The Embedded Controller (EC) for Pit is connected via SPI2, and needs to be
configured before we can talk to it.
Change-Id: I1f8e921b4616f15951f3e5fae1ecbf116de4ba90
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3707
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Some initialization / shutdown commands should be paired correctly in a SPI I/O
session. For example, setting CS should be enabled and disabled in each read;
and the bus width (byte or word) should be configured only when opening /
closing the SPI device.
Change-Id: Ie56b1c3a6df7d542f7ea8f1193ac435987f937ba
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3706
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I4feabc448945c4664d3114c0c8afdad48338230a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3705
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The functions which checked the status of a transfer would return success if
the bus was no longer occupied, even if it's no longer occupied because the
transfer failed. This change modifies those functions to return three possible
values, 0 if the transfer isn't done, -1 if there was a fault, and 1 if the
transaction completed successfully.
Change-Id: Idcc5fdf73cab3c3ece0e96f14113a216db289e05
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3704
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The exynos manual suggests hooking the mmc ip blocks to the mpll. They had
been set to use a different pll. This changes them over and modifies the
divider so that the frequency stays the same.
Change-Id: I85103388d6cc2c63d1ca004654fc08fcc8929962
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3703
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This allows us to set different speeds for each HSI2C bus.
Change-Id: I50cc257aad9ef50025d0837b0516940b956efc02
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3701
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change adjusts some clock settings so that they match U-Boot. There are
three different changes.
1. Change the source for psgen from the oscillator clock to the pclk.
2. Change the pll feeding the SPI busses from epll to mpll, as suggested in
the manual.
3. Change the SPI prescaller.
Change-Id: Ib54a255bc14fc286629dac86db9b8cf8e75a610b
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3700
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The clock divider was being read from registers incorrectly which meant that
the periph rate was wrong.
Change-Id: I50efb62849ef29bdfb0efc56c49642d3edca094c
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3699
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Wait for UART FIFO to be ready.
(Credit to dhendrix for finding the bits to test with.)
Change-Id: Ib6733e422cbc1c61b942bd90d85f88a3f412d6ff
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3698
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Chrome EC protocol V3 has several new command structure and constants defined.
Simply cherry-picking changes from upstream.
Change-Id: I7cb61d3b632ff32743e4fa312e0cc691c1c4c663
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3748
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
... this is needed for libpayload to talk to USB devices.
(forward ported from https://gerrit.chromium.org/gerrit/#/c/55554)
Change-Id: I5a20864689efd0c0149775e6d85b658e0cc6715c
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3697
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
... this is needed for libpayload to talk to USB devices.
Change-Id: I7eb19003c9e96efb5fa7a3f97c7b15f3ef332687
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3696
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I5cddffc2e524aae7a31a8f94f67e03a5b7e15c82
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3695
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Otherwise we have to worry about hand off between bootblock and
romstage. Too much complexity
Change-Id: I89bf8a229dba7e1330accadf9a732d831ebc4827
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3694
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is already called in ARMv7 bootblock_simple.c so we don't
want to do it twice
Change-Id: I80cb41035b8a77787e04f2ea58a1cd372cea97d8
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3692
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I6b28bb95c7decbe3eed33b5b5a029bee48bbe403
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3691
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Currently, the exception handling code on ARM turns on alignment checks as an
easy way to generate an exception for testing purposes. It was leaving it on
which disabled unaligned accesses for other, unlreated code running later.
This change adjusts the code so the original value of the alignment bit is
restored after the test exception.
Change-Id: Id8d035a05175f9fb13de547ab4aa5496d681d30c
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3690
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The GPIOs used by vboot and setting up the display and backlight were still
the ones for snow. This change updates them so they're correct for pit.
Change-Id: I06ba773da3af249efec723bb90c2e9e8075a777a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3689
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The MAX_CPUS option is only used on x86 currently, so there's no reason to
have it in the pit config.
Change-Id: I270bbfd3aff781d88304791b1d9735777643caab
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3688
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
That part isn't used on pit.
Change-Id: I48f3a10f7e6eb89b1e9630d2372b6865b4c12a7f
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3687
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
On pit, the tps65090 is connected to the EC and has to be accessed by proxy.
Until we have that implemented, this change removes calls to tps69050 which
will never succeed, and stops compiling in the driver.
Change-Id: I7218f85f9f26623bd13aaaf8ded0638b3b2f874a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3686
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The members data structures in dmc.h are intended to have a particular size.
Rather than assume that particular types are the right size, we should use
types that are guaranteed to be the right size. Also, since the registers are
at particular offsets as well, the structures should be packed.
