And include the new, split out version in drivers/keyboard.c and
drivers/usb/usbhid.c. Those files were including curses.h just for those
definitions, but the include path was only fixed up to to point to the
libpayload versions of those files if one of the variants of curses was
compiled in. If neither was, gcc would fall back to the system version of that
header which is wrong.
Change-Id: I8c2ee0baf5f0702bd8c713c8dd4613a4bb269ce5
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2762
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
By including the heap in the bss output section the size is accounted
for in a elf PT_LOAD segment. Without this change the heap wasn't being
put into a PT_LOAD segment. The result is a nop w.r.t. functionality,
but readelf and company will have proper MemSiz fields.
Change-Id: Ibfe9bb87603dcd4c5ff1c57c6af910bbba96b02b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2750
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There is a plan to utlize rmodules for loading ramstage as a
relocatable module. However, the rmodule header may change.
In order to provide some wiggle room for changing the contents
of the rmodule header add some padding. This won't stop the need
for coordinating properly between the romstage loader that may be
in readonly flash and rmodule header fields. But it will provide
for a way to make certain assumptions about alignment of the
rmodule's program when the rmodule is compressed in the flash.
Change-Id: I9ac5cf495c0bce494e7eaa3bd2f2bd39889b4c52
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2749
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Haswell's BCLK is fised at 100MHz like Sandy/Ivy. Add Haswell's model
to the switch statement.
Change-Id: Ib9e2afc04eba940bfcee92a6ee5402759b21cc45
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2747
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Rather than have to repeat this bit in every mainboard.
Also, remove the reset of the RTC power status from here.
We had done this in TOT for current platforms but did not
carry it back to emeraldlake2 where this branched from.
If we clear the status here then we don't get an event
logged later which can be important for the devices that
do not have a CMOS battery.
Change-Id: Ia7131e9d9e7cf86228a285df652a96bcabf05260
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2683
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
A rmodule is short for relocation module. Relocaiton modules are
standalone programs. These programs are linked at address 0 as a shared
object with a special linker script that maintains the relocation
entries for the object. These modules can then be embedded as a raw
binary (objcopy -O binary) to be loaded at any location desired.
Initially, the only arch support is for x86. All comments below apply to
x86 specific properties.
The intial user of this support would be for SMM handlers since those
handlers sometimes need to be located at a dynamic address (e.g. TSEG
region).
The relocation entries are currently Elf32_Rel. They are 8 bytes large,
and the entries are not necessarily in sorted order. An future
optimization would be to have a tool convert the unsorted relocations
into just sorted offsets. This would reduce the size of the blob
produced after being processed. Essentialy, 8 bytes per relocation meta
entry would reduce to 4 bytes.
Change-Id: I2236dcb66e9d2b494ce2d1ae40777c62429057ef
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2692
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The acpi_fill_mcfg() was still using ivy/sandy PCI device ids which Hawell
obviously doesn't have. This resulted in an empty MCFG table. Instead of
relying on PCI device ids use dev/fn 0/0 since that is where the host
bridge always resides. Additionally remove the defines for the IB and SB
pci device ids. Replace them with mobile and ult Haswel device ids and
use those in the pci driver tables for the northbridge code.
Booted to Linux and noted that MCFG was properly parsed.
Change-Id: Ieaab2dfef0e9daf3edbd8a27efe0825d2beb9443
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2748
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The SMM handler resides in the TSEG region which is far above
CONFIG_RAM_TOP (which is the highest cacheable address) before
MTRRs are setup. This means that calling initialize_cpus() before
performing MTRR setup on the BSP means the SMM handler is copied
using uncacheable accesses.
Improve the SMM handler setup path by enabling performing MTRR setup on
for the BSP before the call to initialize_cpus(). In order to do this
the haswell_init() function was split into 2 paths: BSP & AP paths.
There is a cpu_common_init() that both call to perform similar
functionality. The BSP path in haswell_init() then starts the APs using
intel_cores_init(). The AP path in haswell_init() loads microcode and
sets up MTRRs.
