CB:31250 ("soc/intel/cannonlake: Configure GPIOs again after FSP-S is
done") introduced a workaround in coreboot for `soc/intel/cannonlake`
platforms to save and restore GPIO configuration performed by
mainboard across call to FSP Silicon Init (FSP-S). This workaround was
required because FSP-S was configuring GPIOs differently than
mainboard resulting in boot and runtime issues because of
misconfigured GPIOs.
This issue has since been fixed in FSP (verified with FSP v1263 on
hatch). However, there were still 4 boards in coreboot using
`cnl_configure_pads()`. As part of RFC CB:50829, librem_cnl, clevo/cml-u
and system76/lemp9 were tested to ensure that this workaround is no
longer required.
This change drops the workaround using `cnl_configure_pads()` and
updates all mainboards to use `gpio_configure_pads()` instead.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Tested-by: Angel Pons <th3fanbus@gmail.com>
(Tested purism/librem_cnl)
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
(Tested clevo/cml-u which is similar to system76/lemp9)
Change-Id: I7a4facbf23fc81707cb111859600e641fde34fc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52248
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update GPIO config based on review of latest schematics:
- LAN/WLAN reset lines are NC
- SDIO lines configured via GPP_G0-G7
- DMIC lines are wired directly to codec, not PCH, so GPP_D17-20
are set to NC
- Pads GPP_H0-H3 are configured for I2S2
- Pads GPP_H7-H9 are straps for board revision, so treated as GPI
- CPU_C10_GATE# is NC
- PWRBTN# does not need an internal pull-up
- GPP_C20-23 are configured for M.2 UART
- SATAXPCIE1/2 and EC SCI/SMI lines do not need internal pull ups
- GPP_C6/C7 set to I2C1 for future use
- GPP_E15 changed from SCI to SMI, edge triggered
Change-Id: If113cfeadf093e10dd84ab827ead594088f02ba1
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52389
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When a pad is configured as NC, it is set as a GPI with both
TX and RX disabled, and as the pad is internally disconnected,
no pull up or pull down is needed.
Change-Id: Id551b8f6f5b8c772e17670b8b728b5e890ef0b21
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52388
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
IPMI debug was extra spewy, so add a debug option as SPI and
other drivers have when they need to be debugged.
Change-Id: I788d67c242cac23bde9750aa3e95e3276c3f1fd7
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The default of 32 buses per hotplug bridge is rather high. Especially
for platforms that limit MMConf space to 64 buses: they run out of
numbers if there is more than a single hotplug bridge.
Lower the default to
* 8 if MMConf is limited to 64 or less buses,
* 16 if MMConf is limited to 128 or less buses.
Change-Id: I06d522dd92ceea9f4798273b26f947a5333800c3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52069
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
More relational operators were added to Kconfig in 2015. Now we can
make use of them.
Change-Id: I640e5c3ee1485348f09fcb0b0d5035eb53a2c98e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
I wished there was a way to do this in smaller steps, but with
every line fixed an error somewhere else became visible. Here
is a (probably incomplete) list of the issues:
* Only one set of parentheses was supported. This is a hard
to solve problem without a real parser (one solution is to
use an recursive RE, see below).
* The precedence order was wrong. Might have been adapted just
to give a positive result for the arbitrary state of the tree.
* Numbered match variables (e.g. $1, $2, etc.) are not local.
Calling handle_expressions() recursively once with $1, then
with $2, resulted in using the final $2 after the first
recursive call (garbage, practically).
Also, symbol and expression parsing was mixed, making things
harder to follow.
To remedy the issues:
* Split handle_symbol() out. It is called with whitespace
stripped, to keep the uglier REs in handle_expressions().
* Match balanced parentheses and quotes when splitting
expressions. In this recursive RE
/(\((?:[^\(\)]++|(?-1))*\))/
the `(?-1)` references the outer-most group, thus the whole
expression itself. So it matches a pair of parentheses with
a mix of non-parentheses and the recursive rule itself inside.
This allows us to:
* Order the expression matches according to their precedence
rules. Now we can match `<expr> '||' <expr>` first as we should
and everything else falls into its place.
* Remove the bail-out that silenced the undefined behavior.
Change-Id: Ibc1be79adc07792f0721f0dc08b50422b6da88a9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Set the SATA and SSATA REGLOCK as indicated by the Intel documentation.
Change-Id: I90e6d0e3b5a38bcd5392e26cbbb6dc4aa6a8304b
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add the SATA device to the device tree so it may be found
when trying to write SATA registers. Otherwise, it fails
on "requests hidden 00:17.0 PCI: dev is NULL!"
Change-Id: Ia309805ffd6e97d04b5cf4a0344eaac4c4d0adb6
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Set MSR locks as indicated by the Intel documents.
The following MSRs settings are locked:
MSR_FEATURE_CONFIG AES enable/disable lock
TURBO_ACTIVATION_RATIO_LOCK
This also adds PARALLEL_MP_AP_WORK to enable running on APs to set
each CPU MSR.