Change-Id: I9cc11d7451f92ba3eb85c6be88ecbc62c7a5652d
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3685
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The previous driver was a bit awkward and not entirely correct. This change
primarily replaces the read/write functions with simpler and more robust
(hopefully) version.
Change-Id: I55f0ad8faec2de520e27577bd6dad9c0118d8171
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3684
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
For all other CPUs, we unconditionally include the CPU Kconfig
files in the CPU directory, not in the vendor directory. Do the
same thing for the Exynos CPUs. This allows us to make CPU dependent
changes in the directory of that CPU alone.
Also, drop some unused Kconfig variables from the Exynos Kconfig
files.
Change-Id: I4e4c22a0693988834e619dd33d121bf994ed57e8
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3683
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The dmb should be executed before reading operations, and before/after writing
operations.
Change-Id: I572136a2f9a07eb2c38a112f5deeb2de0c0fd46c
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3682
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This updates the low-level I2C code to handle the new high-speed
HSI2C/USI inteface. It also outputs a bit more error information
when things go wrong. Also adds some more error prints. Timeouts
really need to be noted.
In hsi2c_wait_for_irq, order the delay so that we do an initial
sleep first to avoid an early-test that was kicking us out of the
test too soon. We got to the test before the hardware was ready
for us. Finally, test clearing the interrupt status register every time
we wait for it on the write. Works.
Change-Id: I69500eedad58ae0c6405164fbeee89b6a4c6ec6c
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3681
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This updates the setup_power() function to actually set up the PMIC
which is on this board (the MAX77802).
Change-Id: I9c6f21f183dacc0bca71277e681e670834412d78
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3680
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds register offsets and important values for the Maxim
MAX77802 PMIC.
Change-Id: I3724b82bcb235b6684d2b976876f628f1ffbed3f
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3747
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We saw a problem on x86 last year in which setting direction, then value,
glitched the output and caused problems. Change this code to set the output,
then the direction.
Change-Id: I3e1e17ffe82ae270eea539530368a58c6cfe0ebe
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3679
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The 5420 clock code still had a data structure in it for the 5250 clock
registers which was used by some of the clock functions. That caused some
clocks to be configured incorrectly, specifically the i2c clock which was
running at about 80KHz instead of about 600KHz as configured by U-Boot.
Also, the registers and bit positions used to set up the SPI bus were not
consistent with U-Boot, and if the bus clock rate were set to 50MHz, a rate
which has historically worked on snow, loading would fail. With these fixes
the clock rate can be set to 50MHz and the device boots as much as is
expected. I haven't yet measured the actual frequency of the bus to verify
that it's now being calculated correctly.
Change-Id: Id53448fcb6d186bddb3f889c84ba267135dfbc00
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3678
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested and working. Gets us to ramstage.
Change-Id: Ib9ea4a6c912e8152246aaf4f1f084a4aa1626053
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3677
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds entries for I2C8-10 to giant switch statement in
clock_get_periph_rate(). It also eliminates the I2C peripheral's
usage of clk_bit_info since it's confusing and error-prone.
Change-Id: I30dfc4c9a03fbf16d08e44e074189fb9021edb6d
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3676
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The code has been there for quite a while but was never enabled.
Change-Id: I4ec3dcbb3c03805ac5c75872614e5d394df667cf
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3675
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The pinmux code for the exynos5250 was all bundled into a single, large
function which contained a switch statement that would set up the pins for
different peripherals within the SOC. There was also a "flags" parameter, the
meaning of which, if any, depended on which peripheral was being set up.
There are several problems with that approach. First, the code is inefficient
in both time and space. The caller knows which peripheral it wants to set up,
but that information is encoded in a constant which has to be unpacked within
the function before any action can be taken. If there were a function per
peripheral, that information would be implicit. Also, the compiler and linker
are forced to include the entire function with all its cases even if most of
them are never called. If each peripheral was a function, the unused ones
could be garbage collected.
Second, it would be possible to try to set up a peripheral which that function
doesn't know about, so there has to be additional error checking/handling. If
each peripheral had a function, the fact that there was a function to call at
all would imply that the call would be understood.
Third, the flags parameter is fairly opaque, usually doesn't do anything, and
sometimes has to have multiple values embedded in it. By having separate
functions, you can have only the parameters you actually want, give them
names that make sense, and pass in values directly.
Fourth, having one giant function pretends to be a generic, portable API, but
in reality, the only way it's useful is to call it with constants which are
specific to a particular implementation of that API. It's highly unlikely that
a bit of code will need to set up a peripheral but have no idea what that
peripheral actually is.
Call sights for the prior pinmux API have been updated. Also, pinmux
initialization within the i2c driver was moved to be in the board setup code
where it really probably belongs. The function block that implements the I2C
controller may be shared between multiple SOCs (and in fact is), and those
SOCs may have different pinmuxes (which they do).
