The current SMM framework only allows the mainboard code to handle GPEs.
i.e., Events 0 - 23. This change allows the mainboard code to handle any
SMI events not handled by the SoC code. This will allow the mainboard
code to handle `SMITYPE_ESPI_SMI`.
BUG=b:222694093
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I81943e8cb31e998f29cc60b565d3ca0a8dfe9cb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Rename `BOARD_HP_SNB_IVB_LAPTOPS` to `BOARD_HP_SNB_IVB_LAPTOPS_COMMON`
to indicate and to make it clear that this option serves as base for
others.
Built HP EliteBook Revolve 810 G1 with BUILD_TIMELESS=1 and also with
`INCLUDE_CONFIG_FILE` disabled. coreboot.rom remains identical.
Change-Id: Icadeb8a33ae0787d2cd5da460065a2ed15256d64
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Based on the schematic carbine_adl-p_dvt_20211104.pdf, the GPP_D0 is
directly connected to FP module, Set GPP_D0 to GPO, DUT can flash FP
firmware successfully.
BUG=b:222188263, b:223906569
TEST=USE="project_gimble emerge-brya coreboot" and run the Fingerprint
Firmware Test.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I164ffff6bd3b4058d6e28247eb7c3ed46d3891b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62739
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
This patch introduces CONFIG_I2C_TRANSFER_TIMEOUT_US,
which controls how long to wait for an I2C devices to
produce/accept all the data bytes in a single transfer.
(The device can delay transfer by stretching the clock of
the ack bit.)
The default value of this new setting is 500ms. Existing
code had timeouts anywhere from tens of milliseconds to a
full second beween various drivers. Drivers can still have
their own shorter timeouts for setup/communication with the
I2C host controller (as opposed to transactions with I2C
devices on the bus.)
In general, the timeout is not meant to be reached except in
situations where there is already serious problem with the
boot, and serves to make sure that some useful diagnostic
output is produced on the console.
Change-Id: I6423122f32aad1dbcee0bfe240cdaa8cb512791f
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
All TGL mainboards are setting DIMM_SPD_SIZE to 512. Thus, default to
512 in the SoC Kconfig and drop it from the mainboard Kconfigs.
Change-Id: I9fd947b61c984e10bd5fba20b73280b08623a008
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62766
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add PCI ID's for APL/GLK so they can use HDA.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I37df388a93ffc06e716085a58d0d00ed5c6fa9e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
BUG=b:219616787
BRANCH=guybrush
TEST=emerge-guybrush coreboot
update the thermal setting value by measurement and
pass the thermal performance test
Change-Id: I3ba3ab990d5362c6f02d2ee5a023f4c5cca7fa45
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Using the GPP_F19 as privacy switch for camera in banshee.
BUG=b:223712143, b:216110896
TEST=emerge-brya coreboot chromeos-bootimage
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I67d65347ceac7152f1951018a633a2e93ee84e14
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
If the DRAM part number is not available in the SPD data (meaning filled
with 0x00) do not print it in the log.
Change-Id: If7224c6e114731b1c03915a2bde80f57369d0cee
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The pmic hwcid dumping should not be a warning, so we modify it to info.
BUG=none
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I4a930b69bd45d5f0d84c3d269ca721b287dbadea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
It's more reasonable to halt when we trigger watchdog reset because
the whole system should be reset afterwards.
BUG=b:222217317
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I726ba1599841f63b37062f9ce2e04840e4f250bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
C1-state auto demotion feature allows hardware to determine C1-state as
per platform policy. Since Brya sets performance policy to balanced from
hardware, auto demotion can be disabled without performance impact.
Also, disabling this feature results in 110 mW power savings during
video playback.
Note that C1state Autodemotion feature is not applicable for ADL-P SoC.
Hence recommendation is to keep it disabled.
BUG=b:221876248
BRANCH=firmware-brya-14505.B
TEST=Code compiles and correct value of c1-state auto demotion is passed
to FSP. Also power and performance impact has been measure by respective
teams.