Change-Id: Iacf495f0880d42b378cb0d2c37940d50a511c430
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
MPTS is currently not executed by the AML interpreter.
Use Method (\\_SB.MPTS) instead of
Scope (\\_SB)
Method (MPTS)
ScopeEnd
Tested on Prodrive Hermes. MPTS is now executed at S5.
Change-Id: I9074eb4ba55aab3f9a47ae5e3c3ddd338406a5e4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: <wouter.eckhardt@prodrive-technologies.com>
Since there are some differences between picasso PSP svc and cezanne PSP
svc, each platform should have their own svc wrapper.
Moreover cezanne PSP will drop unused parameters from
update_psp_bios_dir and save_uapp_data so make wrapper around it.
BUG=b:182477057
BRANCH=none
TEST=build psp_verstage and boot on zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I69f998865fc3184ea8900a431924a315c5ee9133
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52307
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
psp_verstage is not specific to picasso. There might be picasso-specific
code but move everything into common as a first step. While developing
psp_verstage for cezanne picasso-specific code will move back to picasso
directory.
BUG=b:182477057
BRANCH=none
TEST=build psp_verstage on zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ifb1df0d82b972f28be2ffebd476c2553cbda9810
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This change implements `gpio_snapshot()` and `gpio_verify_snapshot()`
callbacks that are useful for debugging any GPIO configuration changes
across FSP-S. These can be utilized by all Intel SoCs that make use of
the common block GPIO driver.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I82a1f125c490b9d6e26e6e9527c2fcd55bb9d429
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Traditionally, for each Intel platform using FSP, FSP-S has at some
point configured GPIOs differently than the mainboard configuration in
coreboot. This has resulted in various side-effects in coreboot,
payload and OS because of misconfigured GPIOs. On more recent Intel
platforms, a UPD `GpioOverride` is added that coreboot can use to
ensure that FSP does not touch any GPIO configuration.
This change adds a debug option `CHECK_GPIO_CONFIG_CHANGES` to fsp2_0
driver in coreboot that makes a platform callback `gpio_snapshot` to
snapshot GPIO configuration before making a call to FSP SiliconInit
and Notify phases. This snapshot is then compared against the GPIO
configuration using platform callback `gpio_verify_snapshot` after
returning from FSP. The callbacks are not added to romstage (FSP-M)
because mainboard configures all pads in ramstage.
This debug hook allows developers to dump information about any pads
that have a different configuration after call to FSP in ramstage. It
is useful to identify missed UPD configurations or bugs in FSP that
might not honor the UPDs set by coreboot.
This debug hook expects the platform to implement the callbacks
`gpio_snapshot` and `gpio_verify_snapshot`. These can be implemented
as part of the common GPIO driver for platforms using
FSP2.0+. Platforms that implement this support must select the config
`HAVE_GPIO_SNAPSHOT_VERIFY_SUPPORT` to make the debug config
`CHECK_GPIO_CONFIG_CHANGES` visible to user.
Proposal for the GPIO snapshot/verify support was discussed in the RFC
CB:50829.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I5326fc98b6eba0f8ba946842253b288c0d42c523
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50989
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add ACPI code to enable the backlight when we enter the OS.
BUG=b:184198808
TEST=Backlight enabled in the OS
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I3e0a6c06120ac5abf0a0d82494e03d9cf80c1f8c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52113
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Kconfig value specified Intel instead of AMD.
BUG=b:184198808
TEST=Backlight enabled in the OS
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I9fbdf821591ec886f383c1a5ac197f8f213c4cc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52384
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Both touchpads supported by zork use level-triggered wakeup signal.
BRANCH=zork
BUG=b:172846122,b:182911201
TEST=1. cros build-ap -b zork
2. both Synaptics and ELAN touchpads work fine on Vilboz
3. Wakeup source is correctly reported on Vilboz
Signed-off-by: Victor Ding <victording@google.com>
Change-Id: Icc2b5ad3bd434c9759a0fdfc121aa3c94f46630e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52367
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on the datasheet provided by ELAN, the /INT pin is "low active"
and "indicates touchpad likes to send data to system(host) when low".
The signal is level-triggered.
BRANCH=zork
BUG=b:172846122
TEST=cros build-ap -b zork
Signed-off-by: Victor Ding <victording@google.com>
Change-Id: I1f2182aaf483932304591ab14592f35214ea6efd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52366
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The headers added are generated as per FSP v2117_00.
Previous FSP version was v2081_02.
Changes Include:
- Adjust Reserved UPD Offset in FspmUpd.h and FspsUpd.h
- Remove FivrFaults and FivrEfficiency Upds from FspmUpd.h
- Few UPDs description update in FspmUpd.h and FspsUpd.h
BUG=b:184129128
BRANCH=None
TEST=Build and boot ADLRVP
Change-Id: I068552084b1ef3e5c4fba7a46240d116c92c7b5b
Cq-Depend: TBD
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This pad is connected to INTP_OUT of the Type-C PD controller. Correct
the comment. Also remove the unneeded pull-up.
