Update Touchscreen GPIO to use the correct GPIO 90. GPIO 32 was a
copy/paste from dalboz and corresponds to the FP PWR EN on trembyle
platforms.
BUG=b:292656388
TEST=build/boot morphius
Change-Id: Ia6cdbe9195535093e68dbafedaddb70aaf73da88
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76747
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Set the cs_pi_start_high_in_ect if the DUT is using one of the two
following Hynix parts: H54G56CYRBX247 and H54G46CYRBX267. Failure to
set cs_pi_start_high_in_ect when using these parts will result in an
MRC cache failure and DUT will fail to boot.
BUG=b:292153199
TEST=`emerge-brya coreboot chromeos-bootimage`, flash and boot brya
variant to kernel.
Change-Id: I36040139b959c85c3ac220a34574caa12ca6c5fe
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
With currently set default PSP_SOFTFUSE_BITS for phoenix SoC,
the non-serial build does not boot on Myst.
Override PSP_SOFTFUSE_BITS by disabling SPIConfig to also get
the non-serial build booting.
The documentation of PSP_SOFTFUSE_BITS is available in #55758 doc (NDA).
BUG=b:292489356
TEST=Flash image-myst.bin, verify that it's able to boot on Myst
proto0.
Change-Id: Id4472fd85fdefcafb8378199dbaa054fab8b3274
Signed-off-by: Konrad Adamczyk <konrada@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76713
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Necessary to allow coolstar's Windows touchpad driver for this board,
since the touchpad is attached to the SMBus. The VID/DID combo used is
not registered/doesn't conflict with any currently in use, and would
be difficult to change at this point since the Windows drivers have
already been signed.
TEST=build/boot Win11, Linux on butterfly/lumpy/parrot, verify
touchpad driver works properly.
Change-Id: Ica3756e117fc58166958f37e7b007abb79d9d350
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76744
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Necessary to allow coolstar's Windows touchpad driver for this board,
since the touchpad is attached to the SMBus. The VID/DID combo used is
not registered/doesn't conflict with any currently in use, and would
be difficult to change at this point since the Windows drivers have
already been signed.
TEST=build/boot Win11, Linux on butterfly/lumpy/parrot, verify
touchpad driver works properly.
Change-Id: Ie1d882cac90211541a636d2dab297c343a12d66d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76743
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Necessary to allow coolstar's Windows touchpad driver for this board,
since the touchpad is attached to the SMBus. The VID/DID combo used is
not registered/doesn't conflict with any currently in use, and would
be difficult to change at this point since the Windows drivers have
already been signed.
TEST=build/boot Win11, Linux on butterfly/lumpy/parrot, verify
touchpad driver works properly.
Change-Id: I61912fd6db9eb4b8d202ab633b8c7ca5913e759f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
The patch disables PCH USB2 Phy power gating to prevent possible display
flicker issue for redrix board. Please refer Intel doc#723158 for
more information.
BUG=b:292435264
TEST=build and boot redrix
Change-Id: I34d10c763f4710d2c5678704320fd1cc8d8b6287
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76670
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Camera LED will blink several times as sensor is being probed during
kernel boot.
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that driver skips
initial probe during kernel boot and prevent privacy LED blink.
BUG=b:292173903
TEST=Build and boot on Yavilly EVT unit. Verify & observe Camera LED
blinking behavior.
Change-Id: Ic3e3439dc9313325189761b277e1a3bd1c1d9418
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76671
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On the mobile SoCs, SMN_IOHC_MISC_BASE_13B1 is the only IOHC misc base
address, but on for example Genoa it's the address of the IOHC misc base
of the second IOHC. Due to it not being the first one on Genoa, use 13B1
as part of the name instead of using an index of 0 which would look odd
in the Genoa case.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1db28ec03a3ba1c2040d8a1500ae17aa9705f6e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76756
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
The linux.mk makefile needs to be guarded, because it introduces a
dependency on the perl tooling.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: Ieb7aac672072858e0d6811628887f6a9eb9a8cb1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These boards do not actually support RTD3. The power GPIOs for
components are connected to 3.3V and the reset GPIO is connected to
`PLT_RST#`.
