Change source file modes from 755 to 644
The following files have been grepped for changes:
*.c
*.h
*Kconfig*
*Makefile*
Change-Id: I275f42ac7c4df894380d0492bca65c16a057376c
Signed-off-by: Alec Ari <neotheuser@ymail.com>
Reviewed-on: http://review.coreboot.org/1023
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
MA785GM-US2H was left out of Kconfig. This
allows the option to select the board.
Change-Id: I9efea96c21dcd0754ab51824b410435b0b5300c2
Signed-off-by: Alec Ari <neotheuser@ymail.com>
Reviewed-on: http://review.coreboot.org/1022
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
We have a http accessible SeaBIOS mirror at review.coreboot.org.
Use it.
Change-Id: Icce8e4f9ca1fa69966c82423b2b27057f15b30d2
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1020
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The fadt.c is the same across all the platforms using the sb800
cimx southbridge wrapper.
Change-Id: Ifbbfc238732aa46aef96297eaa188b77d27151f3
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1019
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are the PMIO & PMIO2 read & write routines from
src/southbridge/amd/sb800/sb800.c & sb800.h for use in the cimx
tree. Currently most platforms using CIMX are calling WritePMIO()
directly from the src/vendorcode/amd/cimx/sbX00 directories
instead of using a wrapper function.
These functions only do byte reads & writes.
Change-Id: I881a6e2d4ddbba3dbdf4dd33e06313fe88b3682a
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/981
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
If serial uart (8250/16x50) takes abnormally long to respond, give
up on logging to serial console and instead let the system boot.
Also reference bit in LSR register with correct name.
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Ported from 9dd3ef165a to
uart8250mem.c:
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: Iaca4f57389c887110e6406d45053935891c96838
Reviewed-on: http://review.coreboot.org/826
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This is the beginning of a tool that transforms the i9x5 code to user
mode code. Consider this a very early stage although it does produce
two programs. Requires spatch 1.0 or greater.
To try it out, assuming you have an up-to-date spatch,
sh transform
make
make broken
Please don't fall to the temptation to auto-magicize this process.
It's primitive for a reason. That said, suggestions welcome of course.
Change-Id: I0188e36637b198b06c17f6d3c714d990e88bd57d
Signed-off-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/1003
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When bringing in nvramtool as build_opt_tbl replacement,
various platforms where left in the cold that don't
provide direct IO support from userland (or at least not
in a way we support).
Build nvramtool without CMOS support when done as part of
a coreboot build. We don't need to touch CMOS in this case.
Change-Id: Icc88d1d32f10384867a5d44b065f9aa119bb0d50
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/983
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Replace #elif (CONFIG_FOO==1) with #elif CONFIG_FOO
find src -type f -exec sed -i "s,\(#.*\)(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]1),\1\2,g" {} +
(manual tweak since it hit a false positive)
Replace #elif (CONFIG_FOO==0) with #elif !CONFIG_FOO
find src -type f -exec sed -i "s,\(#.*\)(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]0),\1\!\2,g" {} +
Change-Id: I8f4ebf609740dfc53e79d5f1e60f9446364bb07d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1006
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change is taken from Linux. It allows to check for Kconfig
definitions in the preprocessor and source code using the same
idiom.
Long term plan is to remove our Kconfig hack to #define values to 0,
and this helps.
This includes a tiny modification to the macros to fix romcc support.
Change-Id: I0fddbea8c8ca215cf226acf39cb329b0ba0445a5
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1005
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Prefix all CBFS output messages with CBFS:
- Add an option DEBUG_CBFS that is off by default. Without DEBUG_CBFS
enabled, the code will no longer print all the files it walks for
every file lookup.
- Add DEBUG() macro next to LOG() and ERROR() to specify which messages
should only be visible with DEBUG_CBFS printed.
- Actually print a message when the file we're looking for was found. :)
old:
Searching for fallback/coreboot_ram
Check cmos_layout.bin
Check pci8086,0106.rom
Check fallback/romstage
Check fallback/coreboot_ram
Change-Id: I2d731fae17a5f6ca51d435cfb7a58d6e017efa24
Stage: loading fallback/coreboot_ram @ 0x100000 (540672 bytes), entry @ 0x100000
Stage: done loading.
new:
CBFS: Looking for 'fallback/coreboot_ram'
CBFS: found.
