These values were originally hard-coded in the AMD MCT wrapper.
Change-Id: I12056d38d5348e70a44c192385e22e715e207792
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/8454
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
On x86, change the type of the address parameter in
read8()/read16/read32()/write8()/write16()/write32() to be a
pointer, instead of unsigned long.
Change-Id: Ic26dd8a72d82828b69be3c04944710681b7bd330
Signed-off-by: Kevin Paul Herbert <kph@meraki.net>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/7784
Tested-by: build bot (Jenkins)
A set of pins can be configured for GPIO or (parallel) PCI bridge use.
When requested configuration is 0:14.4 enabled, register programming
must be done before attempting to enumerate devices behind the bridge.
When requested configuration is 0:14.4 disabled, we must not even
temporarily enable pins for PCI use to avoid spurious GPIO state changes.
As our PCI subsystem currently does not configure visible PCI bridges
that are marked disabled, we cannot mark 0:14.4 disabled just yet but
need to handle pcengines/apu1 as a special case.
Drop related dead code.
Change-Id: I8644ebae43b33121ef2a7ed30f745299716ce0df
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8329
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Change-Id: I92e6e7f1292f66642aa0336064a4eccba104dd08
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/5101
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
The PCI id defaults to 1106,3230 -> via chrome 9 ...
Tested on the board.
Change-Id: I5ad91faec9c97f34c8ca48eee9198237e9ea8336
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/8177
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This resolves an issue on Shanghai dual CPU configurations where
the APs on node 0 would not start. Single CPU configurations are
unaffected by this issue.
TEST: Booted KFSN4-DRE with dual Opteron 8389 CPUs and verified
proper BSP/AP start and microcode patch levels.
Change-Id: I0f5d4e0e356c6bd64e324b4399ef43b400ecab0c
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/8397
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Include microcode updates in CBFS for every CPU revision the platform
can support, as changing to different CPU revision should not require
a coreboot rebuild.
This increases CBFS usage from 2 kB to 14 kB.
Change-Id: I6bf90221a688f1a54e49641ce3ba378c5bf659f9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4521
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Test:
Single Opteron 2419 with 1GB RAM in slot A1
Booted Ubuntu Linux 14.04 and verified all 6 cores were visible
Brief stress test of all 6 cores simultaneously
Verified proper ACPI power states for all 6 cores
Change-Id: I1e598e36f9eaed5ba8a18b9c62ceedee16870f15
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/8311
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Status:
Tested with KFSN4-DRE PCB v1.04G
Booted Ubuntu Linux 14.04 and all onboard peripherals appear to work.
Dual Opteron 8347 CPUs tested with 8GB RAM (4GB per bank).
Dual Opteron 8356 CPUs tested with 1GB RAM in slot A1.
AMD PowerNow! functions correctly via ACPI.
Video, network, USB, SATA, and serial have received thorough testing.
Tested with KFSN4-DRE PCB v1.05G
Single Opteron 2419 CPU tested with 1GB RAM in slot A1.
Booted to PXE configuration menu; not tested further.
Known issues:
RAM initialization is a bit flaky with multiple high-density modules;
this could be a generic MCT training issue but is probably bad hardware.
The XGI Volari option ROM crashes SeaBIOS v1.7.5, but the video device
works after Linux boots and initializes the device.
Suspend/resume functions at the S1 level but sometimes hangs on resume.
Wake on LAN can be flaky; the strap(s) needed to have WoL work on power
application were not physically installed by ASUS so the board needs to
boot at least once after power application before it will work.
Change-Id: I0709f822eea8ed877f55db9443143028a5400472
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/8270
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Because we had no stack on romcc boards, we had a separate, not as
powerful clone of printk: print_*. Back in the day, like more than
half a decade ago, we migrated a lot of boards to printk, but we never
cleaned up the existing code to be consistent. instead, we worked around
the problem with a very messy console.h (nowadays the mess is hidden in
romstage_console.c and early_print.h)
This patch cleans up the mainboard code to use printk() on all non-ROMCC
boards.