Change-Id: Id5e318c388f669d6b2935dc98ae29485955e6e72
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
After switching to S3, it was found that drives on the SATA port do not
exit D3cold on S3 exit. Disable RTD3 on the port until the issue can be
resolved.
Avoids the following error in Linux:
pcieport 0000:00:1d.0: Unable to change power state from D3cold to D0, device inaccessible
Tested on darp8 with a Samsung 970 EVO or Crucial P5 in J_SSD1.
Change-Id: Ib26f59db61acfbf9248cea379c197765d3d9c470
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76593
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since the per PCI root IOAPIC is now reported as domain MMIO resource
and the IVRS code now again probes for the IOAPIC resource on the domain
device, the IOAPIC resource doesn't need to be reported as resource of
the northbridge PCI device any more.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8604bd321ec4239076b1be99dca095e47f8b75a7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76600
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This reverts commit e33d253793 ("soc/amd/common/block/acpi/ivrs: fix
missing IOAPIC[1] error").
Now that the per PCI root domain IOAPIC MMIO resource is reported on the
domain device, we can again probe the resource on the domain device
instead of the northbridge PCI device in that domain. This will make the
IVRS code compatible again with the work in progress Genoa SoC support.
TEST=Linux doesn't complain about the IOAPIC[1] missing in the IVRS on
Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib861b19d798fc8ee6603e8803d8d1939be08d275
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76659
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Call read_non_pci_resources from amd_pci_domain_read_resources to tell
the resource allocator about the non-PCI MMIO regions within the data
fabric MMIO regions so that the allocator won't place any PCI MMIO in
the same areas.
TEST=On Mandolin 3 new non-PCI resources get reported to the allocator:
avoid_fixed_resources: DOMAIN: 0000 04 base fd100000 limit fd1fffff mem (fixed)
avoid_fixed_resources: DOMAIN: 0000 05 base fd000000 limit fd0fffff mem (fixed)
avoid_fixed_resources: DOMAIN: 0000 20000120 base fec01000 limit fec01fff mem (fixed)
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7f69b86e376e3368d4f156ccf93791cc00886489
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Add the SoC-specific non-PCI MMIO register list. PPR #57254 Rev 1.52 was
used as a reference.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I29b4ef947776ab8a6c215c1a5204769a9f61e6fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add the SoC-specific non-PCI MMIO register list. PPR #57019 Rev 3.05 was
used as a reference.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6f57df6ca09f1583409f6c4e68177b05b9f31def
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76597
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the SoC-specific non-PCI MMIO register list. PPR #57243 Rev 3.02 was
used as a reference.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2c5173e596f3f3f1c63165871178dbbd0e9641be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76596
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add the SoC-specific non-PCI MMIO register list. PPR #56569 Rev 3.04 was
used as a reference.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id99c64c172481984306814980a1ddf0b2d535413
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76555
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add the SoC-specific non-PCI MMIO register list. PPR #55570 Rev 3.18 was
used as a reference.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If7bfcdd9b70b71fe6aedcab3694698967d48e18e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76554
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Introduce the common read_non_pci_resources function to read the base
address of the non-PCI resources within the MMIO regions configured in
the data fabric registers and pass that info to the resource allocator.
Each SoC will need to provide implementations for get_iohc_misc_smn_base
and get_iohc_non_pci_mmio_regs in order for read_non_pci_resources to
know the SoC-specific base addresses, register offsets and MMIO region
sizes. In case of SoCs with only one PCI root domain, the domain
parameter of get_iohc_misc_smn_base will be unused, but in the case of
SoCs with more than one PCI root domains, this parameter will be used by
the SoC-specific code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If9aca67fa0f5a0d504371367aaae5908bcb17dd9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add bank locator and slot existance to the mainboard code.
TEST: Verified on Linux that all slots show in dmidecode -t 17.
Change-Id: I4ced36e26368d3f99a7341cb55a8deb118b2d1a4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Set AllowedSocketsInParallel to 1 for RMT builds.
This help in associating any failures encountered during RMT run
with the corresponding Socket/MC/DIMM.