Change-Id: I41eea916cdfe4a86e4d263e3191f5cb40fa33a90
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
FSP has a parameter to enable/disable c1-state autodemotion feature.
Boards/Baseboard can choose to use this feature as per requirement.
This patch hooks up this parameter to devicetree
BUG=b:221876248
BRANCH=firmware-brya-14505.B
TEST=Check code compiles and correct value has been passed to FSP.
Change-Id: I2d7839d8fecd7b5403f52f3926d1d0bc06728ed9
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
coreboot chip.h files mainly contains variable which allows board to
fill platform configuration through devicetree.
Since many of this configuration involves FSP UPDs, variable names were
in camel case which aligned with UPD naming convention.
By default coreboot follow snake case variable naming, so cleaning up
file to align all variable names as per coreboot convention.
During renaming process, this patch also removes unused variables
listed below:
-> SataEnable // Checked in SoC code based on PCI dev enabled status
-> ITbtConnectTopologyTimeoutInMs // SoC always passes 0, so not used
Note: Since separating out changes into smaller CL might break the
compilation for the patch set, this is being pushed as a single big CL.
BUG=None
BRANCH=firmware-brya-14505.B
TEST=All boards using ADL SoC compiles with the CL.
Change-Id: Ieda567a89ec9287e3d988d489f3b3769dffcf9e0
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Commit hash b8b40964 ( mb, soc: Add the SPD_CACHE_ENABLE) introduced
per mainboard logic to invalidate the mrc_cache.
This patch moves mrc_cache invalidating logic into IA common code and
cleans up the code to remove unused argument `dimms_changed` from SoC
and mainboard directory.
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=Able to build and boot redrix without any visible failure/errors.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6f18e18adc6572571871dd6da1698186e4e3d671
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
This patch adds `FSPM_UPD *` as argument for
mem_populate_channel_data() and read_spd_dimm().
This change will help to update the architectural FSP-M UPDs in
read_spd_dimm().
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=Able to build and boot redrix without any visible failure/errors.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I770cfd05194c33e11f98f95c5b93157b0ead70c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
This patch modifies `memcfg_init` and `variant_memory_init`functions
argument from FSP_M_CONFIG to FSPM_UPD.
This change in `memcfg_init()` argument will help to update the
architectural FSP-M UPDs from common code blocks rather than going
into SoC and/or mainboard implementation.
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=Able to build and boot redrix without any visible failure/errors.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3002dd5c2f3703de41f38512976296f63e54d0c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Hoglin and Herobrine (proto1) should share majority of GPIOs.
Conslidating the QUP initializations in mainboard. Also, putting
fingerprint init in a conditional as not all devices will have an FP
sensor.
BUG=b:182963902,b:223826899
BRANCH=None
TEST=booted BIOS on hoglin and check for i2c errors in dmesg
Change-Id: I48ce42760f2c75f04619b967a05909d2b3f28e2c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
SeaBIOS 1.16.0 was released on March 2nd. Thus, update the stable
version from 1.14.0 to 1.16.0.
Change-Id: I475a9be47171bfbe3b3c2d4d1d14bb753d8575a8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Currently the BayHub eMMC enable pin is using the default
configuration from the baseboard, which leads to RTD3 not being able
to control the GPIO when exiting and entering suspend. To fix this,
program the GPIO in the ramstage GPIO table.
BUG=b:222436260
TEST=USE="project_primus" emerge-brya coreboot chromeos-bootimage
scope enable pin while performing suspend stress and enable pin
works as expected.
test suspend stress 1000 cycles passed on primus.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I1b6f164cc326bd368addb1e143ad2cbd449bb08d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Pull GPP_D16 to low when suspending, otherwise it will remain active
and use power.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I2cbe7caf66e8d8c27414aca3b74416c2b8115ea1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
DDR4 SPD data needs to be 512 byte to comply with the spec.
Though there is no vital timing data used beyond 256 byte there are some
part information which will be used to show the part info in the
coreboot log. If the buffer is too small this log shows garbage.
