- Enable Acoustic noise mitigation
- Set slow slew rate to fast/4 for VCCIA and VCCGT
- Disable fast slew rate for deep package C states for VCCIA and VCCGT
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: Ia344d9d939c3323bac82afdf25d5fff81081f9c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67380
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Lastbus is a bus debug tool. When the bus hangs, the bus transmission
information before resetting will be recorded.
The watchdog cannot clear it and it will be printed out for bus hanging
analysis.
TEST=build pass.
BUG=none
Signed-off-by: ot_zhenguo.li <ot_zhenguo.li@mediatek.corp-partner.google.com>
Change-Id: Iff39486dfad556a3104b2f2b6811c34c2ded6954
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67437
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
1. There are two power sources for CPU:
- Logic power (VPROC).
- SRAM power (VSRAM_PROC).
2. There is a constraint between VPROC and VSRAM_PROC:
- 0mV <= VSRAM_PROC - VPROC <= 250mV.
With software control, the constraint might not always hold. Therefore,
we enable hardware tracking from PMIC MT6366 to ensure the constraint
is met automatically.
BUG=b:236353282, b:241615706
TEST=meet the constrain correctly when adjusting the voltage.
Signed-off-by: Sen Chu <sen.chu@mediatek.corp-partner.google.com>
Change-Id: I6012c57e60c009f1d599b57aab1c2526ee789208
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67436
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TEST=Boot to OS on nivviks/nirwen and check that stylus GPIOs are
configured based on fw_config.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: Ibbe9f379abe10a741642e11d4833d3a53489693a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66929
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Config I2C high / low time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (400 kHz).
EE measured touchscreen/audio runs at 385.5/397.9kHz after tuning.
BUG=b:244403643
BRANCH=firmware-dedede-13606.B
TEST=Build and check after tuning I2C clock is under 400kHz
Change-Id: I7d9503e5f92295432e31f09ae791eaa18eac9d4d
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that the driver skips
initial probe during kernel boot and prevent privacy LED blink.
BUG=b:194979741
BRANCH=firmware-brya-14505.B
TEST=Build and boot skolas to OS. Verify entries in SSDT.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I3c32dd71ab454227b15913bda7f542230e5568db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Historically, ChromeOS devices have worked around the problem of OEMs
using several different parts for touchpads/touchscreens by using a
ChromeOS kernel-specific 'probed' flag (rejected by the upstream kernel)
to indicate that the device may or may not be present, and that the
driver should probe to confirm device presence.
Since c636142b, coreboot now supports detection for i2c devices at
runtime when creating the device entries for the ACPI/SSDT tables,
rendering the 'probed' flag obsolete for touchpads. Switch all touchpads
in the tree from using the 'probed' flag to the 'detect' flag.
Touchscreens require more involved power sequencing, which will be done
at some future time, after which they will switch over as well.
TEST: build/boot at least one variant for each baseboard in the tree.
Verify touchpad works under Linux and Windows. Verify only a single
touchpad device is present in the ACPI tables.
Change-Id: I47c6eed37eb34c044e27963532e544d3940a7c15
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67305
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The previous VBT binary was not properly configured, there were DP
display issues on some of the ports and resulted in hangs when FSP
debug was used. The updated VBT fixes all the issues.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I788240e36a9a90a5342ee9761f2c61ebf4caa9a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67426
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Expose configuration of Intel PAVP (Protected Audio-Video Path, a
digital rights protection/management (DRM) technology for multimedia
content) to Kconfig.
TEST=Able to boot Google/rex to ChromeOS.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I416346995d744990054c8e0c839ada82c84b7550
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67423
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Follow the Thermal_paramters_list-0902.xlsx to modify DPTF parameters
and fan table.
1. Modify CRT of TSR0 - TSR3 to 97.
2. Modify TCC offset to 6.
3. Update new fan table.
BUG=b:244657172
TEST=emerge-brask coreboot
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I751bc5442f64428c383034755cd5d74fbd0ea91e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67314
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Modify fan speed/duty table follow "Duty table.xlsx".
BUG=b:244262869
TEST=Boot to ChromeOS. Using SDV system, enter duty value, and then
system feedback fan speed.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Id5e885b96624d5fc31f1d42e3582c3ab01e08458
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
The Kinox fan speed/duty table has 20 elements so raise the
DPTF_MAX_FAN_PERF_STATES from 10 to 20.
BUG=b:244262869
TEST=Boot to ChromeOS. Using SDV system, enter duty value, and then
system feedback fan speed.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Iacd3ef0da926df5d174b215ab8ea4adc1a8b672e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67390
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
The PCIe WWAN module used on rex requires control over 4 signals to
successfully power it on. It is desirable to do this before passing
control to the payload, because the modem requires a ~10 seconds
initialization phase before it can be used.