CBFS: loading stage fallback/coreboot_ram @ 0x100000 (507904 bytes), entry @ 0x100000
CBFS: stage loaded.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/993
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Otherwise set_subsystem isn't called for these (as they're not
marked on_mainboard)
Change-Id: I08e781735c59e4aa61009d2afa165d782f5a849e
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/998
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The stable lint test "build-dir-handling" ran the build system
in a way that made it download the blobs repository. Since this
is part of the pre-commit hook, this might have kicked in with
users desiring not to have them.
Change-Id: I44a00137352c5966ff7fe2a030673276f6803908
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/999
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In a recent commit the SATA code of Panther Point / Cougar Point was
changed to enable AHCI mode depending on the device tree settings rather
than a hard code hidden in romstage.c. However, Emerald Lake 2 was not
fixed up accordingly.
Change-Id: I6c93f386509361e1ab5565b0e4d0e84f0ba282a2
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/995
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: I1ec7a7e54513671331ac12f08d5f59161b72b0fd
Example:
PSS: 1900MHz power 35000 control 0x1300 status 0x1300
PSS: 1600MHz power 28468 control 0x1000 status 0x1000
PSS: 1400MHz power 24291 control 0xe00 status 0xe00
PSS: 1200MHz power 20340 control 0xc00 status 0xc00
PSS: 1000MHz power 16569 control 0xa00 status 0xa00
PSS: 800MHz power 12937 control 0x800 status 0x800
PSS: 1900MHz power 35000 control 0x1300 status 0x1300
PSS: 1600MHz power 28468 control 0x1000 status 0x1000
PSS: 1400MHz power 24291 control 0xe00 status 0xe00
PSS: 1200MHz power 20340 control 0xc00 status 0xc00
PSS: 1000MHz power 16569 control 0xa00 status 0xa00
PSS: 800MHz power 12937 control 0x800 status 0x800
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/994
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The CBMEM_ID_RESUME_SCRATCH area is only used by Agesa code, on one
particular board (AMD Persimmon). Make the creation of that section
depending on Agesa so it does consume space on non-Agesa systems.
Change-Id: I2a1a4f76991ef936ea68cf75928b20b7ed132b84
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/992
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Sandybridge memory initialization produces some amount of training data
that has to be kept around in CBMEM. Add a descriptive name to the CBMEM
pretty printer to prevent it from just printing the hex value.
Change-Id: I587c0bc3dfcf389ba298d445d2594eef73bc69a8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/990
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Another bug in the Intel microcode update code that existed since we switched
to LinuxBIOSv2 in 2004:
The inline assembly code that reads the CPU revision from an MSR after running
cpuid(1) trashes registers EBX and ECX. Only ECX was mentioned in the clobber
list. C code running after this function could silently access completely wrong
data, which resulted in the wrong date being printed on microcode updates (and
potentially other issues happening until the C code writes to EBX again)
Change-Id: Ida733fa1747565ec9824d3a37d08b1a73cd8355f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/996
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
No part of ChromeOS seems to use the debug header description, so drop
it to make sure it does not get copied around wrongly.
Change-Id: Icb0baedbf6112f11289b2ddd9618a955a424ddf7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/989
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If microcode.c is built by romcc, this indicates that we are running
microcode updates in the bootblock (e.g. before enabling cache as ram).
In this case we did not enable any consoles yet, so we don't output
anything.
This patch removes inclusion of the unnecessary console/console.h for
that case, which was breaking with certain configurations.
Change-Id: Iebb57794d7b1e84cac253d249d47b88de4dd28a3
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/988
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This fixes my build when specifying an absolute path to the binary.
Change-Id: I95fb3960be70f78146c6afeb9cc777dccdca6b5b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/987
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
It is important to have the system configuration reported as early as
possible to have a better idea what exact chipset the platform is
running with.
This change adds code to have an early coreboot module report the CPU
and PCH information. CPU info includes the 32 bit feature information
word, the symbolic processor brand string, and information about some
features support, as obtained through CPUID instructions.