Change-Id: I2383f24343fc2041fef4af65d717d754ad58425e
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/8111
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
These comments are left over and are not relevent in the coreboot
code, but created a new section titled "Release Content" in the
doxygen documentation produced by the coreboot code. In an effort
to clean up the output, I'm removing these doxygen comments.
Change-Id: I4d7be3313a2ab6c140b4f3afe70dffc4abba7bca
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/8069
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Use 'delay.h' header rather than directly including 'delay.c'
source. N.B. Some amdfam10 and K8 boards are not included in
this changeset since unrelated issues are woven in there.
Change-Id: Ibc0c0e560d8eedaf5c3150f95ba72fe5dd8d6f3a
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/8086
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Fix system include paths to be consistent. Chipset support is
part of the Coreboot 'system' and hence 'non-local' (i.e., in
the same directory or context). One possible product of this, is
to perhaps allow future work to do pre-compiled headers (PCH) on
the buildbot for faster build times. However, this currently just
makes mainboard's consistent.
Change-Id: I2f3fd8a3d7864926461c960ca619bff635d7dea5
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/8085
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
- Remove types from the param declarations.
- list needed to be uppercase.
Change-Id: I8b9ed78908e5d3e1d99e7ba2ea9013be109b8e27
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/8072
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Remove PeiServices param for OemInitEarly - it doesn't exist in the
function.
Change-Id: I338aeb4128126f6e541815dc09bf8d23678081c8
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/8073
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
- Move @def BIOS_SIZE description to the next line
- SB_GEN2 changed to SB_GPP_GEN2
- Move the SIO_HWM_BASE_ADDRESS description to the next line
Change-Id: Ia3496b0108484f557627304553461932a100dfa5
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/8071
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
We should potentially provide an OEM platform hook to manipulate parameters
around any entry point to AGESA. Use structure for such ops to avoid weak
functions and lots of empty function stubs.
Change-Id: I99bf7de8a1e2f183399d2216520a45d0c24fd64c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7824
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
It does not really matter if we continue or return after a failed
assertion, system configuration is invalid anyway.
Change-Id: I5ba47ee3fd6c5ff97b9229f8bfc9db08873b08ca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7823
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
These are not wrappers for AGESA as they do not enter vendorcode at all.
We expect most of the added fixme.c file to be written without use of AMDLIB.h
and parts relocated as northbridge enable_resources().
Change-Id: Iba6d59e2a7672349208e9a65fcd2cb1094ab7d50
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7815
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
This one is special because qemu is really far from anything real but
shares some common features.
Change-Id: Ia1631611724a074780e1fece50166730b2ee94ae
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6939
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
NOTE: For fam12 and fam14 ASSERT() is defined empty so execution may
fall through critical failures.
Change-Id: Ifef65d749d340f1df3a43b5fcb38c4315ef944e8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7154
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
GPP config from devicetree.cb is not implemented for fam15tn/fam16kb.
Also only for asus/f2a85-m the configuration value matched the actual
programming.
Change-Id: Ic7a9aa1360f4ba35d202f3f7dd1fc3c20a52dde0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7600
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
There were instances of unneeded arch/hlt.h includes,
various hlt() calls that weren't supposed to exit (but
might have) and various forms of endless loops around
hlt() calls.
All these are sorted out now: unnecessary includes are
dropped, hlt() is uniformly replaced with halt() (except
in assembly, obviously).
Change-Id: I3d38fed6e8d67a28fdeb17be803d8c4b62d383c5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/7608
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The F2A85-M LE has less DRAM slots and needs different settings.
Additionally, the audio codec verb table is different.
Change-Id: I0e13c91fc924f4f9eac534fd13d57830654dd0aa
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/7356
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
The ASUS F2A85-M has a keyboard controller, serial and parallel port
and thus is not legacy free at all.
Setting LEGACY_FREE causes some early bootup serial debug messages
to be lost.
Change-Id: Ibba38826e2f863c6e490e52bd5854e5dc0b6a357
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/7480
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
