This patch allows the CBMEM console to persist across reboots, which
should greatly help post factum debugging of issues involving multiple
reboots. In order to prevent the console from filling up, it will
instead operate as a ring buffer that continues to evict the oldest
lines once full. (This means that if even a single boot doesn't fit into
the buffer, we will now drop the oldest lines whereas previous code
would've dropped the newest lines instead.)
The console control structure is modified in a sorta
backwards-compatible way, so that new readers can continue to work with
old console buffers and vice versa. When an old reader reads a new
buffer that has already once overflowed (i.e. is operating in true ring
buffer mode) it will print lines out of order, but it will at least
still print out the whole console content and not do any illegal memory
accesses (assuming it correctly implemented cursor overflow as it was
already possible before this patch).
BUG=chromium:651966
TEST=Rebooted and confirmed output repeatedly on a Kevin and a Falco.
Also confirmed correct behavior across suspend/resume for the latter.
Change-Id: Ifcbf59d58e1ad20995b98d111c4647281fbb45ff
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18301
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When console input driver registers itself, perform flush of input
buffer to avoid interpreting any stale key presses before libpayload
is run.
keyboard.c: Remove the redundant buffer flush.
8250.c: Ensure that serial_hardware_is_present is set before call to
add input driver.
BUG=b:37273808
TEST=Verified that any key presses in serial console before payload is
up do not have any effect after the payload starts running.
Change-Id: I46f1b6715ccf6418f5b2c741bf90db2ece26a60d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19345
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
CBGFX currently doesn't support portrait screens at all. This will have
to be fixed eventually but might take a bit of effort. As a first step
to make devices with a portrait panel somewhat usable, this patch will
just force a square canvas on these panels and keep the bottom part of
the screen black.
Also switch set_pixel to calculate framebuffer position via
bytes_per_line instead of x_resolution. This is supposed to be the
canonical way to do that and may differ in cases where the display
controller requires a certain alignment from framebuffer lines.
Change-Id: I47dd3bf95ab8a7d8b7e1913e0ddab346eedd46f1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19279
Tested-by: build bot (Jenkins)
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
This adds a gru libpayload config, that should fit all gru-based
devices such as kevin.
As gru-based devices are CrOS devices, select the associated config
to enable CrOS-specific features.
Change-Id: I6e79b763fc497c126612b8786a669a33b57ea29f
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: https://review.coreboot.org/19137
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
We have found a non-compliant USB hub (RealTek RTS 5413) that does not
set a port's Connect Status Change bit on its USB 3.0 half if the port
had already been connected while the hub was being reset. To work around
this bug, this patch adds code to initially request the status of every
port after a hub was enumerated, clear the Connect Status Change bit if
set, and then enumerate the port iff it is currently connected,
regardless of whether the change bit was set. A similar behavior can
also be found in the Linux kernel.
BRANCH=oak
BUG=b:35929438
TEST=Booted Elm with this change, my USB 3.0 sticks enumerate now even
if they had been plugged in since boot.
Change-Id: I8a28252eb94f005f04866d06e4fc61ea265cee89
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18729
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Allows to use SSE and floating point in payloads without digging to
much into x86 assembly code.
Tested on Lenovo T500 (Intel Core2Duo).
Both floating point operation and SSE is properly working.
Change-Id: I4a5fc633f158de421b70435a8bfdc0dcaa504c72
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18345
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This adds an oak libpayload config, that should fit all oak-based
devices such as elm.
Change-Id: Iabb71404ff84029a5976371a353e8c92e781ca1f
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: https://review.coreboot.org/18447
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
Some simple implementation of the MultiBoot protocol may not pass a
memory map (MULTIBOOT_FLAGS_MMAP missing in the flags) but just the two
values for low and high memory, indicated by the MULTIBOOT_FLAGS_MEMINFO
flag.
Support those kind of boot loaders too, instead of falling back to the
hard-coded values in lib_get_sysinfo().
Tested with a multiboot enhanced version of FILO.
Change-Id: I22cf9e3ec0075aff040390bd177c5cd22d439b81
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18350
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Implement the argc/argv passing as described in coreboot’s payload API:
http://www.coreboot.org/Payload_API
While at it, give the code some love by not needlessly trashing register
values.
Change-Id: Ib830f2c67b631b7216843203cefd55d9bb780d83
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18336
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Simplify the code by directly using the arguments on the stack as base
pointer relative memory references, instead of loading them into
intermediate registers first.
Make it more robust by preserving all callee saved registers mandated by
the C calling convention (and only those), namely EBP, EBX, ESI and EDI.