Intel recommended setting EnforcePopulationPor to 1 for RMT runs
for debugging failures if any.
Change-Id: Ie2301368e9470cc23171c3c4eca9fe978e1513d4
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76679
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The SuperIO is not used so don't enable decoding of 0xE2 and
drop all code using it. It's not even required for the virtual
UART on 0x3f8 to work.
Add the virtual UART on 0x3f8 as ACPI device.
TEST: Verified on SBP1 that serial still works.
Change-Id: I8e431a0c8417435cc6e3ba16f97ff080e1656a7b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Add pujjo new supported memory parts in mem_parts_used.txt, generate
SPD id for this part.
1. Hynix H58G56BK7BX068
2. Samsung K3KL6L60GM-MGCT, K3KL8L80CM-MGCT
3. Micron MT62F1G32D2DS-026 WT:B
BUG=b:292452868
TEST=Use part_id_gen to generate related settings
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: Ia123a1cfd93a5e08ab0ba65f1d9be240d60ff356
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76672
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch creates a new variant screebo4es.
The new variant will support only ESx samples. The existing rex
variant will support the QS samples.
BUG=b:292280656
TEST=Able to build google/screebo4es board and boot on target
hardware.
Change-Id: If77b4a773bee3633008d39c1886b61869c9618de
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
The u-root.mk makefile needs to be guarded, because it introduces a
dependency on the go tooling.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: Ia89e4e7b9a1f73a7b622eeaa8d6148d99f9b327a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marvin Drees <marvin.drees@9elements.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Do not add type 0x63 entry to amdfw.rom when APOB_NV cache is disabled.
BUG=b:290763369
TEST=boot birman multiple times with/without APOB_NV cache enabled
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Iefe6f56d7dbedd289680f25a5f372eaa12e967b6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76568
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Disable the APOB cache for only Myst, and re-enable APOB for other
Phoenix SOC mainboards.
BUG=b:290763369
TEST=verify APOB cache is disabled
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Ie611e0b84611b2f50c989c75612fc2186b2dbfdf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76567
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add Kconfig option to disable the non-volatile APOB cache for a
mainboard using an SOC that supports APOB.
BUG=b:290763369
TEST=verify APOB cache is disabled when selected
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I0170355bbf29ea6386fa69a318e61f057b9a9a3f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76566
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Mapping to the fw_config of AUDIO_AMP in dedede,
and set new AUDIO_AMP configuration of ALC5650 as value 4.
BUG=b:284060672
BRANCH=dedede
TEST=build pass
Change-Id: Ic3dccd09d3ba1619cce2ac0d5f123badbeeaccdc
Signed-off-by: Daniel_Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
From ccache(1):
mtime
Hash the compiler’s mtime and size, which is fast. This is the default.
Hashing the compiler binary's content would only be necessary when we
expect different binaries of the same size with the same path (e.g.
during a compiler bootstrap) and wrong modification timestamps (might
happen when checking an older version out of a (package) repository).
Neither should be the case during our builds. And even if everything
fails at once, chances are additionally low that a wrong cache hit
would cause a problem.
tl;dr we're building and testing firmware, not toolchains.
Change-Id: I264a72c628559384fcc2060d777c52af927d5e14
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
The libncurses5-dev package no longer seems to be available in debian
sid. It's been marked as a transitional package, pointing to
libncurses-dev (ncurses 6) for since 2018, so this patch updates the
package to the new name.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I81e1a174ab25f573a7d7711eeeb26ef22fd3854b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
There were some issues with the current Linuxboot Makefiles.
- multithreaded compilation didn't work, because some prerequisites
were missing
- initramfs wasn't added for x86 qemu boot.
- riscv support was incomplete
It began with separate patches, but resulted in a clean up patch, that
is hard to separate. The most important changes are the following:
- Instead of phony targets, actual files are now used as prerequisites
- riscv can now be used as target
- initramfs works now also for x86
- instead of querying the most recent version from the internet, I set a
known working version (because I tested it) that can be customized
and/or upgraded in the future. The reasons:
- querying the version from the internet requires a constant
connection to the internet even after linux kernel is already
build (aka subsequent builds).