This patch increases the SPD buffer size from 256 byte to 512 to avoid
side effects.
Change-Id: I5b88df7818cfd62b3579d69f9f5bb14880f49c8c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The patch uses generic enum type values for EOP command handler. So,
it renames cse_eop_result enum type to cse_cmd_result and also renames
the enum values to have generic name.
TEST=Build the code for Gimble
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ie0efa8fff08318ed863010db289959d113f4767e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The patch implements error handling as per the ME BWG guide. The BWG
recommends HECI interface reset if there is a timeout or malformed
response is received from the CSE. Also, the patch triggers HECI
interface reset if the CSE link state is not ready in the heci_send()
API.
TEST=Verify HECI Interface reset in the simulated error scenarios.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I3e4a97800cbc5d95b8fd259e6e34a32fc82d8563
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The patch implements below changes:
1. Implements different error codes and use them in appropriate
failure scenarios of below functions:
a. heci_send()
b. recv_one_message()
c. heci_receive()
2. As heci_send_receive() is updated to return appropriate error codes
in different error scenarios of sending and receiving the HECI
commands. As the function is updated to return 0 when success, and
non-zero values in the failure scenarios, so all caller function have
been updated.
BUG=b:220652101
TEST=Verified CSE RX and TX APIs return error codes appropriately in
the simulated error scenarios.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ibedee748ed6d81436c6b125f2eb2722be3f5f8f0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The verstage.c file contains PSP verstage specific code. We don't need
it when using x86 verstage.
BUG=b:193050286
TEST=Build and boot guybrush with x86 verstage
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6dc928cdce0c922bb18f4479b993c89dff106070
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62740
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This sets EPP value to be 45% for all Brya variants.
Historically, EPP Ratio has always been 50% (128) on Chrome platforms.
But on Intel Alderlake EPP ratio of 45% is recommended for optimal
power and performance on Chrome platforms.
BUG=b:219785001
BRANCH=firmware-brya-14505.B
TEST=
Use 'iotools rdmsr [cpu id] 0x774' command and check field 32:24 = 0x73.
Signed-off-by: Cliff Huang <cliff.huang@intel.corp-partner.google.com>
Change-Id: I973cfec72a0be24c56c4cd3283d2fe6e18400d02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This updates energy performance preference value to all logical CPUs
when the corresponding chip config is true.
BUG=b:219785001
BRANCH=firmware-brya-14505.B
Signed-off-by: Cliff Huang <cliff.huang@intel.corp-partner.google.com>
Change-Id: Ie59623fe715b0c545f8d4b6c22ab2ce670a29798
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Update PL1, PL2, and temperature sensor values from thermal team,
as well as, we remove unused temperature sensors according to
baseboard/devicetree.cb and mainboard schematic. After we check
DTT setting, the thermal and performance test pass.
BRANCH=dedede
BUG=b:204229229
TEST=on beadrix, run following commands:
localhost /tmp # cat /sys/class/thermal/thermal_zone*/type
x86_pkg_temp
INT3400 Thermal
TSR0
TSR1
TCPU
localhost /tmp # cat /sys/class/thermal/thermal_zone*/temp
45000
20000
32800
32800
39000
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Change-Id: Ibc59c4aa431f600158e744f5bbdc6d59a07a1ef3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62729
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Super Ni <super.ni@intel.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The one USB2 port on the XHCI2 controller should have the port ID 2.0,
since it's the first USB2 port on that XHCI controller.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4a370132960939bccec4eb69a6590d0880b04137
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62713
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GFX HDA is the audio controller that provides audio output via the
external display connection, ACP is the audio coporcessor for the on-
board audio codec and XHCI2 is the third XHCI controller that provides
one USB 2.0 port. All those devices are used, so enable them in the
board's devicetree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I186797a832470eb17752e06aa2fcc0b5c9db0398
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62571
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Select GL9750 driver and add power sequence according to datasheet:
GL9750S-OIY04 rev1.22.