Don't assume anything about the register state when the called function
returns -- beside the segment registers and the stack pointer to be
still the same as before the call.
Change-Id: I383d6ccefc5b3d5cca37a1c9b638c231bbc48aa8
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18335
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
According to coreboot’s payload API [1], the called payload should be
able to return a value via %eax. Support this by changing the prototype
of start_main() and pass on the return value of main() to the caller
instead of discarding it.
[1] https://www.coreboot.org/Payload_API
Change-Id: I8442faea19cc8e04487092f8e61aa4e5cba3ba76
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18334
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
According to coreboot’s payload API [1] the argc value should be passed
at stack offset 0x10, so we need to push a dummy value to comply to the
API.
[1] https://www.coreboot.org/Payload_API
Change-Id: Id20424185a5bf7e4d94de1886a2cece3f3968371
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18333
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The pointer to write the return value to is in %ecx, not %eax. Writing
to (%eax) leads to memory corruptions as %eax holds the return value,
e.g. would write zero to address zero for a "successful" returning
payload.
Change-Id: I82df27ae89a9e3d25f479ebdda2b50ea57565459
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18332
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
According to coreboot’s payload API [1] the magic value passed to the
payload should be 0x12345678, not 12345678. Fix that.
[1] https://www.coreboot.org/Payload_API
Change-Id: I10a7f7b1a4aec100416c5e7e4ba7f8add10ef5c5
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18331
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When .xcompile doesn't already exist, building libpayload fails because
the CC variable (et al) remain empty since .xcompile is only included
after the variables coming from there are evaluated.
Change-Id: I73f1cbced95afcff15839604fea5fd05d81bc3d3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18228
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
It takes a long time for no gain: We don't need to update the
submodules, we don't need to fetch the revision, we don't need to find
the compilers, when all we want to do is to manipulate the .config file
or clean the build directory.
Change-Id: Ie1bd446a0d49a81e3cccdb56fe2c43ffd83b6c98
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18182
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Power button events are usually dropped because the button is not in
the keyboard matrix range. Add condition to forward it like other keys.
BUG=chrome-os-partner:61275
BRANCH=None
TEST=reboot and make sure power button selection
in depthcharge's detachable menus is processed on reef.
Change-Id: I86897fa8d73a56533ef62bba05458ac3d339237e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 25654e214f0ab8685d445ced62612a02be851126
Original-Change-Id: I516a0043bd7730789728d5c5498d0a0f30a2acac
Original-Signed-off-by: Shelley Chen <shchen@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/428199
Original-Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://review.coreboot.org/18177
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
This enables USB HID support in the veyron config, since it seems to
work correctly and is needed for interaction with depthcharge on devices
without an embedded keyboard (such as veyron_mickey).
Change-Id: Icae829e3a132005df17bcb6f7e6f8a190912576d
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: https://review.coreboot.org/17930
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
Currently we just disabled ohci interrupts when calling ohci_shutdown,
Which would not actually shutdown the ohci controller, for example it
may still written the increased HccaFrameNumber to Hcca buffer.
Perform a soft reset to ohci controller as the linux kernel ohci-hcd
driver does.
BUG=chrome-os-partner:60996
BRANCH=None
TEST=Checked on gru, no more "BUG: Bad page state" error in kernel.
Change-Id: I128ab6ba455ac5383a4d48be0bc12b8bb4533464
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4749fc82fdd1b74ca3f2ed3fdf0ef53a5e161087
Original-Change-Id: I3f192aea627ba2fa69533bc0a4270466ca18f2a7
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/426338
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/18125
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
BUG=chrome-os-partner:56947
TEST=Verifed country code can be parsed from VPD in depthcharge.
BRANCH=None
Change-Id: I2fbbd4a784c50538331747e1ef78c33c6b8a679b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: acea6e2a200e8bd78fd458255ac7fad307406989
Original-Change-Id: I4616fefc6a377d7830397cdadb493927358e25cc
Original-Signed-off-by: Kan Yan <kyan@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/425819
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18124
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This updates the configuration for ARM CrOS devices (nyans and veyrons)
by using the CHROMEOS Kconfig option, thus reducing the number of
options to select. It also brings proper serial console support.
Change-Id: Iffc84c44a1d339c5bb575fbaffc40bc2d56bb6cf
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: https://review.coreboot.org/17928
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This fixes the generic timer driver to get the current tick from the
high register, so that comparison with the high count value (obtained
previously from the same register) has a chance to succeed.