The PCH information includes the symbolic device name and PCI device
version.
Change-Id: If6c21ad5ffb76d7d57d89f4f87d04bdd7192480a
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/975
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The current early PM setup that attempts to configure dynamic clock
gating relies on PCIe functions to be enabled that may not be.
Instead of reading port 0 or 4 directly to determine the link width
use the register that refelects the soft strapping options as this
will always be available.
Also add a clear register assignment and break for port 0 in the
switch statement instead of falling through to port 4 as that could
end up setting the slot power limit based on port 4 values instead
of based on port 0.
register 0xE1=0x3f and all other root ports should have 0xE1=0x03.
When port 0 and 4 are disabled they will have 0xE1=0x3C before
being disabled by the pch enable handler.
LUMPY default:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.3 PCI bridge: Intel Corporation Device 1c16 (rev b5)
pci_read8 0 0x1c 0 0xe1
0x3f
pci_read8 0 0x1c 3 0xe1
0x03
LUMPY with PCIe port coalesce enabled:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Device 1c16 (rev b5)
pci_read8 0 0x1c 0 0xe1
0x3f
pci_read8 0 0x1c 1 0xe1
0x03
Change-Id: I33a37b0ec0c8e570cf5d9dda2c06e0225fee135c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/980
Tested-by: build bot (Jenkins)
Background: The PCI spec (3.0-3.2.2.3.4) requires that PCI devices
implement function 0. The Linux Kernel therefore will not enumerate
a PCI device if it does not present a valid config space at function 0.
If a board does not have anything connected to root port 0 and it is
desired to disable the unused ports in order to save power then this
will cause the other downstream PCIe devices to go missing as they
will not be enumerated.
Intel chipsets provide a way to map root port numbers to different PCI
function numbers, thereby avoiding this issue and allowing root port 0
to be turned off.
This change adds a new chip config option 'pcie_port_coalesce' that
will collapse the enabled root ports into a linear map starting at
zero. This option defaults to disabled as it can have a confusing
effect on the system as the declared static devicetree may not match
what is seen at runtime. This option is also forced on if the static
devicetree disables port 0.
When each root port is processed in the early enable stage it looks
for a lower numbered root port that has been disabled and then swaps
the two assigned function numbers.
However the mapping register is write-once so it has to keep track of
the proposed mapping changes until all ports have been processed
before writing out the final map value. At this point it also updates
the function numbers in the static device tree so they are consistent
with the new layout.
There are a few other closely related fixes in this change:
1) There is a power savings opportunity if an entire bank of ports
(0-3 or 4-7) are disabled. This was checking the chipset revision to
look for CougarPoint B1+ stepping and that was not passing on
PantherPoint where this should always be applied. To fix this I added
a function to determine the chipset type based on comparing the upper
byte of the device ID.
2) Apply the same chipset type check fix to the IOBP programming.
3) There is another power savings opportunity to enable dynamic clock
gating on shared PCIe resources which only applies to ports 0 and 4.
However if 0 or 4 is disabled then the later check to enable this
would fail as that device is already hidden.
LUMPY current:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.3 PCI bridge: Intel Corporation Device 1c16 (rev b5)
01:00.0 Network controller: Atheros Communications Inc. Device 0030 (rev 01)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B
LUMPY with PCIe port coalesce enabled:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Device 1c16 (rev b5)
01:00.0 Network controller: Atheros Communications Inc. Device 0030 (rev 01)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B
Change-Id: I828aa407fdc9c156c1c42eda8e2d893c0aa66eef
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/979
Tested-by: build bot (Jenkins)
The chipset enforces static-defined interrupt swizzling on PCIe root
ports so if a port is remapped to a different function it needs to
still report the proper interrupt map to the OS instead of assuming
that function number is equivalent to root port number.
This change also includes an update to the PCH function disable
register which was incorrect for CPT/PPT and would cause unpredictable
behavior if used.
The kernel command line was changed to add 'nomsi' in order to force
PCIe devices to use IO-APIC assigned interrupts and not MSI to ensure
that the mapping is correct.
