When the board is in S3 and S5 the WLAN_DISABLE_L signal
can leak power into the WLAN power well since the GPIO
controlling WLAN_DISABLE_L is in the suspend well. Therefore,
drive WLAN_DISABLE_L low to avoid the power leak.
Change-Id: I1a0df80dd47fdbd535aca7a9d49253794c480606
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61421
Reviewed-on: http://review.coreboot.org/4358
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
USB2 Port A set to 6.4" and Back Panel
USB2 Port B set to 5.2" and Back Panel
USB2 Port C set to 12.3" and Internal
Other devices all set to Internal.
build and boot on falco and check settings.
Based on the config settings all ports end up with
tuning param 1 == 5 and param 2 == 2
U2ECR[0] = 0x00059501
U2ECR[1] = 0x00059501
U2ECR[2] = 0x00059501
U2ECR[3] = 0x00059501
U2ECR[4] = 0x00059501
U2ECR[5] = 0x00059501
U2ECR[6] = 0x00059501
U2ECR[7] = 0x00059e01
Change-Id: I6b9e6df2679036a501355e6b389a486a6f178f99
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61297
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4350
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This CPU does not support Configurable TDP and so far does
not need to use Controllable TDP.
Change-Id: I15599cd4e6890dd5c9d9f99bc4e95307a8dcc827
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60657
Reviewed-on: http://review.coreboot.org/4347
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On some systems there may be 2GB SKU that is the same as the
4GB SKU but just one channel of memory. In that case we need
to ensure that both copies of the same SPD source end up
populated by ensuring that repeated entries are included by
using $+ instead of $^.
Alternatively we could do the check inside romstage, but it
is already set to behave this way if the SPD gets populated
correctly.
I changed spd_index to 3 in falco romstage to force it to
pretend it was a 2GB config of the same memory, then booted
to ensure it was indeed limited to 2GB.
memcfg channel[0] config (00780008):
ECC inactive
enhanced interleave mode on
rank interleave on
DIMMA 2048 MB width x16 single rank, selected
DIMMB 0 MB width x16 single rank
memcfg channel[1] config (00600000):
ECC inactive
enhanced interleave mode on
rank interleave on
DIMMA 0 MB width x8 single rank, selected
DIMMB 0 MB width x8 single rank
Change-Id: Ibfe5051ccda2fe69e8caff3f3c264116e3411c65
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59483
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Jay Kim <yongjaek@chromium.org>
Reviewed-on: http://review.coreboot.org/4319
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The OIPG package needs to have >1 member to make the chromeos_acpi
kernel driver do the right automagic sysfs topology creation.
Additionally an "unimplemented" GPIO should be reported as 0xFF
because 0 is a valid GPIO number.
verify crossystem on slippy
$ sudo crossystem | grep -e recoverysw_cur -e wpsw_cur
recoverysw_cur = (error)
wpsw_cur = 1
Change-Id: I06dff09152bde30a3ffe58b1defe9d299155472c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57471
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4221
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This config option was not enabled which was preventing
the user from enabling developer mode from recovery mode.
With this enabled we can disable the "dev mode by default"
behavior and let people enable it by entering recovery mode.
This will make the firmware behave like a typical chromeos
device.
Peppy is left in "default dev mode" until after bringup.
1) boot slippy in normal mode by default
2) enter recovery mode with servo button
3) Ctrl+D on USB keyboard to enter developer mode
4) boot slippy in developer mode
Change-Id: I414c0d10dd0489e3c89798f75a2872a43297c8d8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57350
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4220
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Those building Chromebook firmware from coreboot git might be more
interested in building without ChromeOS extras.
Change-Id: I2f176d059fd45bf4eb02cc0f3f1dcc353095d0ce
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3977
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
- Add a new USB location field
- Add a new "ddr_refresh_2x" field, enabled on Falco only
- Fix copy+paste bug in baskingridge
Checked that tREFI is halved during memory setup in the memory
training log:
tREFImin = 6240 << DEFAULT
C(0).tREFI = 0xc30 << MODIFIED (=3120)
C(0).tREFI = 0xc30 << MODIFIED (=3120)
Also ensure that the SD card is detected properly again.
Change-Id: Ie3a82c08df06ada9af56282b5255caefa56487f2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57349
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4219
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
These are based on the datasheet and I included the timing
values I used from the docs.
Change-Id: Ib75b2c5e50ac09d1e4cf9dd22229bb0f0a8965a4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58540
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4234
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Set nid 0x12 instead of nid 0x05. The DMIC is on NIC 0x12.
