Use CPUID to get MAXPHYADDR and set MTRR masks correctly.
Also only BSP CPU clears MTRRs and initializes its Local APIC.
Change-Id: I89ee765a17ec7c041284ed402f21d9a969d699bd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/686
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This improvement of CAR code starts the sibling CPU processors and
clears their cache disable bits (CR0.CD) in case a hyper-threading
CPU is detected.
Change-Id: Ieabb86a7c47afb3e178cc75bb89dee3efe0c3d18
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/604
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Most or many Xeons have no MSR 0x11e.
I have previously tested that a HT-enabled P4 (model f25) can
execute this but will not have cache-as-ram enabled. Should work
for non-HT P4.
Change-Id: I28cbfa68858df45a69aa0d5b050cd829d070ad66
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/644
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
For a hyper-threading processor, enabling cache requires that both the
BSP and AP CPU clear CR0.CD (Cache Disable) bit. For a Cache-As-Ram
implementation, partial multi-processor initialisation precedes
raminit and AP CPUs' 16bit entry must be run from ROM.
The AP CPU can only start execute real-mode code at a 4kB aligned
address below 1MB. The protected mode entry code for AP is identical
with the BSP code, which is already located at the top of bootblock.
This patch takes the simplest approach and aligns the bootblock
16 bit entry at highest possible 4kB boundary below 1MB.
The symbol ap_sipi_vector is tested to match CONFIG_AP_SIPI_VECTOR
used by the CAR code in romstage. Adress is not expected to ever
change, but if it does, link will fail.
Change-Id: I82e4edbf208c9ba863f51a64e50cd92871c528ef
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/454
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Delete dead CAR code and whitespace fixes.
Replace cryptic 32bit hex values with existing LAPIC definitions.
Do not assume state of direction flag before "rep" instruction.
Do not load immediate values on temporary registers when not needed.
Parameter pushed on stack was not popped (or flushed) after returning
from call. This is a sort-of memory leak if multiple call's are
implemented the same way.
Change-Id: Ibb93e889b3a0af87b89345c462e331881e78686a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/643
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Cache was enabled for the last 4 MB below 4 GB when ramstage is
loaded. This does not cover the case of a 8 MB Flash and could
overlap with some system device placed at high memory.
Use the actual device size for the cache region. Mainboard
may override this with Kconfig CACHE_ROM_SIZE if necessary.
Change-Id: I622223b1e2af0b3c1831f3570b74eacfde7189dc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/641
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Copy model_6ex CAR as car/cache_as_ram_ht.inc to be extended
with hyper-threading CPU support.
Change-Id: I09619363e714b1ebf813932b0b22123c1d89010e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/606
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
After change it is more clear how romstage is linked twice and with
what scripts. Also with the change, it is easier to add some
object of static size that need to be re-compiled for the 2nd link.
One such object could be md5sum of executable.
Change-Id: Ib34d1876071a51345c5c7319a0ed937868817fd1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/803
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
There were cases where output file was generated and modified within
a recipe. If make was interrupted, it could exit with an output file
that appears as up-to-date, but was generated with incomplete recipe.
The output file should be created only when successful, in an atomic
operation. There could be other places in the make system which
require a similar fix, this needs to be investigated further.
Change-Id: I25c8ee23577a460eace196fd28c23cc67aa72a9a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/830
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
- Fix some poor programming practice (breaks of strict aliasing as well
as not checking the return value of read)
- Use PRIx64 instead of %llx to prevent compilation warnings with both
32bit and 64bit compilers
- Use same compiler command options when linking inteltool and when
detecting libpci for inteltool
Change-Id: I08b2e8d1bbc908f6b1f26d25cb3a4b03d818e124
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/752
Tested-by: build bot (Jenkins)
Reviewed-by: Mathias Krause <minipli@googlemail.com>
It's not significantly faster, but easier to read and smaller.
Change-Id: Ibab0b478873912d67bf1f07743f628586353368a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/755
Reviewed-by: Mathias Krause <minipli@googlemail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It's still on by default.
Change-Id: I8b6539eaf2f8d6a4fa975deb14789a00f2090d34
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/756
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
instead of having to edit the source code of tpm.c
Change-Id: I519d9ada14dd383e668a2da4219e5373a24c7c3d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/757
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This affects the algorithm when determining when to
transform a range into a larger range with a hole.