LUMPY current:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.3 PCI bridge: Intel Corporation Device 1c16 (rev b5)
16: 41518 0 0 0 IO-APIC-fasteoi i915, ahci, ath9k
19: 720 0 0 0 IO-APIC-fasteoi ehci_hcd:usb2, eth0
LUMPY with PCIe port coalesce enabled:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Device 1c16 (rev b5)
16: 38988 0 0 0 IO-APIC-fasteoi i915, ahci, ath9k
19: 347 0 0 0 IO-APIC-fasteoi ehci_hcd:usb2, eth0
Change-Id: Ia5f6bb8888b5c38a5dbc88bb25ecdf1fca41ee3e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/978
Tested-by: build bot (Jenkins)
CONFIG_MAX_PHYSICAL_CPUS is defined by quite a number of
mainboards whithout any code actually using the variable.
Hence, drop MAX_PHYSICAL_CPUS from Kconfig for those boards.
In the long run we should drop CONFIG_MAX_PHYSICAL_CPUS use
completely and make the code dynamic or depend on CONFIG_MAX_CPUS
instead.
Change-Id: I37dcc74d245ddba5186b96bd82220dacb6f4d323
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/984
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The sata controller comes up in legacy/normal mode and
is currently put into AHCI mode in romstage.
If that is removed and the controller is left alone until the
ramstage driver (like we do on Stumpy/Lumpy) then the resource
allocator will have configured the device for IDE mode with an
IO address in BAR5. Then when the ramstage driver puts the
controller into AHCI mode it will not have the correct resources
to do the rest of the AHCI setup.
So the controller mode needs to be changed in the enable stage
rather than in the init phase. This same register contains
the port map and it is a R/WO (write once) field so the configured
port map must be written at the same time. For non-AHCI mode
the devicetree map was ignored before but it is used now.
Since the port map register is now written at enable step it
does not need to be written again during init.
With this change the sata port map can be reduced to just port 0
and then U-boot does not have to probe all available ports.
Change-Id: I977952cd88797ab4cea79202e832ecbb5c37e0bd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/977
Tested-by: build bot (Jenkins)
- New table for GT1
- Updates to GT2 17W table
- New table for GT2 35W SKU
- New table for GT2 Other
This also includes a workaround to poll on a different register
when deasserting force wake. On some SKUs the kernel is hanging
when bringing up graphics unless this register is also polled.
Change-Id: I2badf62b464e901cfb0eaf4fc196f59111c71564
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/974
Tested-by: build bot (Jenkins)
- Add config options to set backlight registers
- Update powermeter weight tables for IvyBridge GT1 and
add a new table for GT2 SKU
- Fix a few registers used during GPU PM init sequence
Change-Id: I1500bc07e3ba1bc10c77e7856089e716489dc07a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/973
Tested-by: build bot (Jenkins)
Port u-boot patch for low-level driver:
- Fix bug in traversal of vendor name list.
- Sending "command ready" needs additional logic to handle
TPMs that need that bit set twice: once to empty the read
FIFOs and once to actualy set command ready.
Change-Id: I57c280266b2e966c5b90e4f9e968426a33b93cf1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/972
Tested-by: build bot (Jenkins)
The OS does not re-execute the APMC 'enable ACPI' SMI
on resume so this has the potential to leave things
in an unknown state.
Change-Id: Iaf0fcb99f699e9e0ecacaab3f529026782a95151
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/971
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is done inside the SystemAgent binary on Ivybridge.
Change-Id: I8fb0f593a65a4803e160b284c21b9d5021e2e4a0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/970
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ASPM setting for the Direct Media Interface should no longer be done on
Ivybridge/PantherPoint based systems.
Change-Id: Id30de1beb1b162564048e76712736ccf7049dc7c
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: http://review.coreboot.org/969
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds the PCI device id of the LPC controller identifying the
QPRJ/QS stepping of the Panther Point southbridge.
Change-Id: Idcaa7dbd30224e3690ea469c6cb74f75de287631
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/968
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Many PCI devices share the very same driver despite having different
PCI device IDs, which causes a lot of copy and paste of driver
definitions.
This change introduces a way to specify the array of acceptable
device IDs in a single driver entry. As an example the Intel
{Sandy|Ivy} Bridge SATA driver is being modified to use a single
driver structure for all different SATA controller flavors, a few
more Ivy Bridge IDs are being added as well.