Checked with schematics.
Change-Id: I16a769ac6a2d54da700ddb45bd9c7c84383a43dd
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
This pad is connected to INTP_OUT of the Type-C PD controller. Correct
the comment. Also remove the unneeded pull-up.
Checked with schematics.
Change-Id: I33a5f177affc3f13d091a85073499b7283f54ada
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add the following locks as recommended by the Intel docs:
DRAM_POWER_INFO_LOCK
PCU_CR3_FLEX_RATIO_LOCK
TURBO_ACTIVATION_RATIO_LOCK
PCU_CR0_PMAX_LOCK
Change-Id: I8d8211977e87109a91790a4070454fc561aa761b
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Call the SMM finalize SMI. Adds SMM_FEATURE_CONTROL setting to enable
MCHK on code fetch outside SMRR and the register lock as recommended
by the BWG.
Change-Id: Ie3b58d35c7a62509e39e393514012d1055232d32
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51651
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Rocky Phagura
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set the flash PRR3 and PRR4 lock to be set with SPI FLOCKDN.
Change-Id: I288eea3e0e853e5067c5af23e22eab79330c0f20
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51779
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CBFS size equals flash size, leaving no space for descriptor and ME.
Reduce CBFS_SIZE.
BUG = N/A
TEST = Build and boot Portwell M107
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Change-Id: Ida5a248edf4f602c4a106ae29d706e732ef8454f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
TPM_INIT_RAMSTAGE needs to be enabled for measured boot only
configuration.
Remove TPM_INIT_RAMSTAGE disable.
BUG = NA
TEST = Boot possible combinations of VBOOT, measured boot and vendorcode
security.
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Change-Id: I91bde691d445d4210429c928e90e16653092f1cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The darp5 has several GPIO differences to the galp3-c, which are already
accounted for in gpio.c.
Change-Id: I951e86e53e9c47b9f3038927f44e505d37200c26
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add generate_cpu_entries to device operations. Add support to
generate cpu p-state and c-state SSDT entries.
BUG=b:184151560
TEST=Dump and verify SSDT entry for CPU p-states and c-states.
Change-Id: I77d8078b94fb661dc045b4184955c8cbec373d12
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Three stages of the new tint build system:
1) generate_core.sh extracts the core part from buildgcc script,
most importantly the checksum calculation/verification functions.
2) tintify_core.sh adds the tint-specific footer/header to the core,
such as the properties of current version including its checksum.
3) tint.sh - generated and "tintified" core script - builds a tint.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: Ib71f5b861ecf91949a5af12812258e60873f0498
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add uart controller to chipset.cb and leave it off by default.
Turn uart0 on for console for mainboards.
BUG=none
TEST=builds and boot into OS
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Iaeb7fea4b92bd89331c7ae7c1c000f8d9961fe9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
TCSS OC pins has not been correctly configured for brya.
This patch fills the value from devicetree to correct the OC pins
mapping
BUG=b:184653645
BRANCH=None
TEST=check if UPD value has been reflected correctly
Change-Id: Ia21cdbf5768ad7516ea52bff7e247291a7d2ebd1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
We need to change OC pin for type C USB3 ports and it depends
on the board design. Allowing it to be filled by devicetree will
make it easier to change the mapping based on the board design
BUG=b:184653645
BRANCH=None
TEST=compilation works fine and value of UPD is getting reflected.
Change-Id: I61faa661c12dced27c6cdd7005a61ae8de8621e1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Add log to show the codec has been disabled.
BUG=b:185193926
TEST=cbmem -c | grep disabled, can find the codec name
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I8ce7e435ce73beb2a5cbf5883905554227b1989b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
When MRC cache region type is not found (for example, in recovery mode
with !HAS_RECOVERY_MRC_CACHE), mrc_cache_stash_data() will return 0.
Therefore, the platform code is not able to tell from the return value
if the MRC cache data is actually written to flash or not. Since the MRC
driver is already pretty verbose, ignore the return value and remove the
misleading memory logs.
BUG=none
TEST=emerge-asurada coreboot
BRANCH=asurada
Change-Id: I6b411664ca91b9be2d4518a09e9734d26db02d6e
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52361
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Needed so we can switch to normal mode.
BUG=b:184126844
TEST=Boot guybrush in developer mode and switch to normal mode.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I26ad160a2372484e9753a727f2b454a31e3537a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This is the same as zork.
BUG=b:184126844
TEST=Boot guybrush in developer mode and switch to normal mode.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib11c255ab7e937de334ecd18dc030006f7724275
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
There is no need to stash the SCI trigger register configuration and
apply it at the end. Remove this to make SCI and SMI programming more
symmetrical and to use available configure_scimap function instead of
implementing it again, but without the additional checks. Using this
function also allows removing soc_route_sci.
Change-Id: Ie23da79546858282910db65182a6315ade506279
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Furquan Shaikh