The PMC chips understand both LPC and FWH flash commands. When in FWH mode
(MSR_DIVIL_BALL_OPT(0x51400015) = 0x00000f7d on 5536 boards) the Block
Locking Registers by default lock the flash chip for write and erase - in
addition to any chipset write protection.
This patch adds unlock operations before Pm49FL004/2 write and erase, and
it includes an svn mv pm49fl004.c pm49fl00x.c
Thanks go to Nikolay for this patch.
Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com>
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Bari Ari <bari@onelabs.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3332 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
completely wrong. It was a straight cut'n'paste from SST 28SF040 code
and the person doing the cut'n'paste didn't even bother to check the
data sheet. The SST 39SF020 is completely incompatible with the 28SF040.
No need for replacement. According to the data sheet, standard JEDEC
commands will work and we have those commands in the tree already.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3331 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
of the SPIBAR differs. Add ICH8 support to the ICH9 code.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3327 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
IT8716F decodes any address to the attached SPI ROM.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3324 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flashchips.c, but the IDs in flash.h will make lookups easier if anybody
wants to add support for them.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3321 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Powerdown) SPI command to flashrom to identify older SPI chips which
can't handle JEDEC RDID. Since RES gives a one-byte identifier which is
shared among many different vendors and even different sizes, we want to
match RES as a last resort if RDID returns 0xff 0xff 0xff.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
This is a heavily reworked version of a patch by Fredrik Tolf, which was
Signed-off-by: Fredrik Tolf <fredrik@dolda2000.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3320 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
detected by JEDEC probe routines all have vendor IDs with correct
parity. Use a parity check as additional hint whether a vendor ID makes
sense.
Note: Device IDs have no parity requirements whatsoever.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3308 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch has no code changes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3302 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ICH9 SPI support. In theory, this patch has no behaviour changes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3301 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
by Harald Gutmann.
SST39VF040 has been confirmed to probe OK by misi e.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3300 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
series has the same IDs.
Add short AMIC vendor ID to flashrom.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3299 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This paves the way to have a fully generic generic_spi_command without
knowledge about any SPI controller.
The third step would be calling SPI controller functions via a function
pointer.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3296 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is a very early step toward cleaning up SPI code in flashrom.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3295 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Currently there is an ongoing technology migration from LPC/FWH to SPI chips.
For this reason some boards have multiple chips of different technologies
onboard. This patch makes flashrom probe for up to 3 chips and if more than
one chip is found flashrom exits, asking the user to specify -c.
[root@localhost src]# ./flashrom
...
Multiple flash chips were detected: SST49LF008A M25P16@ICH9
Please specify which chip to use with the -c <chipname> option.
[root@localhost src]#
Signed-off-by: Claus Gindhart <claus.gindhart@kontron.com>
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Claus Gindhart <claus.gindhart@kontron.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3291 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Two bits indicate OK and BAD for each operation PROBE READ ERASE WRITE.
8 bits out of 32 are in use now. No bits set means nothing has been tested.
For chips with at least one operation that is not tested or not working, the
user is asked to email a report to a special email adress so that the table
can be updated.
All chips are TEST_UNTESTED for now.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3277 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3275 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
devices, because they need an unlock command first.
For this reason, ST M50FLW support is moved to a
new HW support module, because any change in jedec.c
would bear the risk to cause problems with the already
supported devices.
It's already tested with ST M50FLW080A; the other
chips of this family i dont have available, so i couldnt
test it.
Signed-off-by: Claus Gindhart <claus.gindhart@kontron.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3274 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flashchips table. The read pointer was already checked properly.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3273 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
layout option, as well as areas, whose flash contents already contain the
desired data, will be skipped.
These ensures absolute data security of critical areas (BIOS boot block),
e.g. against a sudden power off or a CPU hangup during flashing. As a
nice side effect, it speeds up the flash process, if the BIOS to be flashed
is very similar to the version in flash.
Signed-off-by: Claus Gindhart <claus.gindhart@kontron.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3260 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Joseph Smith <joe@smittys.pointclark.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3221 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Support for the Winbond W39V080FA series of chips.
Support for flashing on the Kontron 986LCD-M board.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3166 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Support for flashing on the Kontron 986LCD-M board.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3165 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Jens Kuehnel