Change-Id: I5ce02bfa15a91ad34641b8e24813a5b7ca790ec3
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: https://review.coreboot.org/17929
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Coverity considers this a copy&paste error, and maybe it is. In any
case, it makes sense to check the variable that (if the condition is
true) is changed, and the values are the same before that test, so the
change is harmless.
Change-Id: I163c6a9f5baa05e715861dc19643b19a9c79c883
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1347376
Reviewed-on: https://review.coreboot.org/17837
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Coverity erroneously complains that we call wmove with x or y == -1,
even though our copy of that function properly checks for that.
But: setsyx is documented to always return OK (even on errors), so let
it do that. (and make coverity happy in the process)
Change-Id: I1bc9ba2a075037f0e1a855b67a93883978564887
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1260797
Reviewed-on: https://review.coreboot.org/17836
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Coverity complains and that (unfortunately) means that some compiler
might take advantage of the same fact.
Change-Id: I59aff77820c524fa5a0fcb251c1268da475101fb
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1261105
Reviewed-on: https://review.coreboot.org/17835
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
MAX_ARGC_COUNT limits the payload to ten parameters which is not
enough when used with a proprietary first stage bootloader providing
hardware description using around 20 parameters.
This patch makes the libpayload able to get up to 32 parameters.
Change-Id: I49925040d951dffb9c11425334674d8d498821f2
Signed-off-by: Jeremy Compostella <jeremy.compostella@gmail.com>
Reviewed-on: https://review.coreboot.org/17467
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Chrome OS builds always have some inherent differences to "standard"
libpayload configurations: they don't want to use curses or things like
storage drivers, they always use the coreboot framebuffer and USB, etc.
This patch reintroduces CONFIG_LP_CHROMEOS as an option that only
affects Kconfig defaults. This allows Chrome OS builds to select most of
what they need in one go and reduces board-specific .config files to
only the options that are really specific to that board.
Also restricts the 8250_SERIAL_CONSOLE Kconfig to only default to yes on
x86 boards, which probably makes sense for all of libpayload (some but
far from all ARM boards use 8250-compatible UARTs, and we should
probably not default a platform option unless it's going to be correct
with very high probability).
BRANCH=None
BUG=None
TEST=Built and booted Jerry and Oak.
Change-Id: Ie0c0593ffd399608d2cbfb83d20891f6f1864914
Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Id: e558f59
Original-Change-Id: I609637cd2ea7dfb4558aa3c04c90b64038c9ab57
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/347970
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17024
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Currently every non-x86 platform supported by libpayload needs to
provide its own timer driver. Most of the ones we have accumulated there
look almost identical: For the frequency, return a preset constant. For
the value, read a 32-bit register, possibly read another 32-bit register
and shift+OR it with the previous one, then return that.
Let's replace this with a single .c file that can easily handle all of
those cases. Menuconfig convenience can still be maintained by providing
several presets that select different defaults for the driver's
configuration options (register address(es) and frequency).
Removes an "enabled" check from Samsung MCT driver since coreboot always
unconditionally enables that timer anyway.
CQ-DEPEND=CL:344809
BRANCH=None
BUG=None
TEST=Booted Oak and Veyron, observed how dev-mode delay was still ~30s
Change-Id: I61cb7d2ffd4902aa841c57f9afa9cd991f770acd
Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Id: a036af6
Original-Change-Id: I9784e7c6aa5abd6d92478ea7ec1cf42c9a437546
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/347749
Reviewed-on: https://review.coreboot.org/17023
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch makes strtok_r:
- handle the end of the string
- handle string that contains only delimiters
- do not set ptr outside of str
Change-Id: I49925040d951dffb9c11425334674d8d498821f1
Signed-off-by: Jeremy Compostella <jeremy.compostella@gmail.com>
Reviewed-on: https://review.coreboot.org/16524
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
All but ga-g41m-es2l/cmos.default had multiple final newlines.
ga-g41m-es2l/cmos.default had no final newline.
Change-Id: Id350b513d5833bb14a2564eb789ab23b6278dcb5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16361
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Antonello Dettori <dev@dettori.io>
This patch adds functionality to compile a C data structure into a raw
binary file, add it to CBFS and allow coreboot to load it at runtime.
This is useful in all cases where we need to be able to have several
larger data sets available in an image, but will only require a small
subset of them at boot (a classic example would be DRAM parameters) or
only require it in certain boot modes. This allows us to load less data
from flash and increase boot speed compared to solutions that compile
all data sets into a stage.
