This adds support for usb interrupt transfers in the EHCI driver. Split
transactions are supported, so this enables support for HID keyboards
devices over hubs in high-speed mode.
Change-Id: I9eb08f12b12c67ece10814952cb8651278b02f9d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1083
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The call to destroy_intr_queue was missing in usb_hid_destroy.
Change-Id: I51ccc6a79bc005819317263be24a56c51acd5f55
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1082
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
With split transactions, the EHCI host controller can handle full- and
low-speed devices on hubs in high-speed mode. This adds support for split
transactions for control and bulk transfers.
Change-Id: I30fa1ce25757f33b1e6ed34207949c9255f05d49
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1081
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds proper device attachment and detachment detection and port enable-
ment to the USB hub driver. Support for split transactions is still missing,
so this works only with USB2.0 devices on hubs in USB2.0 mode and USB1.1
devices on hubs in USB1.1 mode.
Change-Id: I80bf03f3117116a60382b87a4f84366370649915
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1080
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This removes a synthetic delay of 10ms from every mass storage command.
A delay here seems to be of no use and first tests have only shown a
huge speed increase.
Change-Id: Ida7423229373ec521d4326c5467a3f518b76149c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1071
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This disables some debugging code in the OHCI USB driver which causes
reboots under rare circumstances.
Change-Id: Ic274c162846137ee00638ffbc59ccf1d8130586f
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1074
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Due to operator precedence incomming USB commands were missing some
flags.
Change-Id: I87ef51590c9db7a6cbc7304e1ccac29895f8a51e
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Reviewed-on: http://review.coreboot.org/1084
Reviewed-by: Mathias Krause <minipli@googlemail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
UHCI commands should have a timeout of 30ms, not 30s!
Change-Id: Iebcf338317164eb1e683e1de850ffab5022ca3a1
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Reviewed-on: http://review.coreboot.org/1085
Reviewed-by: Mathias Krause <minipli@googlemail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Enable power on EHCI root hub ports only if the controller supports it.
Wait 20ms for the power to become stable.
Change-Id: I8897756ed2bfcb88408fe5e9f9e3f8af5dd900ac
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1078
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This function will be used by the USB hub driver.
Change-Id: I4d1d2e94f4442cbb636ae989e8ffd543181c4357
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1079
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The removal of bitfields came with some glitches in the UHCI driver. This
fixes it.
Change-Id: Iba8ea3b56b03c526eca7b6388c019568e00be6f5
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1069
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Commit c4348d0 ("libpayload: Remove bitfield use from OHCI data
structures") missed to adapt a debug message. This patch fixes this.
Change-Id: I5f6a4be9c7f6f99cb103926772717e15a3cbca70
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Reviewed-on: http://review.coreboot.org/653
Tested-by: build bot (Jenkins)
Reviewed-by: Bernhard Urban <lewurm@gmail.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
We don't use bitfields anymore.
Change-Id: I25ceec2024f659612871bcfe5f98df3a10789055
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/595
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
EHCI port status reporting isn't very consistent on power-on,
so just looking for devices on all ports is the safest way to
find everything.
Change-Id: I26b4305016f0bed1d2c1b5cffc59d5813fa1cbbb
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/594
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
When converting EHCI to not use bitfields, two offsets were converted
incorrectly.
Change-Id: I0bb4bad0eee42e54ad4fd53d6c35b107e227c41a
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/593
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
We agreed that bitfields are a Bad Idea[tm].
Change-Id: If4c4cb748af340e2721b89fea8e035da0632971f
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/480
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
We agreed that bitfields are a Bad Idea[tm].
Change-Id: I1b2bcda28c52ad10bbe9429e04d126b555f7828a
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/478
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
We agreed that bitfields are a Bad Idea[tm].
Change-Id: Ic04f151091c359912835b8b3db488d2d41bd4bbb
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/479
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
So far it was empty and never published. It now exists and shuts down
all controllers (esp. EHCI which resets the port routers).
Change-Id: I81e355e8a05778d6397675417b085a094a6f48ee
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/397
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
EHCI can take over all ports (and then reroute devices to
companion controllers if needs be). We do that, and then never
reset it.
Consequence:
Systems with only USB1 HC drivers (OHCI/UHCI) never see any devices.
Change-Id: If1d91e9142a6618289b0b3f6b56587ec857158e3
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/396
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
We have fatal(), which is just as good.
Coccinelle script:
@@
expression E;
@@
-usb_fatal(E)
+fatal(E)
Change-Id: Iabecbcc7d068cc0f82687bf51d89c2626642cd86
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/395
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
The USB stack is pretty noisy. Reduce the output to a sane level.
Change-Id: I250949e5cf74a8c6d43822b2e7487143b2ae1c65
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Reviewed-on: http://review.coreboot.org/393
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
OHCI works when USB_DEBUG is disabled, but not, when disabled.
This is because the controller requires some more time after a
schedule has finished.
Also improve compliance with the OHCI spec.