The corrected sequence looks like:
1) Drive device into full reset and enable power in bootblock
2) Deassert FCPO in romstage, after power rails stabilize
3) Deassert WWAN_RST#, then WWAN_PERST# in ramstage
BUG=b:244077118
TEST=FM350 could be enumerated via lspci
Measured signals to check start-up Timing Sequence, tpr/ton1/ton2.
Tpr = 572mS
Ton1 = 6.3s
Ton2 = 6.3+4.17ms
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Change-Id: I6cda9348ef7f54efe5ba2358040596a1c2da1b13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67332
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable SRAM in devicetree so that resources are allocated properly
for it.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ibdd2ee455f5bf6cd95bba6bab8689da664bfcf54
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Use the BIT() macro instead of reinventing the wheel.
TEST=timeless builds are identical
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I873013feebd30c86290dda692c7b137d5f3c4729
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add the missing spaces to two log message, like the one below.
WARNING: Device PCI: 03:00.0 requests a BAR with34 bits of address space, which coreboot is notconfigured to hand out, truncating to 29 bits
Change-Id: If933d8fb0db5b58ff12f043cc73172a3f6ffc624
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Missing power limit setting for Alder-Lake-N 7W soc.
Document reference: 645548 and 646929
BUG=b:245440443
BRANCH=None
TEST=Build FW and test on nivviks board and there is no error
message "unknown SA ID: 0x4617, skipped power limits configuration."
Signed-off-by: Simon Yang <simon1.yang@intel.com>
Change-Id: Iefe17f5b574cc319fe9aad3850401a8aa8e31270
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
This area relates to storing of AP RO verification information.
CONFIG_VBOOT_GSCVD is enabled by default for TPM_GOOGLE_TI50 and
guybrush is using TPM_GOOGLE_CR50.
Signed-off-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Change-Id: I896b871bf2ac64e334514b979add9b8ac2c43945
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Harsha B R <harsha.b.r@intel.com>
Change the name of the CALIBRATION_REGION definitions used in two
separate locations. This conflict was causing an error for the
lint-001-no-global-config-in-romstage test.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If6734f2a7d9be669586ea350fb9979fcd422b591
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Currently, the "loading FSP-S" timestamp is added in fsp_silicon_init().
However, most Intel platforms actually load FSP-S earlier than this, in
soc_fsp_load(). So the timestamp is added in the wrong place.
Add the timestamp in fsps_load() instead, after the load_done early
return so that it will only be added for the first call.
Before:
949:finished CSE firmware sync 961,833 (17,998)
17:starting LZ4 decompress (ignore for x86) 1,018,328 (56,495)
18:finished LZ4 decompress (ignore for x86) 1,018,797 (469)
30:device enumeration 1,035,096 (16,298)
971:loading FSP-S 1,048,082 (12,986)
954:calling FspSiliconInit 1,049,331 (1,249)
After:
949:finished CSE firmware sync 959,355 (16,370)
971:loading FSP-S 978,139 (18,784)
17:starting LZ4 decompress (ignore for x86) 1,015,796 (37,656)
18:finished LZ4 decompress (ignore for x86) 1,016,271 (475)
30:device enumeration 1,032,567 (16,295)
954:calling FspSiliconInit 1,046,867 (14,300)
BUG=b:239769975
TEST="loading FSP-S" is added in the right place on nivviks (see above).
Change-Id: Ib26cf96ae97766333fe75ae44381d4f7c6cc7b61
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Having a CSE Lite SKU's firmware is not necessarily depending
on the underlying hardware nor on having ChromeOS installed as
already mentioned in commit f3419b29b7 ("soc/intel/common/cse:
Drop dependency on CHROMEOS for SOC_INTEL_CSE_LITE_SKU").
For example RVP Boards sometimes have a CSE LITE FW, if Chrome board
related stuff is tested, which doesn't necessarily imply a ChromeOS
being used. It is therefore changed to an option, which can be
changed in menuconfig.
Change-Id: I4da7feab881ae43528c9d852cc842ac93fa9c6de
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67078
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To test the linters, we want to invert the results so that any test that
passes shows up as a failure. This will allow us to verify that all of
the linters are working correctly.
This will be tested nightly as well as on changes to the lint tools.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ia8024c6ab0c91fd9f630f37dc802ed3bc6b4608c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Enable the APOB_HASH feature. This improves boot times by ~10ms.
BUG=b:193557430
TEST=boot to OS and verify boot time improvement
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I9628b67cd3206ffdbef23162c453dc183c69e5a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67377
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Comparing the APOB in RAM to flash takes a significant amount of time
(~11ms). Instead of comparing the entire APOB, use a fast hash function
and compare just that. Reading, hashing, and comparing the hash take
~70 microseconds.
BUG=b:193557430
TEST=compile and boot to OS in chausie with and without this option set
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I241968b115aaf41af63445410660bdd5199ceaba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Add xxhash functions. This is a very fast hash function, running at RAM
speed limits.