Each structure has to be defined in a separate .c file which contains no
functions and only a single global variable. The data type must be
serialization safe (composed of only fixed-width types, paying attention
to padding). It must be added to CBFS in a Makefile with the 'struct'
file processor.
Change-Id: Iab65c0b6ebea235089f741eaa8098743e54d6ccc
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16272
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
3 out of 4 architectures currently zero out the payload BSS in early
assembly code, which is pointless since the code loading the payload has
already done that (with a more efficient memset). ARM64 has never had
any code like this and can run just fine without it. This also defeats
the new optimization of moving the heap out of the BSS, since all three
implementations assume that everything between _edata and _end is BSS.
We should just take this out.
Change-Id: I45cd2dabd94da43ff0f77e990f11c877cee6cda1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16091
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
cbfs_get_handle() allocates memory for a handle and doesn't free it if
it errors out later, leaving the memory permanently leaked. Fix.
Change-Id: Ide198105ce3ad6237672ff152b4490c768909564
Reported-by: Coverity
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16207
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Allocating a 15980-byte scratchpad on the stack when your default stack
size is set to 16KB is really not a great idea. We're regularly
overflowing into the end of our heap when using LZMA in libpayload, and
just happen not to notice it because the heap rarely gets filled up all
the way. Of course, since we always *have* a heap in libpayload, the
much saner solution is to just use it directly to allocate the
scratchpad rather than accidentally grow backwards into it anyway.
Change-Id: Ibe4f02057a32bd156a126302178fa6fcab637d2c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16089
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The ARM64 MMU code maintains a list of used ranges, to avoid mapping the
DMA buffer over the coreboot tables and things like that. Unfortunately,
the overlap with ranges in that list is checked with
(start1 >= start2 && start1 <= end2) || (end1 >= start2 && end1 <= end2)
which is not a full overlap check and misses the case where the second
region is completely contained within the first. This patch replaces
that code with a properly vetted primitive from Stack Overflow.
BRANCH=none
BUG=chrome-os-partner:54416
TEST=Observe how Kevin recovery screen now gets drawn at 10x the speed.
Change-Id: I7e2706426762794e160d743bbfc40da1e26eee12
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16075
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Move the configuration of the timer, storage and USB drivers from the
main Kconfig to three separate ones stored in the respective
directories.
This reduces the LOC of Kconfig and makes it more manageable.
Change-Id: I0786dbc1d5d8317c8ccb600f5de9ef4a8243d035
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/15914
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This removes the newlines from all files found by the new
int-015-final-newlines script.
Change-Id: I65b6d5b403fe3fa30b7ac11958cc0f9880704ed7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15975
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
cbgfx currently makes a separate function call (recomputing some values)
for every single pixel it draws. While we mostly don't care that much
about display speed, this can become an issue if you're trying to paint
the whole screen white on a lowly-clocked Cortex-A53. As a simple
solution for these extreme cases, we can build a fast path into
clear_screen() that just memset()s the whole framebuffer if the color
and pixel format allow it.
BUG=chrome-os-partner:54416
TEST=Screen drawing speed on Kevin visibly improves (from 2.5s to 3ms).
Change-Id: I22f032afbb86b96fa5a0cbbdce8526a905c67b58
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15524
Tested-by: build bot (Jenkins)
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Make the xHCI driver to support xHCI controller v1.1
2. And a new function xhci_ring_doorbell(), it aims to
add a memory barrier before ringing the doorbell, to ensure
all TRB changes are written to memory.
BRANCH=none
BUG=chrome-os-partner:52684
TEST=boot from USB on Kevin rk3399 platform
Change-Id: Ife1070d1265476d0f5b88e2acf3299fc84af5832
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 0c21e92
Original-Change-Id: I4e38e04dc3c7d32ee4bb424a473c70956a3c3ea9
Original-Signed-off-by: Liangfeng Wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/346831
Original-Commit-Ready: Brian Norris <briannorris@chromium.org>
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15111
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Some exceptions (like from calling a NULL function pointer) are easier
to narrow down with a dump of the call stack. Let's take a page out of
ARM32's book and add that feature to ARM64 as well. Also change the
output format to two register columns, to make it easier to fit a whole
exception dump on one screen.
Applying to both coreboot and libpayload and syncing the output format
between both back up.
Change-Id: I19768d13d8fa8adb84f0edda2af12f20508eb2db
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/14931
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The libpayload CBFS APIs are pretty old and clunky, primarily because of
the way the cbfs_media struct may or may not be passed in and may be
initialized inside the API calls in a way that cannot be passed back out
again. Due to this, the only real CBFS access function we have always
reads a whole file with all metadata, and everything else has to build
on top of that. This makes certain tasks like reading just a file
attribute very inefficient on non-memory-mapped platforms (because you
always have to map the whole file).