Change-Id: Ifc883b65a50aeec6a6d3ad02fe8418f124e6241d
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58711
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Jay Kim <yongjaek@chromium.org>
Tested-by: Jay Kim <yongjaek@chromium.org>
Reviewed-on: http://review.coreboot.org/4246
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
SPD GPIOs were being read prior to initialization in romstage_common. To
fix, pass the copy_spd function to romstage_common, to be called at the
appropriate time (after PCH init, before DRAM init).
Change-Id: I2554813e56a58c8c81456f1a53cc8ce9c2030a73
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58608
Reviewed-on: http://review.coreboot.org/4237
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The wake device input pins are active low and the
GPIOs need to be set as inverted when they are marked
as an input so they are not spuriously logged.
suspend/resume on slippy with trackpad wake:
8 | 2013-05-29 07:43:14 | ACPI Enter | S3
9 | 2013-05-29 07:43:18 | ACPI Wake | S3
10 | 2013-05-29 07:43:18 | Wake Source | GPIO | 12
and with power button wake:
11 | 2013-05-29 07:43:35 | ACPI Enter | S3
12 | 2013-05-29 07:43:40 | EC Event | Power Button
13 | 2013-05-29 07:43:40 | ACPI Wake | S3
14 | 2013-05-29 07:43:40 | Wake Source | Power Button | 0
Change-Id: I15d38dcc9b2fb4b2b0eb27da358fa3c343e22323
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56940
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4209
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The EC was disabling flash commands and sysjump was not working
properly. With those two fixed software sync works properly.
Google Chrome EC MKBP driver ready, id 'slippy_no_version'
Clearing the recovery request.
EC hash:7fea29992ef72e3e64d8ffe522aa1dfa68dcb44a2da96a4c19530ea1a0bd22c4
EC-RW hash address, size are 0xffa1cfe8, 32.
Hash = 727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
Expected hash:727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
EC-RW firmware address, size are 0xffad000c, 57180.
VbEcSoftwareSync() - expected len = 57180
Computed hash of expected image:727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
VbEcSoftwareSync() updating EC-RW...
VbEcSoftwareSync() jumping to EC-RW
VbEcSoftwareSync() in RW; done
Change-Id: I63ca00d6c94854f2b395eb736ce20792da5f8de2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56821
Reviewed-on: http://review.coreboot.org/4208
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Set verbs to reflect the layout used for ALC283 in Falco,
which ends up being the same as Slippy.
Change-Id: I3dce4effefaa91ee5bdcbe2a8a3750ebc41376ad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58196
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4232
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
RAM_ID indices have been changed and settled on a 2GB config
that will be the same DRAM chips but only used in one channel.
Change-Id: I444e655883ae045622ab3dfb964da4d7f86e1c0d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56810
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4198
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are placeholder values until we can configure for
the exact panel.
Change-Id: If40367c0e5f80d46d085c89b0edae60f1ccacdaf
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56808
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4197
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add the onboard I2C devices for Falco trackpad/lightsensor
and generate SMBIOS Type41 tables for them.
Add ACPI device for the trackpad to expose the interrupt map
to the OS so it can be used.
Configure interrupt GPIOs as PIRQ type and wake GPIOs as
just standard input type. The wake GPIO is reconfigured as
ACPI SCI in the specific device _DSW method. This prevents
the wake GPIO from generating a flood of SCI at runtime.
LTE_WAKE_L_Q and WLAN_WAKE_L_Q are left as ACPI SCI as these
are not repurposed interrupt pins so they are not generated
at runtime.
SIM_DET and ALS_INT_L are set as input since we don't have an
interrupt handler for them.
Change-Id: Ibe9687b2f7f41ead18353c3f650219fe6e94ae2f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56632
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4191
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This was provided by the vendor but I added the part number at
byte 128-143 so it can be identified when extracted by mosys.
Change-Id: Ib1e430cd390b4dbc013fc0802f1a59c1a0412577
Reviewed-on: https://gerrit.chromium.org/gerrit/56634
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4192
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Update and use the new pei_data data structure. Now that the
reference code is fixed it's possible to properly disable/enable
the USB2 and USB3 ports correctly.
Change-Id: I075c646e7574be354420b6e59507e8917a97d0f0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56594
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4185
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Only the first two DIMM SPDs are specified so far
- GPIO map is updated
- iSSD power sequencing removed
- USB port map updated
Change-Id: I4172460d3b075bfd5bb22013a6225cf0e8f95b9c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56329
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4184
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
