These typos were found through manual review and grep.
Change-Id: Ia5a9acae4fbe2627017743106d9326a14c99a225
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/22525
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each rambi variant has a different USB port config.
Port data currently available for only candy and squawks;
other variants to be added once data obtained.
Change-Id: If7ce3d135d6ffe53ab1566d5258d01b052ac47f4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Light sensor isn't used and ACPI already removed, so disable
I2C5 bus interface as well.
Disable I2C6 for devices without a touchscreen
Change-Id: Ib0e041ae9131615ef1140bad064de5aae91f8ee4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Instead of defining SIO_EC_ENABLE_PS2K by default for all boards and
doing an undef in variant/onboard.h, move the definition of
SIO_EC_ENABLE_PS2K to variant/onboard.h. This avoids dependency
between different *.asl files.
Change-Id: I83e4ce42a594e952a443c618d7ef9840113027b9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18965
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Some variants need the internal pull resistor on GPIO_SSUS_40
set explicitly to pull down rather than disabling the pull,
in order for the ram-id to be read correctly via GPIO.
Correct this by adding a function to enable and set the internal pull
and define its use as needed in the board's variant.h.
Chromium source:
branch: firmware-gnawty-5216.239.B
/src/soc/intel/baytrail/baytrail/gpio.h#418
/src/mainboard/google/gnawty/romstage.c#60
Test: boot 4GB Candy board and observe correct RAM id, amount detected
Change-Id: I8823c27385f4422184b5afa57f6048f7ff2a25ab
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18309
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add new ChromeOS devices banjo, candy, clapper, glimmer, gnawty,
heli, kip, orco, quawks, squawks, sumo, swanky, and winky using
their common reference board (rambi) as a base.
Chromium sources used:
firmware-banjo-5216.334.B 32ec493 [chromeos: vboot_loader: Set...]
firmware-candy-5216.310.B 519ff11 [baytrail: Preserve VbNv around...]
firmware-clapper-5216.199.B 80d55e3 [baytrail: add code for...]
firmware-glimmer-5216.198.B fae0770 [baytrail: add code for...]
firmware-gnawty-5216.239.B 952adb7 [Gnawty/Olay: Add 2nd source...]
firmware-heli-5216.392.B f1f3604 [helis: Lock ME / TXE section...]
firmware-kip-5216.227.B db3c5d9 [kip: update spd for for MT41K256M16*]
firmware-orco-5216.362.B 76f1651 [Orco: Adjust rx delay for norm.]
firmware-quawks-5216.204.B edb60c9 [Quawks: Update SPD data]
firmware-squawks-5216.152.B c6573dc [Squawks: Update SPD data]
firmware-sumo-5216.382.B c62b6f23 [Ninja, Sumo: Add SPD source...]
firmware-swanky-5216.238.B 233b2a7 [Swanky: update SPD table]
firmware-winky-5216.265.B ce91ffc [Add to support HT Micron...]
The same basic cleanup/changes are made here as with the initial BYT
variant commit:
- remove unused ACPI trackpad/touchscreen devices
- correct I2C addresses in SMBIOS entries
- clean up comment formatting
- remove ACPI device for unused light sensor
- switch I2C ACPI devices from edge to level triggered interrupts,
for better compatibility/functionality (and to be consistent
with other recently-upstreamed ChromeOS devices)
- Micron 2GB SPD file for kip with updated values renamed to distinguish
from same file used by other boards
Change-Id: Ic66f9b539afb5aff32c4c1a8563f6612f5a2927c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18164
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Combine existing boards google/enguarde and google/ninja using
their common reference board google/rambi as a baseboard.
Variants contain board specific data:
- DPTF ACPI components
- I2C ACPI devices
- RAM config / SPD data
- devicetree config
- GPIOs
- board-specific HW components (e.g., LAN)
Additionally, some minor cleanup/changes were made:
- remove unused ACPI trackpad/touchscreen devices
- correct I2C addresses in SMBIOS entries
- clean up comment formatting
- remove ACPI device for unused light sensor
- switch I2C ACPI devices from edge to level triggered interrupts,
for better compatibility/functionality (and to be consistent
with other recently-upstreamed ChromeOS devices)
The existing enguarde and ninja boards are removed.
Variant setup modeled after google/auron
Change-Id: Iae7855af9a224fd4cb948b854494e39b545ad449
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18129
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