This patch isn't going to fix the world, but will allow a bit more
flexibility by bolting a new API on top which uses a struct cbfs_handle
to represent a found but not yet read file. A cbfs_handle contains a
copy of the cbfs_media needed to read the file, so it can be kept and
passed around to read individual parts of it after the initial lookup.
The existing (non-media) legacy API is retained for backwards
compatibility, as is cbfs_file_get_contents() (which is most likely what
more recent payloads would have used, and also a good convenience
wrapper for the most simple use case), but they are now implemented on
top of the new API.
TEST=Booted Oak, made sure that firmware screens and software sync
worked okay.
Change-Id: I269f3979e77ae691ee9d4e1ab564eff6d45b7cbe
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/14810
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Extend the serial port description to include the input clock frequency
and a payload specific value.
Without the input frequency it is impossible for the payload to compute
the baud-rate divisor without making an assumption about the frequency.
This breaks down when the UART is able to support multiple input clock
frequencies.
Add the UART_PCI_ADDR Kconfig value to specify the unique PCI device
being used as the console UART. Specify this value as zero when the
UART is not on the PCI bus. Otherwise specify the device using bus,
device and function along with setting the valid bit.
Currently the only payload to consume these new fields is the EDK-II
CorebootPayloadPkg.
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file:
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the pdat.bin files in the location specified by
CONFIG_FSP_PDAT_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Build EDK2 CorebootPayloadPkg/CorebootPayloadPkgIa32.dsc to generate
UEFIPAYLOAD.fd
* Testing is successful when CorebootPayloadPkg is able to properly
initialize the serial port without using built-in values.
Change-Id: Id4b4455bbf9583f0d66c315d38c493a81fd852a8
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14609
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
BUG=chrome-os-partner:49249
TEST=None. Initial code not sure if it will even compile
BRANCH=none
Change-Id: Ibf2c91be93e2567cc1262b6fb84461eef51ab3e0
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b87157138302b017e64a28417a22421c880c1bcb
Original-Change-Id: I16a8324d3c8ef4ee729f4509fda5bfe703b24ce4
Original-Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/333304
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: https://review.coreboot.org/14656
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If a framebuffer is already configured by coreboot, libpayload's
MMU tables didn't mark its memory DMAable (unlike when libpayload
set up its own framebuffer memory).
BRANCH=none
BUG=chrome-os-partner:52826
TEST=depthcharge's recovery screen is not corrupted anymore on kevin
Change-Id: I228a861b3fdcf1298a3cfa0a054214c78ed55e70
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 889e8358a0f2f504abd9910549aa68f3992bb4e8
Original-Change-Id: I7ba79151ccc1eb605f82e1869a74b539a6be5e99
Original-Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/341092
Reviewed-on: https://review.coreboot.org/14685
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
BUG=chrome-os-partner:49249
TEST=Compiles and boots and detect USB storage
BRANCH=none
Change-Id: I9007399e1f785e6f1d2258225e3f7cc602053aed
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1db43f53973d2124e41186777caa829aa346ace3
Original-Change-Id: I943d19a3a7d785bd075073b57ba6388662d7df90
Original-Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/333311
Original-Commit-Ready: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/14659
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds a nyan libpayload config, that should fit all nyan devices.
Change-Id: I6b86a03054a7625534fd38ee6a21d3b91fb43589
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: https://review.coreboot.org/14473
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Move time functions and prototypes from libpayload.h to time.h.
In a similar manner to other c libary headers, this change makes
porting existing applications to libpayload easier.
Change-Id: I71e27c6dddde6e77e0e9b4d7be7cd5298e03a648
Signed-off-by: Stef van Os <stef.van.os@prodrive-technologies.com>
Reviewed-on: https://review.coreboot.org/14437
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
drivers/usb/xhci.c and drivers/usb/ehci.c both require arch/barrier.h.
barrier.h is present for x86, arm, and arm64, but not for mips. This
is generating a build error after enabling USB by default on libpayload.
I believe that this slipped through the buiders due to them not getting
cleaned fully. It was caught in the coverity scan and when setting up
a new build server.
Change-Id: Idd89409a048009c087ce2a787d96a1efd089157f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14391
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
There is a lot of generic code in the 8250 driver that should
be available for non-8250 systems with serial ports as well.
Change-Id: I67fcb12b5fa99ae0047b3cbf1815043d3919437e
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14371
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Most people use USB keyboards.