This split will be leveraged for future support of bringing up APs in
parallel as well as adhering to the Haswell MP initialization
requirements.
Change-Id: Id8e17af149e68d708f3d4765e38b1c61f7ebb470
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2746
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The configure_mca() function was hard coding the number of
banks the cpu supported. Query this dynamically so that it
no longer clears only 7 banks.
Change-Id: I33fce8fadc0facd1016b3295faaf3ae90e490a71
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2745
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This just moves the definiton of CORE_THREAD_COUNT_MSR so
that future code can utilize it.
Change-Id: I15a381090f21ff758288f55dc964b6694feb6064
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2744
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This commit adds support for using the SMM modules for haswell-based
boards. The SMI handling was also refactored to put the relocation
handler and permanent SMM handler loading in the cpu directory. All
tseg adjustment support is dropped by relying on the SMM module support
to perform the necessary relocations.
Change-Id: I8dd23610772fc4408567d9f4adf339596eac7b1f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2728
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We're happy to announce coreboot support for the "Stout"
Chromebook, a.k.a Lenovo X131e Chromebook.
Change-Id: I9b995f8d0dd48e41c788b7c3d35b4fac5840e425
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2636
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is mostly a copy of Whitetip Mountain 1 with specific GPIO
map for this Customer Reference Board (CRB).
This mainboard currently has basic funcionality and is able to
boot a Linux Kernel but many of the new Haswell ULT specific
devices are not yet enabled.
Change-Id: I999452d86f00a2c245fa39b1b76080f6a3b1e352
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2725
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Some initialization steps were done twice
- One step was missing for Panther Point HDA
- Added a 1ms delay after reset
- Increased timeout to 1ms for all codec operations
Change-Id: Ib751f1a16ccd88ea2fbbb2a10737f76277574026
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2518
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Haswell CPUs require a FIT table in the firmware. This commit
adds rudimentary support for a FIT table. The number of entries
in the table is based on a configuration option. The code only
generates a type 0 entry. A follow-on tool will need to be developed
to populate the FIT entries as well as checksumming the table.
Verified image has a FIT pointer and table when option is selected.
Change-Id: I3a314016a09a1cc26bf1fb5d17aa50853d2ef4f8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2642
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There was a mix of setup code sprinkled across the various components:
southbridge code in the northbridge, etc. This commit reorganizes the
code so that northbridge code doesn't initialize southbridge components.
Additionally, the calling dram initialization no longer calls out to ME
code. The main() function in the mainboard calls the necessary ME
functions before and after dram initialization.
The biggest change is the addition of an early_pch_init() function
which initializes the BARs, GPIOs, and RCBA configuration. It is also
responsible for reporting back to the caller if the board is being
woken up from S3. The one sequence difference is that the RCBA config
is performed before claling the reference code.
Lastly the rcba configuration was changed to be table driven so that
different board/configurations can use the same code. It should be
possible to have board/configuration specific gpio and rcba
configuration while reusing the romstage code.
Change-Id: I830e41b426261dd686a2701ce054fc39f296dffa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2681
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Lots of things are still placeholder and need work.
Due to the useful GPIOs being run to either the EC or the SIO1007
I have hard coded developer mode on and recovery mode off.
Change-Id: I4c308bd90db03ac5bffdfde566e5adbbaabac632
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2724
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Certain SATA devices claim to support SATA 6 Gbps, but in fact have
bugs. For these devices, add a config option to force the SATA link
speed to something other than default.
Change-Id: I2dc1793cd58771298a392345162d39d20eb0afbb
Signed-off-by: Shawn Nematbakhsh <shawnn@google.com>
Reviewed-on: http://review.coreboot.org/2765
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables power management and clock gating on XHCI.
Change-Id: I124ea6c5aca034b7ec4b5286d971c2adfce25c88
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2761
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
objcopy -B provides symbols of the form _binary_<name>_(start|end|size).