Change-Id: I4685cc485ff9c52b489fbaa352ab889671cff876
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/365
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Time for the brown paper bag: OHCI controllers are not happy when
told to send data, but with obviously wrong addresses. It helps
to write the addresses into the data structures.
Change-Id: Ic0967dc8939e64af119cfb89400a045a2c077171
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/306
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Some gcc versions seem to honor volatile at different places in a
struct declaration.
Change-Id: I0df2a3fb2eff4cee8cc1b8ac15d9cd9b86178752
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/155
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
I have observed two separate EHCI host bridges that do not tolerate
using C bit-fields to directly manipulate the portsc_t register. The
reason for this is that the EHCI spec says that port_enable must go
to 0 at the time that port_reset goes to 1. Naturally this cannot be
done using direct bit-field manipulation. Instead, we use a temporary
variable, change the bit-fields there, then atomically write the new
value back to the hardware.
Signed-off-by: Steven A. Falco <sfalco@coincident.com>
Change-Id: If138faee43e0293efa203b86f7893fdf1e811269
Reviewed-on: http://review.coreboot.org/101
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The Intel E6XX Atom processor reports an unknown USB controller type (in
addition to the standard EHCI and OHCI ones). Add a default case to
print a warning when an unknown controller type is detected.
Change-Id: I885d0ccec4c46fd212cceac599290e9bf85edbbb
Signed-off-by: Steven A. Falco <sfalco@coincident.com>
Reviewed-on: http://review.coreboot.org/100
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Other USB drivers set the bus_address field. EHCI should do this too.
Signed-off-by: Steven A. Falco <sfalco@coincident.com>
Change-Id: Ic4274c6744951ef7fa0cb135caf8b9f177d8bcaf
Reviewed-on: http://review.coreboot.org/99
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
The new build system uses quite a few more -W flags for the compiler by
default than the old one. And that's for the better.
Change-Id: Ia8e3d28fb35c56760c2bd0983046c7067e8c5dd6
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/72
Tested-by: build bot (Jenkins)
Reviewed-by: Uwe Hermann <uwe@hermann-uwe.de>
Interrupt transfer support is missing (ie. no keyboard),
bulk and control transfers work (ie. mass storage).
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5845 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and 5. They're not found if only function 0 is checked. So if a device
exists at all, try all its functions. usb_controller_initialize() will
silently skip all device classes != 0C03.
(changed to continue to use 32bit accesses -pg)
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5774 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Improve scanning for USB controllers.
Limitations:
- OHCI doesn't support interrupt transfers yet (ie. no keyboards)
- xHCI just does initialization and device attach/detach so far
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5691 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5631 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Move controller specific data structures into private headers,
to avoid conflicts between controller drivers.
Factor out the USB PID ids, which are only exposed on UHCI. It's
of not much use on the other controllers.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5616 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
while others dislike them being extra commits, let's clean them up once and
for all for the existing code. If it's ugly, let it only be ugly once :-)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5507 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- support MMC2 devices
- make usb stack more solid
- drop some unused functions
- fix lowspeed/speed naming
- add support for "quirks"
- improve usbhid driver
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5299 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- fix minor bug in serial driver.
- latest USB stack fixes
- fix dead store in options.c
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4239 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Rename the generated config file to libpayload-config.h to differenciate
it from other config.h files. Move the default location of the file to
$(src)/include so that LIBPAYLOAD_PREFIX= users can access the file
without staging it.
Signed-off-by: Jordan Crouse <jordan@cosmicpenguin.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3768 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
replaces it with two queues (input, output) where drivers (serial,
keyboard, video, usb) can attach.
The only things left with #ifdefs are initialization (at some point
the drivers must get a chance to register)
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3679 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
560bytes/controller)
- no need for the client of libpayload to implement
usbdisk_{create,remove}, just because USB was compiled in.
- usb hub support compiles, and works for some trivial cases (no device
detach, trivial power management)
- usb keyboard support works in qemu, though there are reports that it
doesn't work on real hardware yet.
- usb keyboard is integrated in both libc-getchar() and curses, if
CONFIG_USB_HID is enabled
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3662 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
memalign implementation (eg. the one I sent yesterday).
Features:
- UHCI controller driver
- UHCI root hub driver
- USB MSC (Mass Storage Class) driver
- skeleton of a USB HID driver
(requires better interrupt transfer handling, which is TODO)
- skeleton of a USB hub driver
(needs several blank spots filled in, eg. power management.
Again: TODO)
OHCI and EHCI are not supported, though OHCI support should be rather
easy as the stack provides reasonable abstractions (or so I hope). EHCI
will probably be more complicated.
Isochronous transfers (eg. webcams, audio stuff, ...) are not supported.
They can be, but I doubt we'll have a reason for that in the boot
environment.
The MSC driver was tested against a couple of USB flash drives, and
should be reasonably tolerant by now. But I probably underestimate
the amount of bugs present in USB flash drives, so feedback is welcome.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3560 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Nico Huber