- one usually wants to use a known working version, but optionally
still have the posibillity to choose a custom one. This patch
introduces this possibility in its most simple form.
- I removed as much ifeq statements as possible and moved that
responsibility to Kconfig, because they tend to make the
Makefile less readable.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I25e757108e0dd473969fe5a192ad0733f1fe6286
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76150
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch increases the `tcc_offset` to reduce the TCC
(Thermal Control Circuit) activation temperature to avoid running
into abrupt power off during power cycle tests.
On Intel processors, the core frequency can be by an HW agent when
the current temperature reaches the TCC activation temperature.
The default TCC activation temperature is specified by MSR_IA32_TEMPERATURE_TARGET (which is 90°C for google/rex variants).
However, this patch adjusted the TCC by specifying an offset in
degrees C (i.e., using `tcc_offset` from variant override device tree).
Note: The bigger the TCC offset is, the lower the effective TCC activation temperature would be, to ensure that processors can be throttled earlier before the system critical overheats.
BUG=b:283008762
TEST=Able to perform power cycle on google/screebo w/o any crash/shutdown.
Change-Id: Ib19703877dbbfc26b2d9f538dda4f10c27cf872d
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76658
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Hook the PchHdaSdiEnable UPD so that mainboard can change the
settings via devicetree. PchHdaSdiEnable UPD enable HDA SDI lanes.
BUG=b:268546941
TEST=Verified the settings on google/brya using debug FSP logs.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I82bbfa5442936aefa53f8826e395b7ce75c895a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Adding EC_HOST_EVENT_PANIC to SCI mask allows the EC to interrupt the
Kernel when an EC panic occurs. If system safe mode is also enabled
on the EC, the kernel will have a short period to extract and save info
about the EC panic.
BUG=b:290985698
BRANCH=firmware-volteer-13672.B
TEST=Observe kernel ec panic handler run when ec panics
Change-Id: I87173f93d0e47baa816d15dad0777007342b4fdb
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Choose BOARD_GOOGLE_MODEL_REX while setting up the default config value
for variants created using google/rex model.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I107f4e375b5c9e9c0fb80c4d396164c10c1fc1e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76657
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
This patch creates a new variant rex4es. The new variant will support ESx samples. The existing rex variant will support the QS samples.
BUG=b:290732344
TEST=Able to build google/rex4es board and boot on target hardware.
Change-Id: I25dd1f42ee812f47289da0c2ef7aa79d6f340d48
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76605
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
This patch creates a rex model so that other variants developed using
`rex` baseboard are easy to land without duplicating the config
selection.
So far, `rex0` and `rex_ec_ish` are developed using the `rex` model.
The plan is to extend the support for `rex4es` and `rex4es_ec_ish`
variants.
TEST=Able to build and boot google/rex.
Change-Id: Id4e8d1162da93b7266ee1108f870e89b6d884ab9
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76608
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
acpi.c contains architectural specific things like IOAPIC, legacy IRQ,
DMAR, HPET, ... all which require the presence of architectural headers.
Instead of littering the code with #if ENV_X86 move the functions to
different compilation units.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I5083b26c0d4cc6764b4e3cb0ff586797cae7e3af
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
With arm64 -Wstack-usage= is enabled which is triggered on any use of
alloca(). Since this function basically works on x86 without wrecking
things and causing massive stack consumption it's unlikely to cause
problems on arm64.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I5d445d151db5e6cc7b6e13bf74ce81007d819f1d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76007
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
SoC family is able to provide SoC-specific information
via amd/fsp/<soc_family>/soc_dmi_info.h.
Use common amd/fsp/common/dmi_info.h for all AMD platforms.
This way, duplicated dmi_info.h files in
vendorcode/amd/fsp/<soc_family>/ can be removed.
BUG=b:288520486
TEST=Dump `dmidecode -t 17`.
Change-Id: I5e0109af51b78360f7038b20a2975aceb721a7d5
Signed-off-by: Konrad Adamczyk <konrada@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76107
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Jon Murphy