However, the _size variant is an absoult symbol. If one wants to
relocate the smi loading the _size symbol will be relocated which is
wrong since it is suppose to be a fixed size. There is no way to
distinguish symbols that shouldn't be relocated vs ones that can.
Instead use the _start and _end variants to determine the size.
Change-Id: I55192992cf36f62a9d8dd896e5fb3043a3eacbd3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2760
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The bd82x6x requires some additional setting on S3/S4 entry.
Change-Id: I24489ab94dd7cd5a4a64044f25153f5b01a45b77
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2759
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add the PCH function to SMM for follow-on SMM patches that
require these functions.
Change-Id: I7f3a512c5e98446e835b59934d63a99e8af15280
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2758
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The SMRR takes precedence over the MTRR entries. Therefore, if the TSEG
region is setup as cacheable through the MTTRs, accesses to the TSEG
region before SMM relocation are cached. This allows for the setup of
SMM relocation to be faster by caching accesses to the future TSEG
(SMRAM) memory.
MC MAP: TOM: 0x140000000
MC MAP: TOUUD: 0x18f600000
MC MAP: MESEG_BASE: 0x13f000000
MC MAP: MESEG_LIMIT: 0x7fff0fffff
MC MAP: REMAP_BASE: 0x13f000000
MC MAP: REMAP_LIMIT: 0x18f5fffff
MC MAP: TOLUD: 0xafa00000
MC MAP: BGSM: 0xad800000
MC MAP: BDSM: 0xada00000
MC MAP: TESGMB: 0xad000000
MC MAP: GGC: 0x209
TSEG->BGSM:
PCI: 00:00.0 resource base ad000000 size 800000 align 0 gran 0 limit 0 flags f0004200 index 4
BGSM->TOLUD:
PCI: 00:00.0 resource base ad800000 size 2200000 align 0 gran 0 limit 0 flags f0000200 index 5
Setting variable MTRR 0, base: 0MB, range: 2048MB, type WB
Setting variable MTRR 1, base: 2048MB, range: 512MB, type WB
Setting variable MTRR 2, base: 2560MB, range: 256MB, type WB
Adding hole at 2776MB-2816MB
Setting variable MTRR 3, base: 2776MB, range: 8MB, type UC
Setting variable MTRR 4, base: 2784MB, range: 32MB, type UC
Zero-sized MTRR range @0KB
Allocate an msr - basek = 00400000, sizek = 0023d800,
Setting variable MTRR 5, base: 4096MB, range: 2048MB, type WB
Setting variable MTRR 6, base: 6144MB, range: 256MB, type WB
Adding hole at 6390MB-6400MB
Setting variable MTRR 7, base: 6390MB, range: 2MB, type UC
MTRR translation from MB to addresses:
MTRR 0: 0x00000000 -> 0x80000000 WB
MTRR 1: 0x80000000 -> 0xa0000000 WB
MTRR 2: 0xa0000000 -> 0xb0000000 WB
MTRR 3: 0xad800000 -> 0xae000000 UC
MTRR 4: 0xae000000 -> 0xb0000000 UC
I'm not a fan of the marking physical address space with MTRRs as being
UC which is PCI space, but it is technically correct.
Lastly, drop a comment describing AP startup flow through coreboot.
Change-Id: Ic63c0377b9c20102fcd3f190052fb32bc5f89182
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2690
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Devoutly to be wish'd. To die,—to sleep;—
To sleep! perchance to dream:—ay, there's the rub;
For in that sleep of death what dreams may come,
(Since who could argue with William Shakespeare?)