It is needed when for when I switch on an 8MB TSEG
and cause the memory maps to go crazy.
Also add header defines for the SMRR.
Change-Id: I1a06ccc28ef139cc79f655a8b19fd3533aca0401
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/765
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
With >= 4GB memory installed we get a memory map split in the middle
due to remap that has boundaries that are inconveniently aligned for
MTRRs due to the various UMA regions.
0000MB-2780MB 2780MB RAM (writeback)
2780MB-2782MB 2MB TSEG (uncached/SMRR)
2782MB-2784MB 2MB GFX GTT (uncached)
2784MB-2816MB 32MB GFX UMA (uncached)
2816MB-4096MB 1280MB EMPTY (N/A)
4096MB-5368MB 1272MB RAM (writeback)
5368MB-5376MB 8MB ME UMA (uncached)
The default MTRR allocation method of trying to cover everything
with one MTRR and then carve out a single uncached region does
not work for the GPU aperture which needs write-combining type,
and it also has issues trying to cover the uneven boundaries
in the avaiable variable MTRRs.
My goal was to make a minimal set of changes and avoid modifying
behavior on existing systems with an algorithm that is not always
optimal for a typical memory layout. So the flag 'above4gb=2'
will change these allocation behaviors:
1) Detect the number of available variable MTRRs rather than
limiting to hardcoded value. We need every last MTRR.
2) Don't try to cover all RAM with one MTRR, instead let each
RAM region get covered independently.
3) Don't assume uma_memory_base is part of the last region
and increase the size of that region. In this case the UMA
region is carved out from the lower memory region and it is
already declared as part of the ram region.
4) If a memory region can't be covered with MTRRs >= 16MB then
instead make a larger region and trim it with uncached MTRRs.
Change-Id: I5a60a44ab6d3ae2f46ea6ffa9e3677aaad2485eb
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/761
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
I forgot to implement this the first time around.
It does not seem to cause noticeable problems but
in heavy suspend/resume testing I saw a suspicious
crash in the kernel when trying to bring one of the
CPUs back online.
Change-Id: I950ac260f251e2683693d9bd20a0dd5e041aa26e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/770
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Since we do not run option roms in normal mode nothing was
initializing the BDA/EBDA and yet Linux depends very much
on it having sane values here. For the most part the kernel
tries to work around this not being initialized, but every
once in awhile (1/300 boots or so) it would end up reading
something that looked sane from BDA but was not and then
it would panic.
In this change the EBDA is unconditionally setup before devices
are initialized. I'm not set on the location in dev_initialize()
but there does not seem to be another place to hook it in so
that it runs just once for ALL platforms regardless of whether
they use option roms or not. (possibly hardwaremain?)
The EBDA setup code has been moved into its own location in
arch/x86/lib/ebda.c so it can be compiled in even if the option
rom code is not.
The low memory size is still set to 1MB which is enough to make
linux happy without having to hook into each mainboard to get a
more appropriate value. The setup_ebda() function takes inputs
so it could be changed for a mainboard if needed.
OLD/BROKEN would read garbage. Examples from different boots:
ebda_addr=0x75e80 lowmem=0x1553400
ebda_addr=0x5e080 lowmem=0x3e51400
ebda_addr=0x7aa80 lowmem=0x2f8a800
NEW/FIXED now reads consistent values:
ebda_addr=0xf6000 lowmem=0x100000
Change-Id: I6cb79f0e3e43cc65f7e5fe98b6cad1a557ccd949
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/769
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
idftool was failing to add the ME blobs into the output image in case
the blob size does not exactly match the size allocated for it in the
flashrom structure.
It is difficult to set the field in the structure to exactly match the
size (for some reason Intel flash tool fails to insert the correct
size even when given the exact ME blob). On the other hand there is no
harm in using am ME blob smaller than the allocated size, this change
modifies the tool building the image to allow for smaller components.
Change-Id: I1b04f90051b91157391943c9bad0eb06dd297431
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/751
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Future CPUs will require TSEG use for SMM
Change-Id: I1432569ece4371d6e12c997e90d66c175fa54c5c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/766
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This avoids using EBX and instead uses EDI where possible,
and ESI when necessary to get the EBX value out.
This allows me to enable -fpic for SMM TSEG code.