Change-Id: Ia7cf513059565db7b86190c4aae62d7a35392408
Signed-off-by: Marcel Meißner <mm-meissner@gmx.de>
Reviewed-on: https://review.coreboot.org/7540
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Since r is a pointer, memset(r, 0, sizeof(r)) would only zero the first
4 (or 8) bytes of the newly allocated struct align_region_t.
An alternative to this patch would be to use calloc, or introduce a new
zalloc (zeroed allocation; a single-element calloc) and use that.
Change-Id: Ic3e3487ce749eeebf6c4836e62b8a305ad766e7e
Found-by: Coverity (ID 1291160)
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/14244
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This allows to accommodate different platforms' default
configurations, memory configuration is fine tuned later during boot
process.
BUG=chrome-os-partner:51537
BRANCH=none
TEST=none yet, the full stack of patches boots fine on EVB
Change-Id: I39da4ce247422f67451711ac0ed5a5e1119ed836
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 97a9a71ade4df8a501043f9ae58463a3135e2a4f
Original-Change-Id: I39da4ce247422f67451711ac0ed5a5e1119ed836
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/332384
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/13914
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
- Copy each config in configs/ to the junit_config, update each,
in turn, and clean up when done. This avoids updating the saved
config files and creating dirty files in git.
- Use 'make olddefconfig' instead of 'yes "" | make oldconfig'
- Update clean target to remove junit_config file
- Update distclean target to remove junit.xml
Change-Id: Ib023eb3197f2d8806c73c9c18464157ce3de958f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14164
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add all the default options with:
for i in configs/*
do
cp $i .config
make savedefconfig
mv defconfig $i
done
This also switches to minimal config files instead of the full
configuration files that were previously checked in.
Change-Id: If18a32eca4df9e1dfeb0e212b652d972cea8e4b8
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14077
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
This will allow more payloads to use the standard linker script
instead of implementing their own.
Change-Id: Ie60120769829f427ceb722109d85859b61dbde31
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14074
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
_LDFLAGS+="foo" did not work in my shell (bash on Ubuntu 15.10),
so change it to _LDFLAGS="$_LDFLAGS foo". I'm mildly surprised
that this ever worked.
Change-Id: I59c10f34992240c6df2ec7f24aebc6daafb76493
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14076
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
MEMMAP_RAM_ONLY is not an architecture specific option,
hence move it out of the architecture specific menu.
Change-Id: Iaeef03ed8cbff930a580ad03b1e712087b48714e
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14071
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This is adding complexity to the code more than it saves
space, plus some of the tables could potentially be interesting
outside of the ChromeOS context.
Change-Id: I4bf24608f3e26d3b7871a5031ae8f03bc2c8c21f
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14070
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Bring defconfig and defconfig-tinycurses in sync, so that
defconfig and defconfig-tinycurses only differ in the selection
of the curses implementation.
Change-Id: I739c5122b5aaaa2681055c845905721a0b2a11c1
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14069
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
- Change the makefile command $(shell pwd) to $(CURDIR) to find the
current directory without going out to the shell.
Change-Id: I4890eba6129630acd2883b92de77308d39949443
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13967
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch ports the LZ4 decompression code that debuted in libpayload
last year to coreboot for use in CBFS stages (upgrading the base
algorithm to LZ4's dev branch to access the new in-place decompression
checks). This is especially useful for pre-RAM stages in constrained
SRAM-based systems, which previously could not be compressed due to
the size requirements of the LZMA scratchpad and bounce buffer. The
LZ4 algorithm offers a very lean decompressor function and in-place
decompression support to achieve roughly the same boot speed gains
(trading compression ratio for decompression time) with nearly no
memory overhead.
For now we only activate it for the stages that had previously not been
compressed at all on non-XIP (read: non-x86) boards. In the future we
may also consider replacing LZMA completely for certain boards, since
which algorithm wins out on boot speed depends on board-specific
parameters (architecture, processor speed, SPI transfer rate, etc.).
BRANCH=None
BUG=None
TEST=Built and booted Oak, Jerry, Nyan and Falco. Measured boot time on
Oak to be about ~20ms faster (cutting load times for affected stages
almost in half).
Change-Id: Iec256c0e6d585d1b69985461939884a54e3ab900
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/13638
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When CONFIG_LP_TIMER_RDTSC is enabled honor the TSC information
exported in the coreboot tables as the cpu_khz frequency. That
allows get_cpu_speed() not to be called which currently relies
on the 8254 PIT. As certain x86 platforms allow that device
to be optional or turned off for power saving reasons, allow
a path where get_cpu_speed() is no longer called. Additionally,
this approach also allows the libpayload to not duplicate logic
that already exists in coreboot.
