been used in the last few years, and the contents are available in
the README already anyway.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3134 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3132 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
tyan s2881 board, in preparation of supporting it in buildrom. Corresponding
changes for the other buildrom-supported boards were committed in r3092.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3130 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3129 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
No functional changes, only cosmetics. This is compile-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3128 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
'superiotool --help' already provide the same information (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Stefan Reinauer for coresystems GmbH in 2005, as confirmed on IRC.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3126 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
no VGA output from coreboot, even after the boot-rom was executed
properly (CONFIG_PCI_ROM_RUN) or no boot-rom execution with
CONFIG_VGA_ROM_RUN at all. According to the header file device.h, the
class field of struct device is '3 bytes: (base,sub,prog-if)'.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Acked-by: Torsten Duwe <duwe@lst.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3119 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
stop the CPU fan on the m57sli v1.1 (PLCC) entirely, which is less than
desirable. I did not notice before because my board ran fine for about 15
minutes before the CPU overheated.
Thankfully the board has a good failsafe mode - it just switches off when the
CPU gets too hot, without permanent damage.
I'm debugging this and plan to commit a proper fix later in the week.
This is not really trivial, but the tree is dangerous in the current state so
I'm self-acking.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3118 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
pnp-style configuration registers, using the new option -e/--extra-dump.
This patch only adds dumping of the Environmental Controller
configuration registers for the IT8716f chip.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
I (Carl-Daniel) checked the data sheets of the whole IT87[012] series
and although the environment controller is sometimes called fan
controller, the location of the register is the same for all models.
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3117 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
board.
This is done via the ec_init routine in a source file in the
mainboard/gigabyte/m57sli directory. A Config variable 'HAVE_FANCTL' has been
added to notify superio.c to get the ec_init externally.
I (Ward) have tested this on the PLCC and the SOIC/SPI version of this board.
It works.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3116 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
a compiler warning.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3115 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested on real hardware.
This is a trivial patch.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3114 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
working for now, and more work is needed for it to be fully dynamic. However,
just about any 128MB-512MB DIMM should work.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3113 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Don't enable pin0 for ioapic of io-4.
1. apic error in kernel for MB with mcp55+io55
2. some pcie-cards could have pci bridge there, so need to put entries
for device under them in mptable.
Signed-off-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3112 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3111 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also add a comment about NULL subsystem IDs leaving the board entry out
of auto-detection logic.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3110 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
undefined u8 type and the bitpos selection in currently unused
pnp_read_enable function.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3109 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch introduces virtual LDNs changes for W83627EHF driver. Not only LDN 7 and 9 are
changed, but also a SPI flash interface which has enable on bit1 and not bit0.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3108 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
device) and sets the chipset voltage from 1.6V to 1.5V.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3107 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
changed, but also a SPI flash interface which has enable on bit1 and not bit0.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3106 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
have GAME and MIDI portsenabled.
It has been tested with my board. It produces same results.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3105 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
mine W83627EHF.
This patch introduces a concept of virtual LDN. Each virtual LDN is unique, but
maps to original LDN and bit position in register 0x30.
VirtualLDN = origLDN[7:0] | bitpos[10:8]
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3104 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
specifying custom CFLAGS/LDFLAGS from the make command line like:
make CFLAGS="..." LDFLAGS="..."
I need to do this when building flashrom in a cross compiler environment
like buildroot for a foreign target.
Signed-off-by: Clark Rawlins <clark@bit63.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3102 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Remove the "enable write to flash" message, as the caller appears to
already report that.
- Move the 'modprobe msr' suggestions to the first lseek64 error handling, as
we get an error there already.
- Rename a perror string from "read" to "read msr", as we use the latter
already in this function for another read.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3101 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3100 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, move a big code comment to the top of enable_flash_cs5536().
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3098 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CS5536 that have the Boot ROM on NOR flash that is directly connected to
FLASH_CS3 (Boot Flash Chip Select).
We need to write enable it in the NORF_CTL MSR register for flashrom to
be able to write to it, including JEDEC probe commands.
This patch allows us to stop using AMD gx_utils.ko for BIOS flashing on
the DBE61.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3097 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Programmable Micro Corp (PMC) need this.
Both the serial and parallel flash JEDEC detection routines would
benefit from a parity/sanity check of the vendor ID. Will do this later.
Add support for the PMC Pm25LV family of SPI flash chips.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Chris Lingard <chris@stockwith.co.uk>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3091 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I think that since the directory specifies the architecture and the
board, it is redundant information to name it something else, and it
makes it more difficult to automate the build process (buildrom).
Signed-off-by: Myles Watson <myles@pel.cs.byu.edu>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3090 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
following mainboard files had identical Geode LX specific print_conf()
implementations:
mainboard/amd/db800/mainboard.c
mainboard/amd/norwich/mainboard.c
mainboard/digitallogic/msm800sev/mainboard.c
mainboard/pcengines/alix1c/mainboard.c
Move print_conf() to northbridge/amd/lx/northbridge.c where it belongs.
Add a copyright notice to mainboard/digitallogic/msm800sev/mainboard.c.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3089 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
LPC device of the MCP55 southbridge, thus enabling flashrom access to the SPI
interface of the IT8716 SIO chip.
Changes :
1) - increase MAX_RESOURCES to 24 in device.h -> this was needed because some
functions of a PNP device can have more than 12 resources (ex the GPIO function
of IT8716f), in which case one could have an "array overflow" inside the device
structure (yes gcc is stupid!..) and ultimately a disaster (fool pointer at
device init time..)
2) - define resource masks for the GPIO function in
src/superio/ite/it8716f/superio.c -> this is needed because otherwise the IO
ranges which are set into the LPC bridge of the SB are very strange (f.ex.:
0x800->0x7ff and so on..). Problem: the PNP_IO0 resource is not defined for the
GPIO function, thus we have to define a "fake" mask "{0,0}" to avoid mismatching
by the init code
3) - enable the flash SPI interface into
src/mainboard/gigabyte/m57sli/Config.lb (by enabling the corresponding resource
into the GPIO function). I know that this is problematic because not all m57sli
boards are SPI, but .. do anyone have a better idea how to handle this?..
Signed-off-by: Florentin Demetrescu <echelon@free.fr>
I (Ward) have verified your patch on a rev2 of this board (it works!) as well
as on a rev1 (plcc). It does not affect flashing on rev1 nor have any averse
side effects that I noticed, so I think this patch should go in.
Acked-by: Ward Vandewege <ward@gnu.org>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3088 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Uwe Hermann