Also add a new CPUID extended function to query with ECX set.
Change-Id: I10dbded3f3ad98a39ba7b53da59af6ca3145e2e5
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/764
Tested-by: build bot (Jenkins)
Reviewed-by: Mathias Krause <minipli@googlemail.com>
This change makes significant changes to cbmem.py to make it use the
coreboot tables to find the memory console and timestamp areas instead
of looking for the in memory table TOC structure. That appears to be
more robust and gets cbmem.py working again after some unrelated
changes that affected memory layout.
It also introduces some small infrastructure to make accessing C style
structures in physical memory easier and more transparent.
Change-Id: I51833055a50c2d76423520ba6e059bf8fc50adea
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/762
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It's not used on any board supported by coreboot but has been
detected at run time since ages. No new boards (since 2000?)
are using the CONF2 method, so it is unlikely we ever have to
turn this on for a board.
Change-Id: I17df94a8a77b9338fde10a6b114b44d393776e66
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/758
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds a number of timestamps in ramstage and romstage
so we can figure out where execution time goes.
Change-Id: Iea17c08774e623fc1ca3fa4505b70523ba4cbf01
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/749
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It looks like the cbfstool utility generates the output file even when
it fails to generate it properly. This causes make, if started second
time in a row, after cbfstool failure, to continue beyond the point of
failure (as the corrupted output file is present in the output tree,
the second make invocation presumes that it is valid, as it is newer
than the dependencies).
The output file should be created only when successful, in an atomic
operation. There could be other places in the make system which
require a similar fix, this needs to be investigated further.
Change-Id: I7c17f033ee5937eb712b1a594122430cee5c9146
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/750
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
and initialize the TPM on S3 resume
This patch integrates the TPM driver and runs TPM resume upon an ACPI S3
resume without including any other parts of vboot.
We could link against vboot_fw.a but it is compiled with u-boot's CFLAGS
(that are incompatible with coreboot's) and it does a lot more than we
want it to do.
Change-Id: I000d4322ef313e931e23c56defaa17e3a4d7f8cf
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/731
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
... and hook it up in Kconfig. More code to come.
Change-Id: I24542d8ef97e2bce112c3aface681ceeb1a7c061
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/813
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The cbmem console structure and car global data are put in their own section,
with the cbmem console coming after the global data. These areas are linked
to be where CAR is available and at the very bottom of the stack.
There is one shortcoming of this change:
The section created by this change needs to be stripped out by the Makefile
since leaving it in confuses cbfstool when it installs the stage in the image.
I would like to make the tools link those symbols at the right location but
leave allocation of that space out of the ELF.
Change-Id: Iccfb99b128d59c5b7d6164796d21ba46d2a674e0
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/727
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Use an int in CAR global data to store whether or not the OXPCIE serial card
is actually there. Also, time out if the card doesn't show up quickly enough,
don't continue initialization if it's not there, and don't make the
initialization routine default to a card if none is found.
Change-Id: I9c72d3abc6ee2867b77ab2f2180e6f01f647af8c
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/728
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- cash -> Cache
- make the new size of the cbmem console buffer the default
Change-Id: Ia906077257e93622ad56bc54a42f8184ade78b29
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/726
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These are guarded by individual Kconfig entries. The deprecated
CONFIG_PCIE_TUNING defines have been removed in favor of using specific
config options.
This is the generic half, there is board-specific pieces
still to come that tune before and after ASPM is enabled.
Change-Id: I3fe46282eada67629e9eeeed07e487dff54f2729
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/735
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
We need to provide u-boot access to several different CBMEM
sections. To do that, a common coreboot table structure is used,
just different tags match different coreboot table sections.
Also, the code is added to export CBMEM console and MRC cache
addresses through the same mechanism.
Change-Id: I63adb67093b8b50ee61b0deb0b56ebb2c4856895
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/724
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This change exports the timestamp table pointer through coreboot
table to make it possible for u-boot to add timestamps to the
table.
Inclusion of cbmem.h allows to drop external declarations in
coreboot_table.c.
Change-Id: Ia070198cee7a6ffdaeece03d9d15bd91e033b6d1
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/716
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is a python script which is supposed to run on a target
which is controlled by coreboot. The script examines top of
memory looking for the CBMEM signature at addresses aligned at
128K boundary. Once the script finds the CBMEM, it iterates
through the CBMEM table of contents and parses two entries: the
timestamps and the console log.