BUG=chrome-os-partner:50214
BRANCH=glados
TEST=Confirmed in payload TSC frequency is honored instead of
using get_cpu_speed().
Change-Id: Ib8993afdfb49065d43de705d6dbbdb9174b6f2c4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13671
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
This fixes serial on rk3288.
Change-Id: I3dbf3cc165e516ed7b0132332624f882c0c9b27f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/13636
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
archive.h is a header file for the programs which need to parse an archive
created by 'archive' tool. See archive.h for the format description.
BUG=chromium:502066
BRANCH=tot
TEST=Tested on Glados
Change-Id: I2bee9d7c12b0e1bce1529dfef360c5fa4ce0872d
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/311201
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://review.coreboot.org/12734
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Update to use the CONFIG_LP_8250_SERIAL_CONSOLE instead of the removed
CONFIG_LP_8250_MMIO32_SERIAL_CONSOLE.
- CONFIG_LP_LZ4 and CONFIG_LP_PL011_SERIAL_CONSOLE are set to the
default values for these new config options.
CONFIG_LP_8250_MMIO32_SERIAL_CONSOLE was removed in
commit 4d5317e5 (libpayload: Remove redundant 8250 MMIO32 UART driver)
Change-Id: I97461c5e0c14075dcf8a35c96a0b0f1651e2e8e4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12654
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Update to use the CONFIG_LP_8250_SERIAL_CONSOLE instead of the removed
CONFIG_LP_8250_MMIO32_SERIAL_CONSOLE.
- CONFIG_LP_LZ4 and CONFIG_LP_PL011_SERIAL_CONSOLE are set to the
default values for these new config options.
CONFIG_LP_8250_MMIO32_SERIAL_CONSOLE was removed in
commit 4d5317e5 (libpayload: Remove redundant 8250 MMIO32 UART driver)
Change-Id: I2775c3676d5f458a4c31fe0c1d571bc2b9221a5c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12653
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change revives the path which was made inert by CL:308520. When
media == CBFS_DEFAULT_MEDIA, cbfs_get_file replaces it with a pointer
to a default media. Thus, get_cbfs_range does not set cbfs offset &
size from lib_sysinfo.
BUG=chrome-os-partner:47772
BRANCH=tot
TEST=Tested on Jerry and Glados
Change-Id: I012f7871336dd24b8eada5c96c4d72117921b0d2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 279ba344788b4ba85f500e6cfcca8199af6d0a89
Original-Change-Id: I7f0798881519026a23d0801d0a790332ab878ff0
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/313205
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/12583
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The more generic 8250 driver can handle both port-mapped and memory-
mapped 8250-compatible UARTs, with different register sizes. Thus, a
separate driver for MMIO32 is not needed.
The generic 8250 driver was tested to work for both output and input,
on Apollolake SoC, which only presents an MMIO32 UART.
Change-Id: Idab766588ddd097649a37de92394b0078ecc660a
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: https://review.coreboot.org/12524
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
during shutdown
DWC2 UDC controller always requires an active packet to be present in
EP0-OUT to ensure proper operation of control plane. Thus, during
shutdown ignore EP0-OUT for queue empty check if only 1 packet is
present.
BUG=b:24676003
BRANCH=None
TEST=Compiles successfully. "fastboot reboot-bootloader" reboots
device without timeout in udc shutdown.
Change-Id: Iafe46c80f58c4cd57f8d58f060d805b603506bbd
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4e7c27d849c0411aae58e60a24d8170a27ab8485
Original-Change-Id: Ifa493ce0e41964ee7ca8bb3a1f4bb8726fa11173
Original-Signed-off-by: Furquan Shaikh <furquan@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/311257
Original-Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Original-Tested-by: Furquan Shaikh <furquan@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12413
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Don't hard code the PDCurses version number in every file
added to the object list.
Change-Id: Ic2e9230b7e3089c60dd7f442e3ea7baffb4aa400
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/12397
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Existing Intel xHCI controllers require a delay of 1 ms,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.
Verified CherryView / Braswell platforms go through over
1000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang in depthcharge.
BRANCH=None
BUG=None
TEST=Verified CherryView / Braswell platforms go through
over 1000 warm reboot cycles, without any xHCI reset hang
in depthcharge.