Other places this same sort of change can be made are the pinmux code for the
5420, and the clock configuration code for both the 5250 and the 5420.
Change-Id: Ie9133a895e0dd861cb06a6d5f995b8770b6dc8cf
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3673
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The memset and memcpy functions are assembled as ARM code, likely because
that's the default of the assembler. Without special annotation, the assembler
and linker don't know that those symbols are functions which need special
handling so that ARM/thumb issues are handled properly. This change adds that
annotation which gets those functions working in Coreboot which is compiled as
thumb. Libpayload and depthcharge are compiled as ARM so they don't *need* the
annotation since it just works out in ARM mode, but it's the safe thing to do
in case we change that in the future.
We should explicitly select ARM vs. thumb when assembling assembly files to be
consistent across builds and toolchains.
Change-Id: I814b137064cf46ae9e2744ff6c223b695dc1ef01
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3672
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It might be that you want an early console in romstage before RAM is up, but
you can't or don't want to support the console all the way back in the
bootblock. By making the console in those two different environments
configurable seperately that becomes possible.
On the 5250 console output as early as the bootblock works, but on the 5420 it
only starts working in the ROM stage after clocks have been initialized.
Change-Id: I68ae3fcb4d828fa8a328a30001c23c81a4423bb8
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3671
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are hundreds of GPIOs on the Exynos5420. Don't
always print all of them per default.
Change-Id: I2152ab760e31a335dbcd9d6ad32cd1eaae4b89bc
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3670
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
remove some unused code
Change-Id: I41602fb391c1910c588a4f9dcc7c2edefe8ab5bc
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3669
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If we clear the framebuffer and then flush it back to memory using cache
operations, the writes are going to be full cachelines at a time. If we
make it uncacheable first, the writes will be serialized writes of
whatever sized chunks memset uses, probably 4 bytes or less.
Change-Id: I960f87a370e97f9e91236ad796d931573bb3dbb8
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3668
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
At one time it seemed to be necessary to disable and then re-enable the
MMU when setting the framebuffer to be uncache-able due to bugs in the
MMU management code. Since those bugs have been fixed, this is no longer
necessary.
Change-Id: I7ce825cf5eaaa95119364d780cba0935752e4632
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: http://review.coreboot.org/3667
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The code that allocated space for the framebuffer was adding space for a
vestigial color map which was never used. It was also passing around a
structure which was used to calculate a single value which was already
known when that structure was put together. Eliminate the extra space,
and pass the single value instead of the structure.
Change-Id: I29bc17488539dbe695908e47f0b80c07e102e17d
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: http://review.coreboot.org/3666
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The code which figured out the rate of the input clock to a peripheral was
doing several things wrong. First, it was using the wrong values when
determing what the source of a clock was set to. Second, it was using the
wrong offset into that register to find the current source setting.
This change fixes the constants which select a clock source which get some
more things working, but doesn't attempt to fix the bit position table.
Change-Id: Id7482ee1c78cec274353bae3ce2dccb84705c66a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3665
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Not all ARM systems need "BL1", and the layout of BL* and bootblock may be
different (ex, Exynos 5250 may use a new BL1 with variable length checksum
header).
To support that better, define the real base address (and ROM offset) of boot
block, and then we can post-processing ROM image file by filling data / checksum
and any other information.
Change-Id: I0e3105e52500b6b457371ad33a9aa546acf28928
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3664
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
On x86 there is a 16-byte alignment requirement for the
addresses containing the CPU microcode. The cbfs files
containing the microcode are used in memory-mapped fashion
when loading new mircocode. Therefore, the data payload's
address/offset of a cbfs file in flash dictates the resulting
alignment. Fix this by processing the CPU microcode cbfs
file separately as it uses $(CBFSTOOL) to find the proper
location within the provided rom image.
Change-Id: Ia200d62dbcf7ff1fa59598654718a0b7e178ca4c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3663
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The LPC-based ChromeOS EC uses several ioport regions to communicate with
the AP. In order for the new unified userspace access method to work, we
need them to be reserved by the BIOS.
Before /proc/ioports shows:
0800-0803
0804-08ff
We'd like just a single 256-byte region at 0x800, but ASL can't handle that.
So this will work:
0800-087f
0880-08ff
Change-Id: I3f8060bff32d3a49f1488b26830ae26b83dab79d
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: http://review.coreboot.org/3746
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are hundreds of GPIOs on the Exynos5250. Don't
always print all of them per default.
Change-Id: Ie349f2a4117883302b743027ed13cc9705b804f8
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3661
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Hung-Te Lin