This submission is just a template to build upon to create a
utility for displaying CBMEM information while running Linux on
the target.
BUG=chrome-os-partner:4200
TEST=manual
See test description of d81e6b8c8d41f2d6 for test procedure.
Change-Id: Id863a8598eaadc2d20d728f9186843e65cbe6f37
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://gerrit-int.chromium.org/5942
Tested-by: Vadim Bendebury <vbendeb@google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/723
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The appropriate Makefiles are modified to include the required
source code in compilation.
Change-Id: I91842b1ba0f89d611d3249b63c020a2713a9124f
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/722
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The new added code is compiled in when the CBMEM_CONSOLE config
flag is enabled.
Change-Id: Ifd1f492ce6321412a014333babbc5b3f14635988
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/721
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add CBMEM type for the console buffer section.
Change-Id: I02757c06d71e46af77b02b90b0e6018a37b62406
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/720
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The CBMEM console driver saves console output in a CBMEM area, which
then is made available to Linux applications for perusing.
There are some system limitations which need to be worked around
to achieve this goal:
- some console traffic is generated before DRAM is initialized,
leave alone CBMEM initialized.
- after the RAM based stage starts, a lot of traffic is generated
before CBMEM is initialized.
As a result, the console log lives in three different places -
the bottom of the cache as RAM space, the CBMEM buffer (where it
is expected to be) and a static buffer used early in the RAM
stage.
When execution starts (in the cache as RAM mode), the console
buffer is allocated at the bottom of the cache as RAM memory
address range. Once DRAM is initialized, the CBMEM structure is
initialized, and then the console buffer contents are copied from
the bottom of the cache as RAM space into the CBMEM area right
before the cache as RAM mode is disabled. The
src/lib/cbmem_console.c:cbmemc_reinit() takes care of the
copying.
At this point the cache as RAM memory is about to be disabled,
but the ROM stage is still going generating console output. To
make sure this output is not lost, cbmemc_reinit() saves the new
buffer address at a fixed location (0x600 was chosen for this),
and the actual "printing" function checks to see if the RAM is
already initialized (the stack is in RAM), and if so, gets the
console buffer pointer from this location instead of using the
cache as RAM address.
When the RAM stage starts, a static buffer is used to store the
console output, as the CBMEM buffer location is not known. Then,
when CBMEM is reinitialized, cbmemc_reinit() again takes care of
the copying.
In case the allocated buffers are not large enough, the excessive
data is dropped, and the copying routine adds some text to the
output buffer to indicate that there has been data lost and how
many characters were dropped.
Change-Id: I8c126e31db6cb2141f7f4f97c5047f39a8db44fc
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/719
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some experiments have demonstrated that total amount of text
generated by coreboot console when BIOS_SPEW level is enabled
exceeds 40KB.
Console output generated before DRAM is initialized can exceed
2KB. This patch introduces the new configuration option and
assigns adequate default values to cache based and DRAM based
console buffers.
BUG=chrome-os-partner:4200
TEST=manual
. run the following commands in the root directory
cp config.stumpy .config
make menuconfig
. enable the new option (Console->Send console output to a CBMEM buffer)
. save the configuration
Observe the following settings added to the config:
+CONFIG_CONSOLE_CBMEM=y
+CONFIG_CONSOLE_CBMEM_BUFFER_SIZE=0xae00
+CONFIG_CONSOLE_CAR_BUFFER_SIZE=0xc00
Change-Id: I209603f516244ae136631e6281ba21ebc6fb1710
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://gerrit-int.chromium.org/5855
Tested-by: Vadim Bendebury <vbendeb@google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/718
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This change adds 128K to the memory amount set aside for CBMEM in
case the CBMEM console is enabled (to keep the CBMEM 128K byte
aligned). The console buffer size is being set to 64K, which is
enough to accommodate the most verbose coreboot console and
u-boot console.
Change-Id: If583013dfb210de5028d69577675095c6fe2f3ab
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/725
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These get used later for saving/restoring the MRC scrambler
seed values on each boot.
Change-Id: I6e23f17649bea6d22c4b279ed8d0e5cb6c0885e7
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/717
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Kyösti Mälkki