Change-Id: I8eff5115ca52738bdcf8bc65fbfb2a5f60a0abe1
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3e7ea70df36e3bf35a6ee1297640900ee76bfdac
Original-Change-Id: Id681a19d0eedb0e2c29e259c5467bcde577e3460
Original-Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/310022
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/12325
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
enqueue_packet already runs start_ep_transfer, which enqueues the next
job. It's pretty much guaranteed that the port will look busy.
BUG=none
BRANCH=none
TEST=no spurious ep 0-0 busy messages
Change-Id: I9cbfa7b51dd37564262295ddbcdd0755da40c05b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8997dbd78dc363334f4e22eaa61f25de1449ffba
Original-Change-Id: I8a39713fc1d6f16b80284e0f21dc95685716a9b7
Original-Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/308763
Original-Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Original-Reviewed-by: yunzhi li <lyz@rock-chips.com>
Reviewed-on: http://review.coreboot.org/12259
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
hexdump() now takes a pointer instead of an int-containing-an-address.
BUG=none
BRANCH=none
TEST=building with USB_DEBUG works
Change-Id: Idd0c43031a212c8f3b6489f533c488805d98d6a9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8660f6091bb124eeabe73302e8c7f1a8e46324f1
Original-Change-Id: I266efcb8b939d6da104ad05a3e79a78065c60beb
Original-Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/308762
Original-Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Original-Reviewed-by: yunzhi li <lyz@rock-chips.com>
Reviewed-on: http://review.coreboot.org/12258
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
CBFS requests were always fulfilled using the CBFS specified in
cbtables. That's a great policy when default requests are sought, but
not so great when the user deliberately asked for something else.
So check if they want default CBFS media information, otherwise ignore
cbtables data.
BUG=chromium:445938
BRANCH=none
TEST=none
Change-Id: I01b63049eebfba6f467808ac84ef77385840c204
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 621c916ab14c0de4bae3dde09c05060c4f3c63c5
Original-Change-Id: Ia4a8848fd7db9d9a2bf9f5c226566fe3936ff543
Original-Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/308520
Original-Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12232
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We found that some SanDisk Cruizer Glide CZ60 sticks (confirmed on 16GB
and 64GB versions) have a problem responding to our first GET_MAX_LUNS
request right after they received their SET_CONFIGURATION. They will
continually return a NAK until the host gives up (which is 2
user-noticable seconds for us). Adding a small delay of about 15us seems
to be enough to fix the issue, but let's do 50 to be save.
Confirmed with both MT8173 and Intel LynxPoint XHCI controllers.
BRANCH=None
BUG=chrome-os-partner:45473
TEST=No notable delay before detecting stick on Oak and Falco.
Change-Id: Ib03944d6484de0ccecbb9922d22666f54c9d53dd
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 589f19a901275fb8b00de4595763a7d577bed524
Original-Change-Id: I95c79fe40d3ad79f37ce2eb586836e5de55be454
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/308980
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/12229
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Change Ie54699162 changed a structure's name and field names and we
didn't notice. Adapt.
BUG=none
BRANCH=none
TEST=building with UDC_DWC2 works
Change-Id: I592ebc29b2a08a23e6dbc9d2186807cbbbbca330
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3dda8ad5ffc36593d8b8fd6664a7f9b4816f0f93
Original-Change-Id: I4a065de0f4045a01bef1dc9fbb2e0578b5508518
Original-Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/308791
Original-Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/12228
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change allows libpayload to read cbfs offset and size from sysinfo.
Legacy way of locating cbfs reagion is still supported in case sysinfo
doesn't store the offset and the size.
BUG=none
BRANCH=master
TEST=tested on samus and smaug
Change-Id: I86434fd249467e7c90d59d6b82f0e6c514bc2d05
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 548a74b7a0758c3f9ba6809425d0fb9c6a5e9d7c
Original-Change-Id: I190d5545a65228483204bf1aa1cbf5a80db31ae0
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/296993
Original-Commit-Ready: Daisuke Nojiri <dnojiri@google.com>
Original-Tested-by: Daisuke Nojiri <dnojiri@google.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11557
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
get_image_dimension returns the width or height of the image projected on
canvas.
This is necessary for example when two images of different lengths have to
be placed side by side in the center of the canvas and the widths of the
images must be adjusted according to the height.
BUG=chromium:502066
BRANCH=tot
TEST=Tested on Samus
Change-Id: I119c83891f48046e888b6b526e63348e74f8b77c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: d1a97f0492eb02f906feb5b879b7b43518dfa4d7
Original-Change-Id: Ie13f7994d639ea1556f73690b6b6b413ae64223c
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/304113
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11929
Tested-by: build bot (Jenkins)
Julius Werner