Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3854 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
incorrect license section.
- Remove the copyright listings and refer the reader to the source
files.
- Update the author list to those which have copyright messages in the
source files.
- Correct the license from GPL v2+ to (GPL v2, with some files under
later versions as well)
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3852 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flashchips.c over what's currently in flashrom HEAD.
The explicit initialization makes sure any future struct flashchip
reordering is not needed. (Except for the case where we need arrays
of some of the struct members.)
Signed-off-by: Stephan Guilloux <mailto:stephan.guilloux@free.fr>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3851 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
revF CPUs. The 100MHz/200MHz stepping is already handled in the FID setting
and doesn't need to be checked to set the fid_multiplier. The multiplier is
always 100.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: zheng bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3847 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
is no longer 0xA0 or 0xB0. It simply assumes that will never happen.
My 500 GB Seagate Barracuda ST3500820AS triggers that corner case on the
first init after poweron.
The current code hangs forever with my drive. Fix this by rerunning the
init sequence after SATA_BAR0+6 is no longer 0xA0 or 0xB0.
Add support for SATA port 2-4 (Primary Slave, Secondary Master,
Secondary Slave).
If only the 2nd SATA port is connected and the hardware acts strangely
(contrary to documentation), it will print the error message below and
continue anyway. The official AMD asm code behaves the same way.
SATA port 0 status = 0
No Primary Master SATA drive on Slot0
SATA port 1 status = 23
0x6=7f, 0x7=7f
drive no longer selected after 0 ms, retrying init
[8 repetitions]
0x6=7f, 0x7=7f
drive no longer selected after 0 ms, retrying init
Primary Slave device is not ready after 10 tries
Activate and improve debug messages for SPEW log level.
Fix some comments.
New log messages look like this:
PCI: 00:12.0 init
sata_bar0=3020
sata_bar1=3060
sata_bar2=3030
sata_bar3=3070
sata_bar4=3000
sata_bar5=fc309000
SATA port 0 status = 23
0x6=a0, 0x7=80
drive detection not yet completed, waiting...
0x6=a0, 0x7=80
drive detection not yet completed, waiting...
[... 281 repetitions ...]
0x6=0, 0x7=50
drive no longer selected after 2820 ms, retrying init
drive detection done after 0 ms
Primary Master device is ready after 2 tries
SATA port 1 status = 23
drive detection done after 0 ms
Primary Slave device is ready after 1 tries
SATA port 2 status = 0
No Secondary Master SATA drive on Slot2
SATA port 3 status = 0
No Secondary Slave SATA drive on Slot3
With this patch, my Asus M2A-VM boots into Linux without problems.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Zheng Bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3845 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The attached patch adds missing bits to ACPI to make Windows XP and Windows Vista happy.
The FADT bootarch flags
Blacklists MSI for this chipset (maybe not needed)
Adds modified amdk8_util.asl
Adds the SSDT table to chain of tables
Aligns the FACS correctly (this should be done for other boards)
Adds the _CRS method to Asus M2V-MX SE acpi DSDT.
Fixes the FACS table length.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3842 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-By: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3841 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The FADT bootarch flags
Blacklists MSI for this chipset (maybe not needed)
Adds modified amdk8_util.asl
Adds the SSDT table to chain of tables
Aligns the FACS correctly (this should be done for other boards)
Adds the _CRS method to Asus M2V-MX SE acpi DSDT.
Fixes the FACS table length.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3840 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The RS690 chipset has a problem where it will not work with 1 GHz HT
speed unless NB_CFG_Q_F1000_800 bit 0 is set.
Tested, works on my Asus M2A-VM with an 1 GHz HT capable processor.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Bao, Zheng says:
As a matter of fact, both 600Mhz and 1Ghz have their own specific
setting.
This patch has been tested on dbm690t which HT link works on 800Mhz.
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3839 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
initialization.
This patch has helped immensely to track down a bug in 690G ncHT init.
It depends on my earlier patch which enables CONFIG_USE_PRINTK_IN_CAR
for all boards using HT. Of course that means ROMCC is not an option
anymore for those boards, but I don't think that's a big problem.
Another way to solve this would be #defining printk_spew to nothing.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Marc says:
ROMCC doesn't make sense for k8 boards.
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3836 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Fix that by throwing an error instead.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3834 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
There seem to be at least two versions of the board out there, and the
subsystem IDs changed between the versions.
Patch successfully tested on hardware.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3833 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
debug code to src/northbridge/amd/amdk8/incoherent_ht.c.
However, printk is not available for all boards at that stage.
I have changed the following boards:
agami/aruma
arima/hdama
asus/a8n_e
broadcom/blast
ibm/e325
ibm/e326
iwill/dk8s2
iwill/dk8x
msi/ms7135
newisys/khepri
sunw/ultra40
tyan/s2850
tyan/s2875
tyan/s2880
tyan/s2881
tyan/s2882
tyan/s2885
tyan/s2891
tyan/s2892
tyan/s2895
tyan/s4880
tyan/s4882
abuild works fine for all of them.
agami/aruma needs a Config-abuild.lb which doesn't have fallback and
normal due to size problems.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3829 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
used for a SIR/FIR device.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ulf Jordan <jordan@chalmers.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3827 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
in the VT8237R, and a card interrupting at Pin-A on either PCI slot.
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3826 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
different ROM chip sizes (trivial, tested with 256 KB chip).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3825 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
implemented (It just prints "hard_reset not implemented. FIX ME!" This patch
defines HAVE_HARD_RESET 1 and adds a #warning hard_reset not implemented.
The net effect is that hard_reset prints something instead of just entering an
infinite loop.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3823 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
worked or not, but my board doesn't have COM1, and those function don't
support using COM2, so I've changed auto.c to use the fintek f71805f
functions, the fintek is the onboard super io. I also cleaned up a
whitespace issue and unused variable.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3821 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The device ID of 690G is 0x791E, while the ID of 690M and 690T is 0x791F
This fixes booting on 690G.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3816 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* rename ich_check_opcodes to ich_init_opcodes.
* let ich_init_opcodes do not need to access flashchip structure:
. move the definition of struct preop_opcode_pair to a better place
. remove preop_opcode_pairs from 'struct flashchip'
. modify ich_init_opcodes and generate_opcodes so that they do not access the flashchip structure
* call ich_init_opcodes during chipset enable. Now OPCODES generation mechanism works.
* fix a coding style mistake.
Signed-off-by: FENG yu ning <fengyuning1984@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3814 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
specific changes based on the DBM690T code.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3813 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
mainboard specific code. (And add a hook to allow other mainboards do
a similar thing if required)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3812 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
document verification against the data sheets.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Maggie Li <maggie.li@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3811 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This should hopefully make the "too few registers" error pop up less often.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3810 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
support the MX29LV040C.
MX29LV040C probe and read support tested by khetzal on IRC.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3809 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Peter Stuge