BUG=none
TEST=manual
. modified coreboot brought up an Ivy Bridge platform all the
way to Linux login screen.
Change-Id: I761c5611b93ef946053783f7a755e6c456dd6991
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/982
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Change-Id: I4a64a56dda22050a31232807096e15565a665377
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/967
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Emerald Lake 2 CRB can potentially have more
than 8 CPU cores, so update the number of max cores
accordingly.
Change-Id: Ia42ed8a84916f66dfbfdf2a72cbbed5cea61899b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/966
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Emerald Lake 2 CRB wasn't designed with ChromeOS in mind, so there aren't
any actual developer mode, recovery mode, or write protect switches, let alone
GPIOs to read them from. Instead, I've commandeered signals connected to GPIOs
which are for other things but which aren't used by hardware or, for instance,
the EC to do something Coreboot doesn't control.
The recovery mode switch is connected to GPIO 22 and is called BIOS_REC on the
schematic. The name is at least very reminiscent of the right thing even if
it's supposed to be used for something else. There's a jumper on the board
labelled J8G1 which can force the line to ground, and if not, there's a switch
on the front of the case which toggles its value. "RECOVER" is for recovery
mode and "KEEP" is for normal mode.
The developer mode switch is connected to GPIO 57 and is called SV_DET on the
schematic. It's connected to a jumper labelled J8E2 on the board and, as far as
I can tell, can't be controlled in any other way. When the jumper is in place
and the pins are shorted, developer mode is selected. When the jumper is
removed, normal mode is selected.
The write protect is connected to GPIO 48 which is called BIOS_RESP on the
schematic. It's connected to a jumper labelled J8E3 which, like j8E2, seems to
be the only way to control the line it's on. When the jumper is in place,
write protect is "disabled", and when it's in place it's "enabled" even though
there's no functional difference.
The input for the recovery mode switch was chosen because of the name it
already had on the CRB, BIOS recovery, and because there's a switch to control
it on the front of the case which makes it easy to get at. The jumpers for
developer mode and recovery mode were chosen because there weren't very many
options available, and of those these were next to each other which should
make them easier to find and work with. It might be a good idea to wire toggle
switches up to the pins of those jumpers so they'll be easy to identify, can
be labelled, and would be easier to work with than little jumpers in the
middle of the motherboard.
Change-Id: Ib2c3dc05077dacfbede596dae143ed81a99dbebd
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/965
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This fixes a few cosmetics with the following three boards:
- Intel Emerald Lake 2
- Samsung ChromeBook
- Samsung ChromeBox
The following issues were fixed:
- rely on include path in ASL code instead of specifying relative
paths
- use updated ALIGN_CURRENT in acpi_tables.c
- use preprocessor defines instead of hard coded values where possible
Change-Id: Ia5941be3873aa84c30c13ff2f0428d1c52daa563
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/963
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Instead of the special case in the generic Makefile.inc,
use cbfs-files in the CPU directories.
Change-Id: I71d9c8dff906c9a516ac0dd09a315f8956075592
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/962
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
stages have special cbfstool syntax, which we need to support.
Change-Id: I119255246af818f010acfc7ec2091a6184e74eb3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/961
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
... or fail if repository is not enabled.
Change-Id: I0a1e6d6fed852ec7edf96ace8346ae6b23838a56
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/959
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
This sets up the SMI and SCI inputs on the PCH for Emerald Lake 2 based on my
best interpretation of the schematic. It may not be correct, but it doesn't
seem to cause any problems either.
Change-Id: I21238b3853a92893ec7f08baa2a3ebd35c49dd97
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/964
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
abuild -B enables the use of the blob repository.
Change-Id: I2dd823d3b024ad249d72d668657bf6a6e92145cf
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/958
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
One option to allow using the repo (defaults to no),
one to let boards state that they require it in the
current configuration.
The build system checks out the repo if allowed, and
fails if the repo is requested by the configuration
but not desired by the user.
Change-Id: If71d80b329cf528aa467fcb0b4d9d7c7434aab27
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/957
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Alec Ari