This code was adapted from the linux kernel with minor modifications to
make it fit in coreboot.
BUG=b:193557430
TEST=compile
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I8108af5ab14d8e6c6f5859bd36155c7d254e892c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
coreboot unit-tests framework requires tests to use
cb_run_group_tests() instead of cmocka_run_group_tests() for Jenkins
to work correctly. Wrapper ensures that each test has its own report
file and does not overwrite results of other tests.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Iead63cab0465f37b2da0c7b3ef256057e3a191a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67371
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This updates the SPD utility and generated SPDs for LP5X to use memory
type code 0x15 (LPDDR5X) instead of 0x13 (LPDDR5). This is done based on
Intel Tech Advisory Doc ID #616599 dated May 2022, page 15.
SPDs were regenerated with:
"util/spd_tools/bin/spd_gen spd/lp5/memory_parts.json lp5"
This only affects the SPDs for 2 memory parts for Intel SoCs and the
only board referencing these is rex.
BUG=b:242765117
TEST=inspected SPD hex dump
Change-Id: Iadb4688f1cb4265dab1dc7c242f0c301d5498b83
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
dptc_enable is being treated as a bool, so convert to explicitly be a
bool.
BRANCH=none
BUG=b:217911928
TEST=Build zork
TEST=Build guybrush
TEST=Build skyrim
Change-Id: I0e93d892b3b8016221812c8b9ec6c257dcf13ef5
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67188
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Due to layout restrictions on mc_ehl2, the SD-card interface is limited
to operate in DDR50 mode. The alternative modes SDR104 and SDR50 are not
supported. Limit the capabilities in the SD card controller to DDR50
mode only so that the SD card driver in OS will choose the right mode
for operation even if the attached SD card supports higher modes.
Change-Id: Idc7f1466ec71f4218f6b957cadeeffadd069eb2d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Since the new RTC is located in I2C bus 1 now, set the bus speed to
100 kHz as well.
Change-Id: Ica9468e559bc654545592a9b4d23f3164eafca8a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67102
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since the latest redesign a new RTC was introduced on mc_ehl2. Instead
of the old RX6110SA the new Micro Crystal RTC RV3028 is used now. Since
the address of this new RTC conflicts with an EEPROM on I2C bus 2, the
new RTC was moved to I2C bus 1.
As the mainboard is not finished yet, there are no incompatibility
issues with this change. Every new mainboard will have the new RTC and
the older mainboards are not delivered yet.
Change-Id: I3dd00855b8c9b22bdea21d3c8563cdb392868751
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
With a redesign of mc_ehl2 the used RTC was changed. In order to be able
to select a different RTC type for every variant move the RTC Kconfig
switch into the variant's Kconfig file.
Change-Id: Ia24703ede6a935e3b9886df87237857baec7d6a0
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67100
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds a driver for a new RTC from Micro Crystal. Supported
features are:
* configure backup voltage switchover via devicetree
* configure backup capacitor charging mode via devicetree
* set date if a voltage drop on backup voltage was detected
to either a user definable (devicetree) or coreboot build date
Change-Id: I37176ea726e50e4e74d409488981d7618ecff8bb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Updating from commit id e0a6a512b:
2022-02-03 22:59:34 +0100 - (Merge changes from topic "msm8916" into integration)
to commit id 7805999e6:
2022-09-05 16:42:34 +0200 - (Merge changes from topic "st-nand-updates" into integration)
This brings in 1030 new commits.
Change-Id: I981956fbdcbcfa4ce185652478b9bb30d40f5686
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The implementations of register_reset_to_bl31() are the same for
MedaiTek platforms, so we extract them to soc/common/bl31.c.
BUG=None
TEST=build pass
Change-Id: I297ea2e18a6d7e92236cf415844b166523616bdf
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Some of the pll settings are incorrect, which cause problems in GPU
after booting into kernel.
- MFGPLL opp_ck_en bit isn't located at MFGPLL_CON1, so we need to fix
it to enable MFGPLL properly.
- Switch SPMI clock muxes to 260M to avoid kernel hang while probing
SPMI kernel driver.
TEST=GPU bringup correctly.
BUG=b:233720142
Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Change-Id: I971109a5f72e3307899daaf5a5f26022124b559b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67355
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
The T4 of ANX7625 power on sequence should be larger than 0ms, but it's
-59ms now. So add 70ms delay between DSI_TE and LCM_RST.
BUG=b:242352915
TEST=The sequence T4 is larger than 0ms when power on.
Change-Id: I6b888707ec3c0612e396564e77c4cdbe92614dc5
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: wen zhang <zhangwen6@huaqin.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
This reduce the difference with linux v6.0-rc3.
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I15e1a935665c38b8a2109d412b1d16f935cbb402
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Lean Sheng Tan