BUG=b:223304292
TEST=check GL9750 can get enumerated by kernel 5.15.
01:00.0 SD Host controller: Genesys Logic, Inc Device 9750 (rev 01)
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ib6d461a56f6aeba30994daafe8993c36df4b309d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Enable pen garage. Pen detect is active low. And wake system when
eject.
BUG=b:223476974
TEST=evtest work as expected.
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "PRP0001:00"
Supported events:
Event type 0 (EV_SYN)
Event type 5 (EV_SW)
Event code 15 (SW_PEN_INSERTED) state 0
Properties:
Testing ... (interrupt to exit)
Event: type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Event: -------------- SYN_REPORT ------------
Event: type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I2f676301c3372a4760853ce9c10b75f94e22bbcd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
This change mostly changes links that were identified as broken by
the 'website_scans' jenkins job.
There were some links that seem to be up at times, but that are
identified by link-checker as broken because of SSL issues.
At least one other link was changed to point to archive.org so
that it doesn't break at some point in the future. We should
probably try to make sure that everything is archived there and
point to those versions when possible.
There are still lots more links to do.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I36868ddf6113e18fa6841427dd635c75445b7bef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
There is no need that the tutorial for flashing firmware has its own
point in the main menu. Thus, move it to the tutorial section.
Change-Id: Ife6d97254af4c006fe01480a78c76303f9cb34bb
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Thomas Heijligen <src@posteo.de>
In preperation for CB:62424, replace HTTP links pointing to the flashing
firmware tutorial with file paths to the Markdown files.
Change-Id: I6a271a912348cbe002bc9cced9922ed743e1133c
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Thomas Heijligen <src@posteo.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Only one ACPI device should be added to a PCIe root port. For the root
ports which already have device created, the generated code from this
driver needs to be merged with the existing device.
By default, this driver will create new device named DEV0.
This change allows to generate code under an existing device.
ex: (generate code under PXSX):
Scope (\_SB.PCI0.RP01.PXSX)
{
Name (_DSD, Package (0x02) // _DSD: Device-Specific Data
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301")
Package (0x01)
{
Package (0x02)
{
"UntrustedDevice",
One
}
}
})
}
BUG=b:221250331
BRANCH=firmware-brya-14505.B
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I80634bbfc2927f26f2a55a9c244eca517c437079
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Since the new loglevel markers were added, there will now be a marker
character at the beginning of the coreboot banner string, and this will
make the existing regular expressions meant to find it fail to match.
This patch fixes the problem by just allowing for a single extra
character there (any character to avoid the hassle of having to match
the marker explicitly). The extra character is optional so that we will
still continue to match banners from older versions of coreboot as well.
Since the `?` glyph is not available in basic POSIX regular expressions,
we have to switch to REG_EXTENDED syntax (should otherwise make no
difference). (Also, move side effects out of assert() while I'm here,
that's not actually safe for the standard libc implementation.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I99fb347eb1cf7b043a2113dfda7c798d6ee38975
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62720
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Get boot performance timestamps from CSE and inject them into CBMEM
timestamp table after normalizing to the zero-point value. Although
consumer CSE sku also supports this feature, it was validated on
CSE Lite sku only.
BUG=b:182575295
TEST=Able to see TS elapse prior to IA reset on Brya/Redrix
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 88,000
945:CSE started to handle ICC configuration 88,000 (0)
946:CSE sent 'Host BIOS Prep Done' to PMC 90,000 (2,000)
947:CSE received 'CPU Reset Done Ack sent' from PMC 282,000 (192,000)
0:1st timestamp 330,857 (48,857)
11:start of bootblock 341,811 (10,953)
12:end of bootblock 349,299 (7,487)
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Idcdbb69538ca2977cd97ce1ef9b211ff6510a3f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
GPIO 32 was not allocated correctly, updating to reflect the native
function use of the pin
BUG=b:214412172
TEST=Builds
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: Idadd2a802b3244eba8ee83f80d8f10baebe4ca40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62717
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Raul E Rangel