Change-Id: I4e4c617dcd3ede81a0abbe16f9916562d24fa8ce
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/2733
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This is the same change as made to Persimmon with
change-id I44f22:
http://review.coreboot.org/#/c/2592/
Change-Id: I5184df8deb7b5d2e15404d689c16c00493eb01aa
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2736
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same chagne as made to Persimmon in
Change-ID If8d86f:
http://review.coreboot.org/#/c/2726/
Change-Id: Id560ea85a38f73aaba2c35447bbce46bd9c0d0dd
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2741
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same change as made to Persimmon in
Change-ID If8d86f:
http://review.coreboot.org/#/c/2726/
Change-Id: Iae70c3d0af1cdaca31b206ad6daba4d38ee6b780
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2742
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same change as made to Persimmon in
Change-ID If8d86f:
http://review.coreboot.org/#/c/2726/
Change-Id: Iff594d4a3493531561eb25d1cceeb97bcefde424
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This is the same change as made to Persimmon with
change-id I44f22:
http://review.coreboot.org/#/c/2592/
Change-Id: Ie36b60973c6a5f9076bb55c8f451532711a2f8a8
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2737
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The _OSC method is used to tell the OS what capabilities
it can take control over from the firmware. This method
is described in chapter 6.2.9 of the ACPI spec v3.0.
The method takes 4 inputs (UUID, Rev ID, Input Count,
and Capabilities Buffer) and returns a Capabilites
Buffer the same size as the input Buffer. This Buffer
is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control
Dword. The OS will request control of certain
capabilities and the firmware must grant or deny control
of those features. We do not want to have control over
anything so let the OS control as much as it can.
The _OSC method is required for PCIe devices and dmesg
checks for its existence and issues an error if it is
not found.
This is the same change made to Persimmon with Change-ID
I149428:
http://review.coreboot.org/#/c/2684/
Change-Id: If6dd1a558d9c319d9a41ce63588550c8e81e595f
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2738
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The _OSC method is used to tell the OS what capabilities
it can take control over from the firmware. This method
is described in chapter 6.2.9 of the ACPI spec v3.0.
The method takes 4 inputs (UUID, Rev ID, Input Count,
and Capabilities Buffer) and returns a Capabilites
Buffer the same size as the input Buffer. This Buffer
is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control
Dword. The OS will request control of certain
capabilities and the firmware must grant or deny control
of those features. We do not want to have control over
anything so let the OS control as much as it can.
The _OSC method is required for PCIe devices and dmesg
checks for its existence and issues an error if it is
not found.
This is the same change made to Persimmon with Change-ID
I149428:
http://review.coreboot.org/#/c/2684/
Change-Id: I2701d915338294bdade2ad334b22a51db980892e
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2739
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The _OSC method is used to tell the OS what capabilities
it can take control over from the firmware. This method
is described in chapter 6.2.9 of the ACPI spec v3.0.
The method takes 4 inputs (UUID, Rev ID, Input Count,
and Capabilities Buffer) and returns a Capabilites
Buffer the same size as the input Buffer. This Buffer
is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control
Dword. The OS will request control of certain
capabilities and the firmware must grant or deny control
of those features. We do not want to have control over
anything so let the OS control as much as it can.
The _OSC method is required for PCIe devices and dmesg
checks for its existence and issues an error if it is
not found.
This is the same change made to Persimmon with Change-ID
I149428:
http://review.coreboot.org/#/c/2684/
Change-Id: Iaf7b8153cec4d730efbceae3e6957d2904b8fae4
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2740
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These enables are hidden behind IOBP for some reason.
Boot to linux with SDIO disabled and see that
the SDIO driver does not load and crash the system.
Change-Id: Icfbfa117e9e57a51d32db7f6366a9d0d790adcf0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2695
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Paul points out that some people like 1024*1024, others like
1048576, but in any case these are all open to typos.
Define KiB, MiB, GiB, and TiB as in the standard so people can use them.
Change-Id: Ic1b57e70d3e9b9e1c0242299741f71db91e7cd3f
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2769
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
It's possible that TOUUD can be 4GiB in a small physical memory
configuration. Therefore, don't add a 0-size memory range resouce
in that case.
Change-Id: I016616a9d9d615417038e9c847c354db7d872819
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2691
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is a bit of a hack but it's very handy. It compiles in your static.c
and then shows what coreboot would see when it is run. It uses your static.c
and functions pulled from src/device/device_util.c.
I've already used it to debug problems with the snow device tree.
I'm waiting someone to tell me this is already written :-)
Change-Id: Ia8c8a5d08d8757bec49eaf70473efa701bc56581
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2767
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
One might wonder what a board named 'build' does. Rename the file to
build-snow. The fact that it is in a directory with google in the name
should be enough to identify the vendor.
Change-Id: I0b473cdce67d56fc6b92032b55180523eb337d66
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2766
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This should help avoid wrong 3rdparty commit ids
creeping in.
Change-Id: I2134ad1d3ad0237ef3f12baf4d4aafb02009e7bc
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2768
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The Link native graphics commit 49428d84 [1]
Add support for Google's Chromebook Pixel
was missing some of the higher level bits, and hence could not be
used. This is not new code -- it has been working since last
August -- so the effort now is to get it into the tree and structure
it in a way compatible with upstream coreboot.
1. Add options to src/device/Kconfig to enable native graphics.
2. Export the MTRR function for setting variable MTRRs.
3. Clean up some of the comments and white space.
While I realize that the product name is Pixel, the mainboard in the
coreboot tree is called Link, and that name is what we will use
in our commits.
[1] http://review.coreboot.org/2482
Change-Id: Ie4db21f245cf5062fe3a8ee913d05dd79030e3e8
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2531
Tested-by: build bot (Jenkins)
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This is the same change as made to Persimmon with
change-id I44f22:
http://review.coreboot.org/#/c/2592/
Change-Id: I9017a7619b3b17e0e95ad0fe46d0652499289b00
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2735
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
For google/stout binaries
Apparently the actual marker got lost in the rebase / change of the
commit message.
Change-Id: I4f18b9ddba326988b58f2595c0025a113feb0d68
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2734
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Pins 78-85 are set to GPIO after power on or reset. To enable
UART B the pins must be redirected to it.
Look at W83627DHG databook version 1.4 page 185 Chip
(global) Control Register CR2C.
Change-Id: I12b094a60d9c5cb2447a553be4679a4605e19845
Signed-off-by: Wolfgang Kamp <wmkamp@datakamp.de>
Reviewed-on: http://review.coreboot.org/2626
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
Change-Id: If8d86f959822d528c44ab011a851659d486289b5
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2726
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The _OSC method is used to tell the OS what capabilities
it can take control over from the firmware. This method
is described in chapter 6.2.9 of the ACPI spec v3.0.
The method takes 4 inputs (UUID, Rev ID, Input Count,
and Capabilities Buffer) and returns a Capabilites
Buffer the same size as the input Buffer. This Buffer
is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control
Dword. The OS will request control of certain
capabilities and the firmware must grant or deny control
of those features. We do not want to have control over
anything so let the OS control as much as it can.
The _OSC method is required for PCIe devices and dmesg
checks for its existence and issues an error if it is
not found.
Change-Id: I1494285def7440972f0549b7cb73eb94dafc72c2
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2684
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This wasn't previously spotted because the printk's were correct.
However if one needed to get the value of the BDSM or BGSM register
the value would reflect the other register's value.
Change-Id: Ieec7360a74a65292773b61e14da39fc7d8bfad46
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2689
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This commit updates the Lynx Point resource reservations before
the coreboot allocator assigns resources. There is no need to mark
anything as subtractive decode because there are no devices/buses
linked to the LPC device.
The I/O range reservations consists of claiming the first 4KiB
of I/O space. The PMBASE, GPIOBASE, and LPC generic I/O decode
ranges are checked against the default claimed range. If those
ranges overlap or fall outside of the default range then those
resources are added.
The MMIO range reservations consist of claiming everything from
the I/O APIC to 4GiB. The RCBA and the LPC Generic Memory range
register are then conditionally added if they fall outside of
the default MMIO range.
Change-Id: I0f560a03814a2b15961fdbe61e4164cd54cff7a5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2682
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Gabe Black